Filter Results By:
Products
Applications
Manufacturers
-
product
ESD LCD SURFACE RESISTIVITY METER (WITH 1 PAIR OF 5 POUND ELECTRODES)
The ESD LCD SURFACE RESISTIVITY METER provides everything necessary to test work surfaces using the procedure outlined in the EOS/ESD-S4.1 standard. This test kit makes testing surface resistance easy – simply place the weights attach the cables, switch to the correct voltage and press the button to read resistance directly on the meter. The meter incorporates parallel probes on the bottom of the unit which allows the user to make surface resistivity measurements. The parallel probes allow for quick and easy testing of a variety of surfaces and materials, without the use of the five pound electrodes
-
product
ESD Test Simulator
ONYX16
The ONYX is a state of the art electrostatic discharge simulator available in 16kV or 30kV versions. It is the most ergonomic 30kV ESD gun without an additional base control unit that can be battery or mains operated. The easy to use touch screen, ergonomic design, modular RC units, multilingual interface, remote control software, built-in LED light and temperature & humidity display allows for trouble-free use of the ONYX in all types of test sites.
-
product
Impulse Semiconductor High Current Integrated
Transmission Line Pulse Test System
The Impulse Semiconductor High Current Transmission Line Pulse (TLP) test system is the tool of choice for extracting ESD parameters for transient protection devices in a package, or at wafer level. With accuracy better than 100 milliohms at 40 amps peak current, the Impulse high current TLP is specially tailored to the needs of today's ESD device designers who must accurately measure low values dynamic resistance irrespective of breakdown voltage.
-
product
Microelectronics Test & Engineering Services
EAG's Microelectronics Test and Engineering lab network provides semiconductor and electronics design firms worldwide with test, debug, and early engineering support to help you with new product introduction. We actively service a broad range of semiconductor and electronics companies worldwide. Services include ATE testing, Reliability testing and qualification, ESD testing, Failure Analysis, FIB Circuit Edit and Debug. for both ICs and systems
-
product
1Gsps, 18 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV518
- Physical Channels: 18- Sample rate: 4ch@1 Gsps or 9ch@500Msps or 18ch@1Gsps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns or 18 ch. are sammpled every 4ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
product
Immunity Development System
Used for EMI suppression in printed circuit boards during the development phase. The developer can use the E1 set to quickly identify the causes of burst and ESD interference. This allows the developer to design suitable measures to solve the causes of the interference. It can also be used to test the effectiveness of the measures taken.
-
product
PRODUCTS TESTING
ESD
MicroStat Laboratories -R.E.T.S.
Our ESD test capabilities include resistance, resistivity, electrostatic shielding, charge generation, and charge dissipation. We routinely test flooring materials, packaging, footwear, garments, ionizers and many other ESD control products and materials. We utilize the relevant test methods and standards of the ESD Association, ANSI, ASTM, NFPA, IEST, IEC, AATCC, or our clients’ in-house specifications.
-
product
ESD Simulators
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
product
ESD Discharge Simulator
Model 9910 PurePulse/PinScan
Model 9910 PurePulse / PinScan is used to determine the ESD susceptibility level of electronic devices up to ±4kV. PurePulse generates ESD pulses up to 4kV for testing electronic devices for susceptibility to Electrostatic Discharge (ESD) using HBM, MM and HMM models. PinScan provides automatic sequencing of ESD testing of up to 128 pin devices, applying a discharge, thenperforming a curve-trace test to identify a failure.
-
product
ESD Tester
Tokyo Electronics Trading Co., Ltd.
Is performed to test the susceptibility of ICs and electronic devices to ESD.
-
product
20KV 30KV Electrostatic Discharge ESD Simulator
20KV/ 30KV Electrostatic Discharge ESD Simulator
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD-0230/ESD-0220 has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
product
Automated DC Parametric Curve Tracer
MultiTrace
MultiTrace curve tracer is a mid-sized benchtop model supporting pin counts from 216-625 pins and includes the PGA-625 fixture as a standard interface. MultiTrace supports a wide range of test applications: Failure analysis, Reliability testing, Counterfeit device analysis, Nondestructive electrical counterfeit test, Opens, shorts leakage testing (OSL), Post decap electrical inspection, Optical fault localization, ESD testing, Latch-up testing, Supply current measurements, and more!
-
product
Surface Resistance System Kit
PRS-801RM
- Perform Point-to-Point and Resistance to Ground Measurements from 0.01 Ω to 200 Teraohms- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Measures in accordance with ESD TR53, ANSI/ESD S4.1, ANSI/ESD S7.1, ANSI/ESD STM97.1 and others- Constant Test voltages 10V and 100V meeting ANSI/ESD S20.20- Operates using a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- Stores up to 999 Test Values Into Memory- Compatible with Prostat Connect 2.0 for Downloading into Excel®- Charging and Download via Standard Micro USB Cable- Includes 5lb Conductive Probes and Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
product
Digital/Analog Audit Kit
Botron's Digital/Analog Audit Kit insulation and continuity tester is designed for electrical testing. The wide range of test voltages makes the Audit Kit ideal for users involved with ESD testing. The kit gives greater functionality with simplified operation and an ergonomically designed case.
-
product
ESD Packaging Test Kit
PRF-911PT
The PRF-911 Concentric Ring is to be attached to the PRS-801B Resistance System included in this Packaging Test Kit. This system will also give you surface resistivity by multiplying the surface resistance measurement in ohms by 10 to obtain surface resistivity in ohms/square. The PRF-911PT meets requirements from ANSI/ESD STM11.11, ANSI/ESD STM11.12 snd IEC 61340-2-3. It will also approximate surface and volume resistivity measurements per ASTM D-257.
-
product
Electrostatic Discharge
Our electrostatic discharge (ESD) measurement and control solutions include charge plate monitors, sensors, resistivity meters, and voltmeters. Reliably monitor, measure, locate, and test for static electricity.
-
product
ESD Generators
The ESD Simulators ESD suitable for performing EMC tests of systems and equipment according to the standards IEC / EN 61000-4-2 and ISO / TR 10605. It can far beyond the standard boundaries higher test levels are adjusted. Depending on the device under test and the test setup are two test method shall be: Air discharge (AIR) and contact discharge (CON).
-
product
Electrostatic Discharge Simulator
ESD61000-2
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD61000-2/ESD61000-2A has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
product
Eurostat Turnstiles
For companies who need to ensure that the operators cannot enter the EPA unless their wrist straps and footwear are compliant every day• The turnstiles comply with ANSI/ESD S20/20 specification and ISO standards record keeping requirements • Both ESD safe shoes are tested separately through measuring electrodes, installed in the contact mat.• This system tests operators quickly (≤ 3 sec) and automatically and generate reports for the ESD coordinator• Communication with a server for traceability (Operator ID, Time & Date, Test values etc…)• LCD screen showing real time measurement• Keypad• Hygrometry measurement• Choice of measuring ranges and system calibration directly with the software• HID Wiegand interface, compatible to any HID card format
-
product
Plant Auditor's Surface Resistance Kit
PMK-153
The PMK-153 Resistance Test Kit contains the instruments you need to take resistance measurements.The PMK-153 includes the PAS-853B Wide Range Ohmmeter with 5 pound Conductive Rubber Electrodes. The PAS-853B instrument is a wide range ohmmeter that measures accurately from 0.01 to 9.9x1012 ohms. In AUTO mode the instrument automatically adjusts resistance range and selects test voltage in accordance with standard practices outlined in ANSI/ESD STM11.11, and meets audit requirements of ESD TR53.
-
product
Semiconductor & Electronic Systems Test and Diagnostics Services
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
-
product
ESD Test System
58154 Series
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
product
Pulsed IV-Curve Solutions
Pulsed IV-Curve Test and Analysis System is our new development for 2015. It is an advanced and compact pulsed IV-curve characterization system designed to simulate pulsed ESD events such as TLP, vf-TLP, HMM, HBM, EFT, and LV-Surge. It will monitor the transient voltage and current waveform during the pulse in ps or ns segment, and test the pre- and post-pulse status (leakage current, breakdown voltage, biasing current, static IV curve, etc) of the device under test (DUT), such as protection devices, semiconductors, circuit modules, touch panel sensor, etc.
-
product
Wafer/Chip/Package Semi-automated ESD Tester
400SW
Tokyo Electronics Trading Co., Ltd.
Semi-automated ESD tester featuring Ecdm 400E, Universal ESD Simulator. Used with a manual wafer probing system or a die manipulator, wafer or die level semi-auto ESD test can be done, as well as packaged device test. Damage is detected by V-I curve or leakage current change detection. Stress level and measurement points are programmed by personal computor via GP-IB. Once test terminals are selected, ESD endurance is automatically measured.
-
product
Wrist Strap Tester
Statclean Technology (S) Pte Ltd
ESD wrist strap is most commonly used protective devices which prevent the build-up of electrostatic charge on personnel. The random failure of wrist strap compromises the protection. Thus, it is important to test every wrist strap regularly.
-
product
Ohm-Stat Guardian Pro Constant Monitor
Tests two people and two wriststrapsLED and buzzerNIST calibration includedWorks with all single wire capacitance wrist strapsAll cords suppliedCE markCan be calibratedProduct conforms to the ESD S.20.20 spec standards110v AC powerGround dock included
-
product
ESD Latch Up Tester
1100-ESD
Tokyo Electronics Trading Co., Ltd.
The Model 1100-ESD can easily and accurately perform ESD tests (HBM, MM) on ICs up to 64 pins. Also, all common pin combinations required by the standard can be realized.
-
product
Shoes and Wrist Strap Tester
WST100
• Tester designed for checking the conformity of operators wrist strap and/or shoes to the ESD protection standard.• It is also designed to be permanent wall mounted in a production facility for daily testing of employee’s wrist straps and footwear.• Easy to operate, red and green LEDs give clear “pass” or “fail” indication• Individual tests for the wrist strap, the right and left shoe• Can register up to 60 000 different measurements• Output for interface with PC or automatic door opening system• Operates battery that can be supplemented with an AC net adaptor• Tester and calibration plug are delivered with a certificate ofcalibration
-
product
Test System
4003 TLP+™
The Model 4002 TLP+™ test system was the first turn-key commercial TLP developed for the ESD industry and has remained the leader in the ESD square pulse testing field since this method was first introduced in 1989. This tester is the ultimate design and analysis tool for ESD protection circuits. It provides Pulse Curve Traces of circuit characteristics which simulate ESD tests. This allows you to see into a chip’s operation taking out the guesswork which speeds your design and minimizes lost time.
-
product
ESD Testing
MicroStat Laboratories -R.E.T.S.
A leading independent ESD test company, MicroStat Laboratories/River’s Edge Technical Service maintains a fully equipped ESD test laboratory committed to the testing and evaluation of products, materials, and processes used in electrostatic discharge (ESD) control.
