-
product
Channel Emulator
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
product
JTAG Emulator
Spectum Digital XDS510-USB
The Spectrum Digital XDS510 JTAG emulator is low cost and has a USB powered interface.
-
product
and EET200E - Encoder Emulator Tester
EET-200
End the shotgun approach to troubleshooting and reduce the time spent diagnosing altitude encoder/transponder problems. TRANS-CAL INDUSTRIES' EET-200 and EET-200E offers the avionics technician an inexpensive diagnostic tool for altitude encoder/transponder troubleshooting.
-
product
Network Emulation, Delay Simulation, Bandwidth Emulator & WAN Simulation
GigaNet System’s network emulation appliances provide precision, performance and predictability in your test infrastructure resulting in optimized system performance and robust system behavior under real world network conditions.
-
product
Ultra Multi-Channel Battery Emulator
Peritec Ultra Multi-Channel Battery Emulator is used for the development of electric car(EV). The hardware has great extendability, it can also simulates up to 192ch synchronized DC power supply with high isolation and you can make the test sequence with Mirosoft Excel.It can be used as a power source such as a simulator of new energy development for the evaluation. In addition, we can correspond flexibly to customize provide the best solution to suit the needs of our customers.
-
product
PCIe Exerciser & PCIe LTSSM Exerciser with L1 Substate Analysis
U4305B
Supports 2.5 GT/s (Gen1), 5.0 GT/s (Gen2) and 8.0 GT/s (Gen3) speeds Link width support x1 through x16 lanes Standard PCIe half-size card form factor to fit into most platforms Emulate Root Complex (RC) or Add-In-Card (AIC)
-
product
Low Cost Emulator
EB-XAG3
# Emulates P51XG1/2/3x Microcontrollers# Real-Time Operation up to 30MHz# 3.3V or 5V Voltage Operation# Source-Level Debugger for C and Assembler# MS-Windows Debugger Software# Reduced Set of C-Compiler and Assembler# Support for ROMless and ROMed Microcontrollers# 64K of Code Memory# Performance Analyzer
-
product
Network Emulator and Protocol Tester
Maxwell Pro
The Maxwell Pro Network Emulator helps engineers learn how their products will perform in mobile, cloud, and WAN networks. By capturing and changing network flows, Maxwell Pro can induce the conditions that cause network congestion, slow links, time outs, Lossy networks (LLNs), and many other adverse network conditions. Engineers can then see the effects on the device or application to find and fix bugs, solve network problems, and learn the limits of device and application performance.
-
product
Network Emulator Software
NetDisturb
NetDisturb allows disturbing flows over IP networks helping to study the behavior of applications, devices or services in a “disturbed” network environment. NetDisturb is inserted between two Ethernet segments acting as a bridge and operates bi-directional packet transfer on Ethernet, Fast Ethernet and Gigabit network interface cards.
-
product
Regenerative AC Emulator, 600 VAC, 63 A, 45 KVA, 3‑Phase
SL1202A
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
product
Base Station Emulator
SUTP 5018
Designed to create a custom cellular environment to serve testing and characterization needs. The combination of high power, real-time computing and the software defined radio platform enables this instrument to create your own cells for testing in a compact size and cost-efficient way.
-
product
Regenerative AC Emulator, 600 VAC, 125 A, 90 KVA, 3‑Phase
SL1203A
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
product
Emulates Dallas Semiconductors DS89C420
FE-C420
* Emulates Dallas Semiconductors DS89C420 * 16K Code Memory * Real-Time Emulation * Frequency up to fmax at 3V and 5V * ISP Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
product
Live PD Emulation For The PSL-3424
Flexibly Mimic Class 0 to Class 8 Powered Device Per PSL-3424 Test Port. Configure up to 96 IEEE 802.3 PD’s on Any Combination of 2-Pair and 4-Pair PSE Ports with Loading up to 100W on Every Port. Emulated PD’s Automatically Handle PSE Power Demotions (Assigned Class). User-Defined Powered Device Load with Optional Cable Loss Modeling. Emulate 802.3at and 802.3bt PoE-LLDP* Negotiations and Power Adjustments (PSL-3424L). Monitor Multi-Port Live Emulation Status.
-
product
JTAG Emulators
XDS100v2 Series
The XDS100-class JTAG Emulator is an ultra-low-cost entry level JTAG debugger for TI devices. Blackhawk offers two models, each with two JTAG target connections. One model includes TI JTAG connections for 14-pin TI and 20-pin cTI JTAG headers. The other model provides ARM 10-pin and 20-pin JTAG connections. Both models are identical in software and device support except for the the target connections, so pick the one that matches your target board connection.
-
product
UI Test Tool for Web, Java, Windows, Android & iOS
QF-Test
QF-Test is the established tool for professional GUI test automation of desktop, web & mobile applications as well as PDF documents. QF-Test is a low-code GUI test tool that allows you to efficiently create test cases, e.g. using Capture/Replay, without any programming knowledge across platforms on Windows, Linux and macOS. For software developers, Jython, Groovy or JavaScript offer advanced scripting possibilities. Tests can be run automatically via continuous integration tools such as Jenkins and generate detailed log files and XML or HTML reports. Use QF-Test to create robust and stable regression tests for various GUI technologies. QF-Test supports all types of Java GUIs, ranging from Swing (including ULC, JIDE components, CaptainCasa), its successor JavaFX, as well as the Standard Widget Toolkit (SWT) and Eclipse, including plugins and RCP applications. You can also use QF-Test to test dynamic web applications based on Angular, React or Vue.js, for example, including Electron and hybrid applications using JxBrowser, JPro or WebSwing, for example. QF-Test supports native Windows desktop applications created with Win32, .Net, Windows Forms, WPF, Windows Apps. Mobile applications can be tested on real devices or with the Android Studio Emulator or iOS Simulator and Xcode.In addition, you can test automated whether your web application complies with common accessibility standards in just a few simple steps. PDF documents can also be conveniently tested automatically with QF-Test. On the market since 2001, the test tool is continuously being actively developed and is currently used by more than 1,500 companies across 60 countries. Contact us by e-mail at service@qftest.com or get a free trial version at www.qftest.com/en!
-
product
Sensor Signal Emulator
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
product
Mobile Wireless Network Emulator
WISER
WISER 50-node wireless network emulator. Includes mobility, path-loss, CDMA time-slot emulation and more. Designed to emulate US Military network designs and may be applicable for other mobile wireless networks. Supports up to 50 nodes (vehicles, radio towers, etc). WISER is a joint project between Telcordia and Candela Technologies. Please see Telcordia's WISER Web Page for implementation details and research papers.
-
product
Network Emulation
PacketStorm Communications, Inc.
The PacketStorm IP Network Emulators and simulators reproduce the unfavorable conditions of IP Networks and WANs in a controllable and repeatable lab setting. PacketStorm is the Industry leader of Layer 2 and Layer 3 WAN emulation and network bandwidth simulation.
-
product
Design & Test Software
Industry-Leading Design, Emulation, and Test Software.Harness the power of digital twins, artificial intelligence, and automation to streamline workflows, break down silos, and accelerate test cycles.Find out why so many innovators trust Keysight to build their next breakthrough. With software spanning electronic design automation (EDA), instrument control, emulators, IT operations, and application delivery, your next project's only limitation is what you dare to dream.
-
product
Battery Emulator And Profiler
E36731A
The Keysight E36731A battery emulator and profiler is an integrated electronic load and power supply developed to use with Keysight PathWave BenchVue battery emulation software. An emulated battery gives you a known good reference for testing at any charge level. Quickly assess the effect of design or software changes on battery life by emulating any battery charge state. Leverage emulation and precise current drain analysis to achieve longer battery life or to reduce the size of your device.
-
product
Live PD Emulation
Flexibly Mimic Class 0 to 4 Powered Device Per PSA/PSL-3000 Test Port. Configure up to 192 Simultaneous IEEE 802.3 PD’s. User-Defined Class 0 - 4 Powered Device Modeling with or without Cable Loss. Emulate 802.3at PoE-LLDP Negotiations and Power Adjustments. Monitor Multi-Port Live Emulation Status. Available to PSA-3000 and PSL-3000 Platforms as optional license feature.
-
product
Terminal Emulator
Distinct IntelliTerm
Distinct IntelliTerm is a terminal emulator that allows you to access data on diverse corporate information servers such as IBM mainframes, IBM AS400, UNIX and VAX systems from a single application. It includes full featured terminal emulation for TN3270E, TN3270 for Type 3278 and 3279, with support for 3179G, 3192G, 3472G and 3279 S3G graphics, TN5250 and VT52 through VT420. Distinct IntelliTerm operates over the Telnet protocol running over TCP/IP, an area in which Distinct is a market leader. Distinct IntelliTerm integrates related utilities such as multi-connect FTP with SOCKS proxy support, print server support with LPD and 3287 printing support, substantially reducing your training and support costs.
-
product
Testing Solution & Battery Emulation
PLUTON
The PLUTON solution is a programmable DC power supply designed to function as a source or a regenerative charge.
-
product
Fading Emulator
RI 241
RI 241 Fading Emulator is a radio channel emulator designed to replace the obsolete Agilent 11757B Multipath Fading Simulator.
-
product
Handover Emulator
Qosmotec Software Solutions GmbH
The Qosmotec handover test system QPER is a versatile test platform for emulating the RF signal between radio devices in a wireless network, e.g., between mobile stations and radio infrastructure of a mobile network. It is employed in test beds where radio signals are transmitted through coaxial cables and specifically manipulated by testers. QPER can be based on various hardware platforms, from attenuator arrays to digital channel emulators.
-
product
Host emulator
E84
Precision Development Consulting Inc
A USB controlled and self-powered emulator for functional testing SEMI E84 implementations. (E84-1000) This was developed because there was nothing like it in the marketplace, and it was clearly needed. This product enables a factory automation engineer to perform E84 functional testing anywhere in the world. Weighing less than 5oz, it is neither a burden, nor a power hog. You will never need to look for an additional power receptacle in the fab. The emulator gives the user full control over the sequence so that any test can be performed. Existing products were large and unwieldy, and provided canned tests that could not be modified to meet the requirements that Fab managers impose on their suppliers.
-
product
Dual Mobile Comm DC Source w/ Battery Emulation
66319B
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections. The Keysight 66319B dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a rack box) and eliminates the need for two separate power supplies.
-
product
EMULATION TESTING
STORAGE
SANBlaze Technology, Inc. is a pioneer in storage emulation testing technologies and a leading provider of storage, networking and multifunction solutions for embedded systems. SANBlaze emulation systems are deployed in the test and development labs of most major storage hardware and software vendors worldwide.
-
product
Dual Mobile Comm DC Source w/ Battery Emulation, DVM
66319D
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.
