RS-485
Serial communication line supporting 32 devices.
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
Remote Particle Sensors
3718-A And 3719-A
-
Kanomax Remote Particle Sensors with analog output are designed to fit into your existing monitoring system, or they can be used as a stand-alone unit to monitor a critical area when connected to an alarm or controller. With two models available, these 2-channel remote particle sensors are capable of Modbus communication via RS485 interface. 0.1 cfm and 1.0 cfm flow rate models are available, along with flexible 4-20mA analog output with the 1.0 cfm unit (only).
-
Product
RS232 Null-Modem Cable, DB-9 Female to DB-9 Female, 2m
182238-02
-
9-Pin Female DB-9 to 9-Pin Female DB-9 Serial Cable - The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
Product
12DO(Source Type) Modbus RS-485 Remote I/O
ADAM-4056SO
-
12ch source type digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system5000VDC isolation protection
-
Product
GPIB Serial Interface
Model 4804B
-
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Product
Digital Interface Boards
Model 2363 OEM
-
* 114515 Board has same digital capability as the 2363 described above with Serial and GPIB IO.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* GPIB header mates with 113640 or 113642 GPIB Connector/Address Switch Cable Assemblies* Accepts 9-32 Vdc power.
-
Product
Serial Interface Device
-
The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Network Analyzers
MPR6 Series
-
Dimensions:96X96kVArh, Max, Min: available (available) % THD I: available (available) % THD V: available (available)Harmonics 1-51.:RS-485:available (available)Digital Input:Digital Output:2AO:0/14-20mA: AO:0/2-10V:Relay:2 Pulse Output: available (available) Hour (RTC): available (available) Memory:1MB Pulse Counter: none (none) Operating Hour: none (none) Alarm: available (available) CT-25: none (none) 110/230 VAC:none (none) 85-265 VAC/DC: available (available) 45-265 VAC/DC: none (none) 10-56 VDC: none (none) Pcs. / Carton:8
-
Product
16DI Modbus RS-485 Remote I/O
ADAM-4051
-
16ch digital inputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system2500VDC isolation protection
-
Product
Economic Type Potentiometer Indicator
CS1-PM
-
CS1-PM economic type Potentiometer Indicator has been designed with high accuracy measurement, display and communication of resistance (3 wires) as like as Positioner.The meter supports Field Calibration function. It can be calibrated with sensor (Potentiometer) to meet machinery structure.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
Serial analyzer
-
The Serial analyzer sink decodes analog data on a serial bus to serial data. It can be used to monitor and analyze RS232, RS485, MIDI, DMX or other compatible serial buses. The serial analyzer can monitor up to eight sources. When these sources are in sync (all sources are of one (combined) instrument), all captured data will be displayed in chronological order.
-
Product
Multifunctional Meter
AEM-DRA
-
The AEM-DRA series has 2 independent and isolated main circuit inputs , can use for different power system.Up to 24 single phase or 8 three-phase circuits, programmable from push buttons with LCM display panel, or using Adtek program software through RS485 communication port.Hardware standard built in a RS485 Modbus communication port , 2 Digital inputs, 4 Relay outputs, LCM and 2 MB flash for data-logging.Optional second communication port for Ethernet, ProfiBus ,LonWorks ,BACnet and Zigbee solutions.Din rail mounting , compact and easy installation, programming through computer and push buttons easy to use.
-
Product
Firmware for High-speed Communication
OP-FW12GA
-
OP-FW12GA is the firmware to increase the speed of monitoring test of bit synchronous communication (such as HDLC/SDLC/X.25, or CC-Link communication), SPI communication, Profibus-DP (field bus known for high-speed communication), UART (asynchronous communication, which is commonly used). By processing great part of monitoring processes by FPGA, it unfailingly captures communication data with time stamps of a microsecond rate. The interface supports RS-232C/RS-422/RS-485/TTL.
-
Product
8Relay Modbus RS-485 Remote I/O
ADAM-4068
-
8ch relayProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs, for RS-422/485
540041010201
-
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs
-
Product
RS-422/RS-485 Repeater
ND-6510
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
IRIG-B TTL TO RS485 Converter
SPC - INS - 1010
-
Signals & Systems India Private Limited
The IRIG-B TTL signal is a time synchronization protocol that can be transmitted up to 50m maximum using coaxial cable. So the relay which is to be received the IRIG-B TTL signal may be far away from the IRIG-B source. The relay may be not able to synchronize with the GPS. To avoid such an incident in the field, some of the relays have provision to receive IRIG-B RS485 signal. The IRIG-B RS485 signal can able travel up to 1200m without any booster. All Time source equipment may not be supplied with IRIG-B RS485 signal output. The converter will act as a bridge between GPS Time source and Relays for time synchronization.
-
Product
Dual-Port Isolated RS-422/485 Communications and Watchdog Card
WDG-2S
-
This multifunction card contains a watchdog timer, two RS422/485 serial communications ports, and an internal temperature monitor and computer voltage monitor. This is a full-length card that installs in "long" expansion slots of IBM PC/XT/AT and compatible computers. The following paragraphs describe functions provided.
-
Product
ARM LPC2364 Board
MS 1541
-
- 128KB On chip Flash- 16*2 line LCD Module interface- Two CAN channel at 1MPBS- Ethernet interface which supports 10/100 MBPS- Full Modem RS232 interface- RS485 interface- RTC (Real Time Clock)- 2048 bits serial EEPROM with data protect and sequential read.- 24 ULN outputs of 12V level.- Eight 110V DC inputs interface.- Six digital inputs interface- Four on board keys interface- Power delay circuit for external use- ON board inspection circuit
-
Product
Digital Panel Meter
VAW
-
VAW DC Multifunction Power Meter provide high accuracy measurement, display and communication of DC voltage, Current, Power, Energy(import / export), and Run Hour. They are also building in 4 Relay outputs, 1 Analogue output, 1 Pulse output , 2External Control Inputs and 1 RS485(Modbus RTU Mode) interface with versatile functions such as remote I/O, alarm and communication for DC power applications like as solar, wind power system or portable electronic device consumption testing.For the power saving, VAW has built in an innovation timer to switch down the light and power of LED. It makes sense to build the meter in a green power system.
-
Product
Sensor Device for Developers
Waspmote
-
Libelium Comunicaciones Distribuidas S.L
Ultra low power (7µA)120+ sensors integrated on 10 Sensor Boards15 radio technologies:Long range: 4G / 3G / GPRS / LoRaWAN / LoRa / Sigfox / 868 MHz / 900 MHzMedium range: ZigBee / 802.15.4 / DigiMesh / WiFiShort range: RFID/NFC / Bluetooth 2.1 / BLEOver the Air Programming (OTA)Encryption libraries (AES, RSA, MD5, SHA, Hash)Certified encapsulated line (Plug & Sense!)Industrial Protocolos: RS-232, RS-485, Modbus, CAN Bus, 4-20mA
-
Product
RS485 Null-Modem Cable, DB-9 Female to DB-9 Female, 2m
183283-02
-
9-Pin Female DB-9 to 9-Pin Female DB-9 Serial Cable - The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
Product
IP Pulse
-
IP Compatible card with 4 programmable pulse generators. TTL or RS422 / RS485 compatible outputs. Programmable pulse - nS to seconds. Programmable count or free
-
Product
I/O Rack
-
ADAM-5000/485 and ADAM-5000E are Modular I/O System, as well as 4-slot / 8-slot Distributed DA&C centralized i/o systems which conform to the EIA RS-485 communication standard. RS-485 was specifically developed for industrial applications to transmit and receive data at high rates over long distances. The ADAM-5000L/TCP and ADAM-5000/TPC are both Ethernet-based I/O systems. Without a repeater, they can cover a communication distance up to 100M.
-
Product
Single Port RS-422/485 Serial PCMCIA Card With Detachable Cable
SSP-200/300
-
The Quatech SSP-200/300 offers a convenient way to add a single RS-422/485 serial port to your laptop, PDA, or desktop (using one of Elan's Desktop PCMCIA adapters - P111, P222 etc.). The card automatically configures to become another COM port using the supplied drivers that are tried, tested, and optimized for Windows.
-
Product
PCI Express 2-Port
7203e
-
The 7203e PCI Express serial interface provides two optically isolated serial ports, each individually configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C952 UART with 128-byte Tx/Rx FIFOs that enables data rates to 460.8K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
RS232 / RS485 / RS422 / Ethernet Surge Protectors
-
Our passive, rugged, industrial-grade RS232 / RS485 / RS422 / Ethernet surge protectors are designed for direct industrial DIN-rail mounting and they come with two (2) or three (3) stages of surge protection — Gas Discharge Tube (GDT), protection resistors, and Transient Voltage Suppressor (TVS) - for maximum protection. From 2-wire RS485, 4-wire RS422 / RS485, to 10 / 100 / 1000M Ethernet, CommFront's surge protectors safeguard your data lines and provide you with a peace of mind.
-
Product
ANSI X3.28 Interface Board
Model 4804B-7
-
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Product
3U Processor Board
CP39101
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP39101 is a 3U CompactPCI 4-channel independent isolated serial communication board, designed for industrial communication applications, compliant with PICMG R3.0 2.1 specification.CP39101 adopts EXER 17D158 communication processor as the master control chip. Each of the on-board 4-channel serial port can be individually configured as RS232, RS485 or RS422, and in any mode, CP39101 can be operated properly in extended temperature ( -40℃ to +85℃ ) range.
-
Product
Multifunction Counter (Pulse Input)
CM1-CT
-
CM1-CT multifunction counter(position) display controller, is design to have 2 pulse input, for proximity switch, photoelectric sensor, encoder etc.. Counting increase or decrease, positioning batch count etc.. display, with External input and Modbus communication port.Multiple types of input mode, trip mode setting to fulfil easy usage and requirement for counter controller. For different requirement, the meter can be with 2 relay or 1 Analogue output or 1 RS485(Modbus RTD mode) communication. (Choose 1 kind of output from the 3 options)
-
Product
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
NI-6584 / 781290-02
-
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
