Audio Spectrum Analyzers
characterize audio frequencies between 20 Hz to 20 kHz.
See Also: Spectrum Analyzers, Audio Analyzers, Optical Spectrum Analyzers, RF Spectrum Analyzers
-
product
Logic Analyzer
GoLogicXL-36
Logic analyzers and oscilloscopes offering fast sample rates and large memory depths are required to debug and test modern electronics. The GoLogicXL captures a very large window of bus activity using sample depths up to 1 billion samples. 4 GHz sampling rates expose the finest details in your signals. 1 GHz Transitional sampling provides the optimum method to capture fast data bursts separated by seconds, minutes, or even hours of bus inactivity. The GoLogicXL State analysis can also synchronize with single-data-rate 300 MHz SDR clocks, and double-date-rate 250 MHz DDR clocks (500 MHz effective).
-
product
PXIe Vector Network Analyzer
M937xA Series
The Keysight M937xA vector network analyzer (VNA) performs fast, accurate, measurements and reduces your cost-of-test by giving you simultaneous characterizations for two-port or multiport devices with a single PXI chassis.
-
product
PCI-GPIB+, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows, Onboard GPIB Analyzer
778033-01
The PCI‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCI slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCI‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Solar Analyzers
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)The Remote Solar Detector is moisture-proofIntelligent test logic with no personnel attendance required in the field Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detectedMax. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax Voltage at open circuit (Voc), Current at short circuit (Isc)Efficiency (%) calculation of solar systemTemperature measurement of solar panelsIrradiance measurement of sun lightSeries resistance (Rs) calculation of solar panelsWith data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standardProvide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)Users can set up the parameters of solar panelsUsers can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurementThe Irradiances and Temperatures of solar panels can be continuously measured, monitored and recordedContinuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
-
product
Spectrum Analysis For P50xxB Up To 53 GHz
S970908B
Add spectrum analysis to your P50xxB Streamline series vector network analyzer
-
product
Multi-service Network And Telecom Analyzer
NetProbe 10G
Multi-service Network and Telecom Analyzer. The NetProbe 10G is the latest introduction to NetProbe family of handheld testers. The NetProbe 10G comes with 10G Ethernet basic functionality as standard and can be software upgraded anytime with advanced 10G Ethernet, IPTV, VOIP, WIFI and IEEE C37.94 options.
-
product
PC Control UV-NIR Optical Spectrum Meter
NI4000
NI4000 PC control UV-NIR optical spectrum meter was designed to provide full spectral output throughout the 200-1100 nm range, with best efficiency at 200-1050 nm.
-
product
Portable Measuring Complex - Analog Signal Analyzer
The system is designed to collect data during model tests in a pilot pool.The complex is built on the basis of a laptop in a protected design, a National Instrumrnts data collection board and two external connector blocks with BNC connectors, allowing you to connect up to 32 analog signals.
-
product
WiFiScope WS6: 200 MS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-200XM-W5
*Oscilloscope / Spectrum analyzer / Voltmeter*14 bit (0.006 %) resolution (16 bit enhanced resolution)*200 MS/s sampling*250 MHz bandwidth*Up to 64 MSamples memory per channel*0.25 % DC vertical accuracy*1 ppm timebase accuracy*WiFiScope advantages
-
product
Tone Analyzer Service
The IBM Watson Tone Analyzer Service uses linguistic analysis to detect three types of tones from written text: emotions, social tendencies, and writing style. Emotions identified include things like anger, fear, joy, sadness, and disgust. Identified social tendencies include things from the Big Five personality traits used by some psychologists. These include openness, conscientiousness, extraversion, agreeableness, and emotional range. Identified writing styles include confident, analytical, and tentative.
-
product
Full-Size PCI Express Mini Module With Audio
AX92905
*USB to Audio as Mic-In/Line-In/Line-Out*Supports one half-size PCI Express Mini card slot (PCIe only)*Cmedia CM6510B controller*51 x 30 mm
-
product
LED Thermal and Electrical Performance Analyzer
T5
Thermal parameter is the key index to evaluate the performance of LED. It’s very important to measure thermal characteristics of high power LED for high reliability LED applications. It will have effect on the optical parameters, electricity parameters and lifetime of LED. Therefore, design and control of the thermal dissipation is the most important thing for the manufacturers and users.
-
product
BTA Analyzer
The new BreakThrough Analyzer (BTA) is a flexible gas delivery and management system for the precise characterization of adsorbent performance under process-relevant conditions. It delivers reliable adsorption data for gas/vapor mixtures using a flow-through system.
-
product
LogicPort Logic Analyzer
LA1034
The LogicPort provides 34 channels sampled at 500MHz. This includes two state-clock inputs which function as normal sampled channels in timing-mode. The LogicPort logic analyzer's hardware is controlled and powered via your PC's USB 1.1 or 2.0 port for the ultimate in convenience and portability.
-
product
Precision Impedance Analyzer (10Hz to 130MHz)
ST2851
ST2851 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. It is based on Windows10 operating system, which realizes a fully computerized operation interface, making the measurement more intelligent and easier.ST2851 series impedance analyzer surpasses the 120MHz frequency bottleneck of similar foreign instruments, and solves the defect that it can only be analyzed but cannot be tested independently. At the same time, it adopts two interfaces of single test and analysis to make the test easier.
-
product
6 Contacts- Circuit Breaker Analyzer
CB14
The CB14 is a 6 contacts circuit breaker analyzer designed to perform Timing, Motion as well as Static & Dynamic Resistance Measurement (DRM) in a single test. It also includes 3 multifunction analog inputs.
-
product
Hydrogen Analyzer
H‑500
Determination of hydrogen using the heat extraction method is a special requirement for the characterization of steel, steel alloys, copper and other metals. ELTRA’s H-500 is designed for the rapid and accurate determination of hydrogen in these materials. The H-500 analyzer uses the heat extraction technique and is equipped with a resistance furnace with quartz tube. The temperature can be set up to 1000 °C in steps of 1 °C. The usual working range of the H-500 is about 900° to 1000° C.
-
product
Oil-In-Water Analyzer
RTG100
The Mirmorax Oil-in-Water analyzer is based on an ultrasonic measurement technique which is a direct measurement on individual acoustic echoes that are characterized using advanced signal processing.
-
product
Combustion Control Oxygen Analyzers
The combustion control oxygen analyzers from PST utilize zirconia sensors for measuring stack gases on boilers, process heaters, incinerators, crematoria and other high temperature/humidity applications.
-
product
Engine Performance Analyzer
H337H-2
Verifies engine performance during troubleshooting and after module replacement
-
product
Continuous Time Interval Analyzers
GT668PXI-1
GT8000IP is a 7 slot PXI chassis with a touch screen display that is best suited for bench top instrumentation.
-
product
Bus Analyzer / Exerciser
VME850
The VME850 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to 2eSST protocol. In addition to the VME bus, user defined signals on the P0 and P2 connectors are also analyzed and exercised with optional plug-in modules.
-
product
Electrochemical Analyzer
EC Epsilon EClipse
The Epsilon EClipse™ is the latest electrochemical analyzer manufactured by BASi. It is a potentiostat/galvanostat with a second working electrode for bipotentiostat measurements. It comes with software that enables the most popular electrochemical techniques such as cyclic voltammetry, chronoamperometry, and chronopotentiometry (select Techniques below for a more complete list). The Basic Plus software can be purchased to enable pulsed voltammetry and stripping voltammetry techniques.
-
product
PC Based Automatic Sequential Analyzer
D-9003 AS, D-9005 ASR
The PC Based Automatic Sequential Analyzer is the most comprehensive tester designed to automatically check the quality of 1φ & 3φ wound stators in fast paced production motor shops.
-
product
Bus Analyzer / Exerciser
VME850P0
The VME850P0 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P0 connector. This module allows the user to monitor and stimulate the A, B, C, D and E rows of the 95 pin P0 connector. Although the VME850P0 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P0 connector must be less then 5V in order to prevent damage of the analyzer.
-
product
Power Analyzer
PeakTech Prüf- und Messtechnik GmbH
Measure the quantity, quality, and frequency of electric power.
-
product
Automated Wear Debris Analyzer
LaserNet 200 Series
The LaserNet 200 Series allows reliability professionals to quickly and easily assess machinery health in just minutes. By testing only a few milliliters of fluid, users see a complete picture of machine wear and particulate contamination. This enables the user to determine filtration efficiency, the type of wear mode occurring, and the change in ferrous debris concentration, for maintenance action.
-
product
Vector Network Analyzers
The Teledyne Test Tools range of T3VNA Vector Network Analyzers consist of two models with a Vector Network Analysis frequency range of 10 MHz up to a maximum of 3.2 GHz and a Spectrum Analysis frequency range from 9 kHz up to a maximum of 3.2 GHz. The small footprint and easy user interface is augmented by a high performance specification with many advanced measurement functions and capabilities.
-
product
Universal PD & EMI analyzer
Spark P3
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
product
Worst-Case Execution Time Analyzers
aiT WCET
AbsInt Angewandte Informatik GmbH
In real-time systems, timely task completion is of the essence. Each real-time task has to be completed within a specified time frame in order to ensure that the system works correctly. In other words, it is essential that the WCET of each task is known.
