Modulators
Are devices which varies a characteristic of a repetitious electrical or electromagnetic wave of less than infrared frequency in accordance with a characteristic of an arbitrarily varying information carrying signal.
-
product
PXI Fault Insertion Insertion Switch Modules
Our PXI Fault Insertion Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect – all of which can simulate connectivity problems in the system.
-
product
Computing Power VRM/IMVP
Renesas' computing power products are featured with high accuracy up to ± 0.5%, parallel/serial VID supporting, phase dropping, CCM/DEM mode transition for energy saving, and I2C function. Our multiphase modulation technology comes from our experience in analog multiphase controllers used in computing.
-
product
AC/DC - Enclosed SMPS Power Supply
Mornsun Guangzhou Science & Technology
MORNSUN AC/DC enclosed switched-mode power supplies (SMPS) feature complete EMC tests and protections, high efficiency, and wide selection. MORNSUN SMPS withstands 300VAC surge input for 5 seconds. 305RAC (305Vin reliable under all conditions) AC to DC SMPS module is included. 305RAC Series is a collection of AC/DC converters that can run from nominal 85 VAC up to 305 VAC and are safety certified to UL/IEC/EN standards, with CB Reports. These AC to DC enclosed switching power supplies in MORNSUN SMPS Power Supplies portfolio meet IEC/EN61000-4, CISPR32/EN55032, IEC/UL/EN62368, EN60335, and GB4943 standards and are widely used in areas of industrial, LED, street light control, electricity, security, telecommunications, smart home, etc. They comply with the latest global energy efficiency standards. The most high-quality AC to DC SMPS ranging from 15W to 1500W witness the continuous innovation of MORNSUN SMPS power supply family.
-
product
PXI 8-Slot BRIC Matrix, 220x4 1-Pole (5 sub-cards)
40-562B-121-220X4
The 40-562B-121-220X4 is a high density BRIC8 matrix module with a size of 220x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Arduino CAN Shield
IFB-10003-AWP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 58651
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 500 MHz 12-bit A/Ds- Four multiband DDCs (digital downconverters)- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Network Interface Card
XMC477RC
The XMC477RC is a quad switched mezzanine card (XMC) compatible module providing a 4-channel Gigabit Ethernet Small Form Factor pluggable (SFP) interface.
-
product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
product
50 Ohm MMCX to MMCX Cable Assembly
40-977-571-0.1m
This 0.1m long MMCX cable assembly is part of the range of RF cables. Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
PXI 5A Mux 2-Bank 24-Ch Isolated COM
40-651-012
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
PXI 8-Slot BRIC Matrix, 88x8 1-Pole (4 Sub-cards)
40-562B-121-88X8
The 40-562B-121-88X8 is a high density BRIC8 matrix module with a size of 88x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Terminal Block For 34925A Multiplexer
34925T
The Keysight 34925T is a terminal block for the 34925A 40/80-channel FET multiplexer, used for discrete wiring. It supports up to 20 AWG wire size for up to 100 connections or 24 AWG for 100 connections or more. Two terminal block options facilitate wiring connections to the 34925A module.
-
product
PMC Module
PMC-CIV-32LVDS
User Programmable AlteraCyclone IV FPGA 484 BGA:EP4CE30, EP4CE50,EP4CE70 options• Stand alone possibility• Single wide PMC Module• Optional User clock oscillator
-
product
PXI 12-Slot BRIC Matrix, 132x4 2-Pole (3 sub-cards)
40-562B-322-132X4
The 40-562B-322-132X4 is a high density BRIC12 matrix module with a size of 132x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI MUX 4 Banks of 32 Channel 1 Pole
40-610-022-4/32/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
PXI Ultra High Density Matrix, 84x4, 1-Pole, 2A, 60W
40-575A-001
The 40-575A-001 is a high density matrix module able to switch up to 2 A or 300 VDC/250 VAC. It is in 84x4 1-pole configuration and constructed using high quality electro-mechanical relays for high switching confidence.
-
product
Electrical Receiver Conformance Test Application for IEEE 802.3bs/ cd
M8091BSCA
IEEE 802.3bs receiver test application for 200GAUI-4 and 400GAUI-8, covering chip-to-module, chip-to-chip, backplane, and copper cable interconnects.
-
product
PXI Resistor Module 4-Channel 1R to 63.7R with SPDT
40-293-111
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI/PXIe Power Relay Module, 5 Amp, 50-Pin D-type Connector, With Interlock
40-158-103-HI
The 40/42-158-103-HI is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
product
Data Analytics Platform
CISC provides software modules to collect and analyze data from IoT devices. They can easily be integrated into any existing infrastructure. User-friendly reports and visualizations of the data provide comprehensive insight into what is happening in your business. Furthermore, our platform is able to diagnose and even predict failures as well as discover usage patterns or analyze performance.
-
product
PXI High Density Multiplexer, 20-Bank, 4-Channel, 2-Pole
40-615A-002
The 40-615A-002 is a 20-bank, 4-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pinconnector.
-
product
NI TB-2646B Terminal Block for NI 2532B as 1-Wire Quad 4x32 Matrix topology With Column Protection Resistors
782385-14
The TB-2646B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire dual 4x32 or 1-wire quad 4x32 matrix. You can directly connect the TB-2646B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2646B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
TB-2632B , Screw Terminal, PXI Module Multiplexer Terminal Block
781689-01
The TB-2632B provides the necessary routing to configure the NI PXI-2530B PXI Multiplexer Switch Module as a 1-wire 8×16 matrix. You can directly connect the TB-2632B to the front panel I/O connectors of the PXI-2630B. The TB-2632B includes screw terminals to connect signals to the PXI Multiplexer Switch Module as well as screw terminals for trigger input and trigger output signals.
-
product
Medical Computer Equipped With MXM Graphics Module Supporting NVIDIA Quadro® GPU With 8th/9th Generation Intel® Core™ I7/i5/i3 In LGA1151 Socket. Compliant With IEC 60601-1/IEC 60601-1-2
MLB-3000
- Medical grade computer compliant with IEC 60601-1:2005 + A1:2012 + A2:2020 (3.2 edition) / IEC 60601-1-2:2014 + A1:2020 (4.1 edition)- ADLINK MXM Graphics module support (Type A/B, up to 120W)- 8th/9th Gen Intel® Core™ i7/i5/i3, Celeron® processor- Dual SODIMMs for up to 64GB DDR4 non-ECC memory (dependent on CPU)- DisplayPort (2 from CPU, 4 from MXM)- 1x M.2 E key supporting 1630 or 2230 for Wi-Fi/Bluetooth module, 1x M.2 B key supporting 2242 or 2280 for SATA storage module- Reliable Molex type 12V DC-in connector- 1x Intel® i219-LM and 3x Intel® i210-AT
-
product
Analog I/O module with 16 differential analog output channels
IO107
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 16 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
product
4-Channel 1.25 GHz, 16-bit D/A with Virtex-6 FPGA - 6U VPX
Model 57670
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
160 Pin DIN 41612 Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 160-pin DIN 41612 connector.
-
product
ADAQ Data Systems
Atec’s Data Acquisition and Control System (ADAQ™) is a modern, full-featured, highly integrated hardware and software solution that is applicable for use with most commercial and military turbine engine test cell applications. Built upon National Instruments’ respected LabVIEW platform, ADAQ™ is robust, versatile, user friendly, and specifically designed to handle the demanding requirements of engine testing. It links seamlessly to digital engine modules (FADECs, DEECs, EECs, ECUs) as well as legacy analog and mechanical controls. Users can create, remove, calibrate and display channels, as well as generate custom calculations, screens and reports. Beyond the most impressive manual throttle control and operation available, Atec’s ADAQ™ additionally offers the option of fully automated testing.
-
product
USB Module
USB-200
This USB module enables a fast connection of the sensors tothe computer (PC, Mac, XO, or Linux).This module is the first in a chain of sensors connected toa USB port of the PC. It provides both power from the PC to thesensors and communication between the PC and the sensors.
-
product
PXI Prototyping Module, 2-Slot, 78-Pin D-Type
40-225A-402
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
