Communications Test
-
Product
Field Communicators
-
We offer modular multi-bus field communicators for HART, FOUNDATION Fieldbus H1 and Profibus PA protocols, combined in some of our process calibrators. While the communicator is built in the same device with the process calibrator, they can communicate seamlessly offering better user experience than separate calibrator and communicator. Plus you only need to carry one device. Thanks to the modularity you can select which protocol you take, and update more protocols later on, if needed.
-
Product
BSD (Test Diagnostics)
test
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
-
Product
Seno-Con Test System
PANTHER 2K QST
Test System
Qmax Test Technologies Pvt. Ltd.
Panther 2K-QST is a versatile ultra fast Seno-Con test system designed to test high volume ,low to high pin count consumer semiconductor IC’s for its assembly line wire bonding faults. Its innovative test technology helps learn from known good device and test against target device drastically reduces time required to develop Test programs.The operating software is designed in such a way that it is fully user friendly with GUI programming.
-
Product
EOL/Functional Testing
Functional Test
Whether you are testing RF LRU modules as a defense contractor, or implementing the next power supply tester for EV charge stations, ARC can create a custom, flexible automated end of line test solution for a variety of needs, with your budget in mind.Leverage our expertise with PXI mixed signal modular instruments, RF test capabilities and switching to complete your next solutions. Shorten your test development times, improve hardware and software standardization, and control your future test development costs by partnering with ARC on your next project.
-
Product
Standalone Bench Test System for FCT, ICT, ISP and Boundary Scan
LEON Bench
Test System
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable Test Adapter) frame allows various fixture houses all over the world to build custom fixtures for the LEONBench. Up to 15U additional rack space allows adding a bunch of high-performance measurement devices from various manufactures. An integrated power distribution unit takes care about power on and off sequencing.As part of the LEON Family, LEONBench is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
Advanced SoC/Analog Test System
3650-EX
Test System
Chroma 3650-EX is specifically designed for high-throughput and high parallel test capabilities to provide the most cost effective solution for fabless, IDM and testing houses.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
Test Instrument
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
Functional Test
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
-
Product
In-Line Test System
Test System
With an Averna in-line test system, clients boost production/yields, catch defects invisible to the human eye, reduce equipment downtime, and ensure repeatable results.
-
Product
NI Real-Time Test Cell Reference System
780590-35
test
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
Product
Data Communications
-
Renesas has receivers, line drivers and encoder-decoders for data communications applications, as well as products that cover ARINC and Manchester specifications.
-
Product
Batterie Inspektor
Battery Test Platform
By combining the most diverse hardware and software modules, Batterie Inspektor™ delivers innovative, automated, and digitalized battery testing at every stage of manufacturing. With this flexible test platform, all modules can be adapted to their respective quality requirements. Manufacturing is simplified through a scalable and standardized framework for both new projects and upgrades.
-
Product
SoC Test Systems
Test System
SoC (System on Chip) devices integrate multiple different functions into a single chip. Our SoC test systems can test all the integrated circuits in SoC devices, including logic, analog, RF, DC and imagers by flexible configuration of the cards/modules used in the test system.
-
Product
Test Fixture
16047E
Test Fixture
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
Product
Rack based antenna test system
R&S®ATS800R CATR
Test System
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique rack based CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
High-Performance Integrated Functional Test Platform
Spectrum-9100™
Test Platform
The Spectrum-9100 is a fully integrated functional test system for factory, depot, and intermediate test applications. It’s the “go to” tester for users needing a mix of digital, analog, mixed-signal, and bus test capabilities across a wide range of products—from legacy boards to advanced systems.
-
Product
One Wire Communication Board
MS 1727
-
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
Product
Serial Communications
-
Data cables are used to physically connect two devices so that data can be transmitted between them. For example, a data cable may be used to connect a data logger to a communication peripheral, a data logger to a computer, a computer to a communication peripheral, or one communication peripheral to another.
-
Product
Functional Test Fixtures
Functional Test
Forwessun’s Functional Test Fixtures are tailored to validate the performance of your electronic assemblies, ensuring each product meets critical quality and functional standards. With customisable designs and precision engineering, these fixtures support a range of testing needs—from checking connectivity and function to confirming performance under real-world conditions. Built to handle rigorous demands, Forwessun's solutions are ideal for industries requiring reliable and repeatable results. Whether for high-volume production or specialised testing, our fixtures provide robust, adaptable support to maintain efficiency and accuracy throughout the testing process. We also create, and work with Ingun to create fixtures using the Ingun kit.
-
Product
Optical Communication Probes
-
Abacus Electrics ANSI Type 2 optical probes utilize infra-red LED technology to provide a galvanically isolated, bi-directional communications interface between energy meters and laptop computers or handheld devices for onsite data retrieval, programming and diagnostics.
-
Product
Communication Gateways
-
We offer compact gateways for DeviceNet™, Profibus™ and Ethernet communication protocols available in RS232, RS422, RS485 and Modbus interfaces for communicating with our programmable automation controllers and networked I/O.
-
Product
PacStar Communications Solutions
-
Curtiss-Wright Defense Solutions
Combining tactical networking equipment and software, our PacStar tactical communications solutions enable enhanced battlefield situational awareness down to the individual warfighter.
-
Product
Fiber Optic Communications
-
Fiber optic converters are installed between the end of fiber optic cables and data loggers to provide a lightning-proof connection.
-
Product
EMS Test System
TS9982
Test System
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
Product
Optical Communication Parts
-
Adamant Namiki Precision Jewel Co Ltd.
Zirconia ferrule sleeve is an important part in optical fiber communication and is the basic product of our optical communication parts. We have developed an optical communication parts part of hasad developed based on grinding and bearings. Offer Optimum Performance And Quality For Each Type Of Optical Fiber, Optical Connector And Optical Device. We Also Offer Pin Gauges And Ring Gauges For Measuring Precise Dimensions Indispensable To Our Quality Assurance . These Gauges Have Little Wear, Good Compatibility With Ferrules And Sleeves, Zirconia , sapphire and cemented carbide are used as materials.Various Optical Connectors And Adapters Using Ferrules And Sleeves, Follow The Long History FC And SC Connectors, MU , LC Connectors Are Also Available. In Particular, LC Connectors Are Deployed In A Wide Lineup With Adapters. In The Field Of Optical Devices, We Provide Codes Master , Various Patch Cords , Conversion Adapters That Connect Different Types Of Connectors, Attenuators And Terminators That Provide Stable Characteristics, Which Are Manufactured Using The Ferrule Quality Of Our Own Manufactured Parts We Will. We Also Offer Parts For Optical Devices SuchAs Fiber Array Used For Connection Of PLC, AWG And Others. In The Field Of Optical Modules, SC And LC Receptacles , Fiber Stub, Pigtail Fiber And Other Optical Module Parts, And Now We Have Provided TOSA, ROSA And Other Optical Module Manufacturing Consignment Services. We Also Deal With Various Lensed Fibers Which Processed Fiber Tip With High Precision . In Addition, We Also Flexibly Deal With Precision Component Processing Used In Optical Communication Field, Special Specification Ferrule, Sleeve Etc. Please Contact Us.
-
Product
Communications ICs
-
Renesas' broad portfolio of communication ICs includes subscriber line interface circuits (SLICs), DSL line drivers, general purpose ringing SLICs, isolated PWM controllers, line card access switches, PABX short-loop SLICs, PLC line drivers, and serializer/deserializer (SerDes) ICs.
-
Product
Communication Converter
F485
-
The F485 is a self-contained device for converting between RS232, RS485 and fiber optic signals. The F485 is electrically isolated to improve communications in noisy environments. The converter uses internal switches to select the signal conversion type and communication rates up to 57600 bps. The F485 converter uses the data on the serial ports to determine direction and therefore requires no hardware handshaking signals from the computer.
-
Product
EBIRST 50-pin D-type To 9-pin D-type Adapter
93-005-238
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Serial / USB Communications
-
Advantech offers serial / USB converters, isolators, repeaters, surge suppressors, data taps /splitter, USB hubs, and industrial communication cards.
-
Product
C012 Communication Board
MS 1728/29
-
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
