Spring Probes
Spring loaded electrical conductor contacting elements. Also known as: Pogo Pin
See Also: Pogo Pin, Test Fixtures, Bed of Nails
-
Product
Test Contactor/Probe Head
Mercury
-
Mercury™ test probes and contactors are excellent spring probes for the laboratory though they were designed with the robust qualities needed for high-volume production test. Their unique design ensures excellent plating quality for low, consistent resistance, long life, and high-test yields.Mercury probes are available with minimum pitches of 0.3 mm, 0.4 mm, 0.5 mm, and 0.8 mm, to provide the best performance at any device pitch. Mercury probes have bandwidths of up to 22 GHz, and can carry over 3 Amps of current. The Mercury is an excellent choice for any test application.
-
Product
High Force Type Spring Probes
-
Total length of spring probes for high force is longer than standard type and is more optimized to use for testing PCB. We have 1mm to 2.54mm pitch and you can choose not only tip type but also spring force for each pitch. This makes it possible for you to choose spring probe suits the best for your use.
-
Product
Spring Probe For Testing Bare Board And/or PCB
-
You can see Spring Probe for testing bare board and PCB here. Standard pitch is from 0.5mm to 3.0mm.
-
Product
ATE Socket
-
Design ATE socket according to customer's requirementsUse on auto-test eqiupments and handler.Pitch range from 0.30 to 1.0mm.Pin amount: 2 and above.Key material: Peek,Torlon.etcContact with top pogo pin
-
Product
Kelvin Test Contactor/Probe Head
Gemini
-
At 3.22 mm test height, the Gemini™ Kelvin test contactor is an excellent all-around spring probe with low inductance, high bandwidth, and excellent current-carrying capacity. The device under test (DUT) side tip design accurately maintains its 100 µm spacing for the life of the probe. Customers report typical probe life of 500 k to 800 k package insertions, or over 2M touchdowns at wafer-level test. The offset tip allows manageable board layout with a board-side spacing of 0.4 mm.Gemini Kelvin probes and contactors provide a first-rate solution that effortlessly makes reliable, true Kelvin contact for high-volume final test of both singulated packages and wafer-level devices. Gemini Kelvin is an ideal solution for devices such as power controllers, A-D and D-A converters, power amplifiers and audio and video circuits.
-
-
Product
Diagnostic Cores
Diagnostic VersaCore™
-
The diagnostic cores are uniquely designed in the VC20™ with Advanced Cantilever™ technology format. Using the customizable PCB, components can be added to create a “golden core” to quickly troubleshoot your system*Test SMUs*Test Motherboard*Test Pogo pins*Test Relay matrix
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UTT 306 x 248 mm
MG-02-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 4 interface blocks of 160 signals• All interface blocks can be customized
-
Product
Semiconductor
-
You can find Spring probes used for test process for production of semiconductor here. Spring probe is probe with spring inside and is also called Double-ended probe and Contact probe. It is assembled in IC socket and becomes electronic path, which vertically connects Semiconductor and PCB. By our excellent machining technique, we can provide spring probe with low contact resistance and long life. “MARATHON” series is our standard lineup of spring probe for testing semiconductor.
-
-
Product
Test Probes
-
Petracarbon is a leading supplier and provider of spring contact probes and semiconductor test sockets.
-
Product
Rugged Connectors
-
Guaranteed for a minimum of 100,000 connections, our rugged connectors are designed to meet your industrial & ergonomic demands in harsh testing environments. We offer numerous connector specifications all fitted with interchangeable spring loaded test probes. Supplied as a single hand held unit, panel mounted or fitted to a test lead, the combinations are limitless. Designed directly from your CAD data and thoroughly tested, our rugged & reliable connectors are used worldwide on a daily basis.
-
Product
Linear Testfixture (Cassette Not Included), UTT 105 x 170 mm
MG-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (1000N) 650 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 105 x 170 mm (wxd)• Outer dimensions: 254 x 400 x 50 x 140 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
Connectors
-
Through our Hypertac, IDI and Sabritec technology brands, we supply application-specific, high-reliability electrical interconnect solutions from highly integrated assemblies to microminiature connectors and spring probe contacts. The core of our advanced interconnect solutions is our contact technologies: Hyperboloid, Tortac, Spring Probe, High Speed, Edge Card, Fiber Optic, EMI/EMP, High Power and High Temperature.
-
Product
Diagnostic Cores
VersaCore™
-
The diagnostic cores are uniquely designed in the VC20 format. Using the customizable PCB, components can be added to create a "golden core" to quickly troubleshoot your system Test SMUs, Test Motherboard, Test Pogo pins, Test Relay matrix.
-
Product
Switch Probes
-
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
Product
Nanotek Brush
Nanotek Series
-
Nanotek Brush is fine stainless wire brush for removing solders or dirt stuck on the tip of spring probe. It has its range of wire diameter from 30µ to 50µ and its fine wire is effective for removing solder or dirt on complicated tip type. We also have Nanotek vacuum, which is nanotech brush combined with vacuum cleaner powered by your compressor or vacuum pump.
-
Product
Linear Testfixture (2 pcs. Cassette Included), UTT 105 x 170 mm (2pcs)
MG-05
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (1000N) 650 units for each cassette• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 105 x 170 mm (wxd) each cassette• Outer dimensions: 550 x 400 x 50 x 140 mm (wxdxh1xh2)• Designed for 2 pieces changeable cassette
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UUT 586 x 248 mm
MG-03-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd)• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
-
Product
For AIM-65 And AIM-75S
8" MSR Module
-
MSR module is suitable for retail customer to do membership card information checking with easy installation wayMSR module is charging via pogo pin
-
Product
Linear Testfixture (Cassette Not Included), UTT 194 x 170 mm
MG-06
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 194 x 170 mm (wxd)• Outer dimensions: 400 x 354 x 70 x 140 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
Socket Phone
-
Design for phone device test and system verify.Phone device: CPU,flash,baseband,LPDDR,power IC.etcPitch range from 0.30 to 1.27mmKey material: PEI,Peek,Torlon,PPS.etcContact with top pogo pin
-
Product
Spring Probes
-
Spring probes are designed to optimize performance in high reliability, multicycle applications. Smiths Interconnect's spring probes, featuring IDI contact technology, are compliant which makes them ideal for blind mate applications as they self correct for x, y, z, rotational and angular misalignment of the target. Offered in compressed heights less than 2 mm and utilized on pitches as tight as 0.4 mm, they are well suited for high density, board-to-board, battery contact and high frequency applications.
-
Product
Hybrid Socket
CSP/Ballnest
-
Any grid size available on 0.50mm pitch or larger. ZIF style socket using Aries solderless, gold plated pressure mount Spring Probe. The gold over nickel plated compression spring probes leave very small witness marks on the bottom surface of the device solderballs.
-
Product
MEMS Spring Probe
-
MEMS Spring Probe is developed by NIDEC-READ original ultra-fine 3D processing technology and enables our customer to supply advanced and innovative test solutions at PCB & semiconductor testing market.
-
Product
Standard Pitch Spring Probes
-
Other than spring probes with gold plating, we have spring probe with anti-solder migration coating and plating that were developed by KITA. We also have anti-solder migration material for plunger tip. These are all included in “MARATHON” series. They have wide range of tip type for various use for every popular total length.
-
Product
PCB Connectors
-
Smiths Interconnect offers a broad range PCB connectors for harsh environments. A wide choice of configurations and terminations of signal, power, high speed, RF contacts and spring probes solutions.
-
Product
Expanding In-Circuit Capabilities
-
Circuit Check supports reading linear bar codes and 2D symbols within each of its fixture product lines.When spring-loaded probes are not practical or access is limited, Circuit Check can help you with thru-connector tests to contact connectors on any surface or edge of a circuit board. These tests can be implemented spring probes, mating connectors, sacrificial SMT connectors, and stabber cards.
-
Product
Custom Pogo Pin Rings & Blocks
-
Reduce your cost-of-test with our pogo pin blocks and interfaces that transform complex DUT boards or breakout boards into universal motherboard-style interfaces. Eliminate the need to purchase or build a new board for every unique device, unit, or package.
