Test Receivers
Devices whose purpose is to capture transmitted signal energy and record specified characteristics. These recordings are then examined to ensure that the sending device is working according to specifications. (www.techfest.com)
-
Product
EMI Test Receivers
-
EMI test receivers; extremely accurate instruments designed to detect electromagnetic emissions rigorously, to ensure all emissions conform to the Standard being tested to. Configured to set up running the required tests for parameters defined by the Standards as simply as possible, including automated test routines. R&S EMI test receivers can be much more too, with a full signal and spectrum analyzer in the same instrument.
-
Product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
Receiver Tester
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
Product
EMI Test Receiver
ESRP
Receiver
The R&S®ESRP EMI test receiver has been designed for diagnostic measurements during development and for precompliance measurements to prepare products for final certification testing. It measures electromagnetic disturbances in the 10 Hz to 7 GHz frequency range, using either conventional stepped frequency scans or FFT based time domain scans to significantly speed up measurements.
-
Product
PCI Express 5 CEM Receiver Test Automation
N5991PC5A
-
The N5991PC5A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 5.0 CEM Add-In Cards and systems.
-
Product
PXE EMI Test Receiver, 1 Hz to 44 GHz
N9048B
Receiver
Keysight's N9048B PXE is a standards-compliant EMI test receiver equipped with an RF pre-selector and LNA designs. Shorten your overall test time and easily perform gapless signal capture and analysis with real-time scan (RTS) capabilities.
-
Product
Receiver Conformance Test Application for IEEE 802.3bm
M8091BMCA
-
IEEE 802.3bm Receiver Test Application for 25GAUI-1 Chip-to-Module, Chip-to-Chip, Cable and Backplane.
-
Product
MXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5181B
Signal Generator
Take your devices & designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading output powerThoroughly test receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
Product
SpaceWire Physical Layer Tester
141
-
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
-
Product
Test Receiver
KH3932
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3932 EM1 test receiver is a fully automatic test receiver and the main tool for EM1 testing. The frequency range of the KH3932 receiver is from 9kHz to 300MHz. Equipped with a power absorption clamp, it can meet the power line disturbance power test. After the artificial power network is configured, the power terminal disturbance voltage test can be carried out. The machine has fast test speed and maneuverability. Strong, stable performance, convenient test data processing and other advantages. The KH3932 receiver uses the USB interface to exchange data with the computer, which makes the transmission speed fast and the bit error rate low. Connect to the computer for testing and use the operating environment familiar to the operator to improve work efficiency.The equipped operating software saves the data of a variety of external equipment, and supports plug and play a variety of external test equipment. The software and hardware are developed by our company. The whole machine uses a fully enclosed structure, and the chassis uses highly conductive materials with good shielding effects. Due to the use of specific technologies and processes, the problem of its own resistance is fundamentally solved. The measurement results are in the international general report format, which can be saved in the computer's hard disk or transmitted through the network, printed out directly, and saved using a USB storage device. The report is rich in content and can be printed directly according to user needs without additional editing.The measurement receiver complies with the requirements of the national standard GBT6113.101 and the international standard CISPR16-1.
-
Product
V4 Marine Communications System - V4 NAVTEX Test System
-
The ICS Electronics Limited V4 NAVTEX Test system may be used for type approval, general performance testing and production testing of NAVTEX receivers.
-
Product
Modbus Simulator
Modbus Slave
-
Modbus Slave is for simulating up to 32 slave devices in 32 windows!. Speed up your PLC programming with this simulating tools. Start programming and test before you receive your slave device from supplier.
-
Product
PCI Express 6 Base Specification Receiver Test Automation
N5991PB6A
-
The N5991PB6A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 6.0 ASICs
-
Product
RF Capture & Player
-
This device can record RF signals in various points of fields. When reproducing the signal data infactories or laboratories, it is possible to test receivers under the reception environment of the data.
-
Product
ITA, G3, 500+ Amps, includes Dedicated 500+ Amp Module
410105174
ITA
ITA, G3, 500+ Amps, includes Dedicated 500+ Amp Module.Contacts rated to 1500VDC for low duty test applications.Mating Receiver 310105172. (NOT compatible with other VPC Solutions)
-
Product
ATSC 3.0 Broadcast Stream Verification
StreamScope XM Verifier
-
The Windows®-based Verifier web app receives, tests, and records ATSC 3.0 broadcast streams from RF, Ethernet, and file inputs. With Verifier, you can monitor real-time graphs and charts of bitrates, signaling tables, RF parameters, packet errors, subframes, PLPs, and other KPIs.
-
Product
RMC
Receive Multicoupler (Rx AIT)
-
*Provides a common receive distribution point for multiple basestations*Each Cellular and PCS unit supplies 8 ports and supports 2 channels*The single 1U tray includes integrated Bias- T and test ports*QMA receive connectors provide quick and sure connections
-
Product
Electrical Receiver Conformance Test (OIF-CEI-56G)
M809256CA
-
OIF-CEI 4.0 Receiver Test Application for OIF-CEI 56G-Very Short Reach (VSR), Medium Reach (MR) and Long Reach (LR) PAM4.
-
Product
Positioning Test System
TS-LBS
Test System
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
Product
DisplayPort 2.0 Receiver Test
N5991DP2A
-
Use the Keysight N5991DP2A DisplayPort 2.0 Receiver Test Software to test, debug and characterize your DisplayPort Sink products maximizing the usage of your test instruments.
-
Product
1465 Series Signal Generator (100kHz – 67GHz)
1465
-
1465 series microwave signal generators, with the frequency range of 100kHz – 67GHz, is provided with high purity spectrum and high output power. It can meet the high-end requirements of electromagnetic signal tests. S1465 series are mainly used in the radar performance evaluation, high-performance receiver test and components parameter test etc., and applicable to aviation, aerospace, radar, communication and navigation equipment etc.
-
Product
Electrical Receiver Conformance Test Application for IEEE 802.3bs/ cd
M8091BSCA
-
IEEE 802.3bs receiver test application for 200GAUI-4 and 400GAUI-8, covering chip-to-module, chip-to-chip, backplane, and copper cable interconnects.
-
Product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
-
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
Product
PCI Express 4 U.2 Receiver Test Automation
N5991PU4A
-
The N5991PU4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express U.2 devices and hosts at 8 GT/s.
-
Product
EMI Test Receiver
ESL
Receiver
The R&S®ESL EMI test receiver combines two instruments in one, measuring EMC disturbances in accordance with the relevant standards and also serving as a full-featured spectrum analyzer for diverse lab applications. The combination of very good RF characteristics and all of the important functions needed for fast, precise measurement and evaluation of the EMC of a device under test in accordance with commercial standards is unmatched in this instrument class.
-
Product
Bit Error Ratio Testers
-
Keysight’s bit error ratio test (BERT) system enables the most accurate physical-layer design verification of high-speed communication and multi-gigabit digital interfaces. Our expert-level support will help you select the high-performance hardware, control software, receiver test, and automation tools needed to help you master your design.
-
Product
EMI Receiver
KH3935
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH3935 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3935 receiver is from 9kHz to 30MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be performed. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing.
-
Product
EMC Test Receiver w/ Real-time bandwidth to 685 MHz
TDEMI ULTRA
-
TDEMI ULTRA offers real-time bandwidth up to 685 MHz, ultra-fast receiver scanning and real-time scanning up to 40 GHz. Offers highest performance for all challenging applications. Also a time-saving and highly efficient full automation of your EMC and communication testings according to all EMC or ETSI standards is available by the EMI64k software suite.
-
Product
ATSC 3.0 Modulator for Lab
ATSC 3.0 LabMod
-
ATSC 3.0 LabMod is the STL Gateway compliant modulator for laboratories. Compact, portable and easy-to-use, LabMod covers the whole ATSC 3.0 standard with LDM support. In addition, LabMod performs channel simulation, noise generation, RF spectrum analysis and RF recording/playing. ATSC 3.0 LabMod is the perfect modulator for discovering ATSC 3.0 standard: generate live ATSC 3.0 RF signals or IQ pattern files, record live ATSC 3.0 transmission in different places over the world (optional) and playback them to test your receiver.
-
Product
PCI Express 4 CEM Receiver Test Automation
N5991PC4A
-
The N5991PC4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 4.0 CEM Add-In Cards and systems
-
Product
Adjustable ISI Channel Emulation Package for M8000 Series BER Test Solutions
M8070ISIB
-
Simplify receiver testing by offering unprecedented flexibility for handling test channels.
