E1
European digital transmission standard that carries signals at 2 Mbps (32 channels x 64 Kbps).
See Also: HDLC, T1, E3, E1 Testers
-
Product
WAN Tester II
-
The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.
-
Product
DCME Analysis System
-
DCME Analysis System (SCL-DAS) is a software based application, which is designed to classify, process and decompressed the compressed signals transmitted over the satellite links.DCME Analysis System supports most of the commercially available DCMEs including PCM, ADPCM, DX-3000, DX-7000, DTX-600, DTX-360, DTX-240 (D,E,F,T), CELTIC-3G, OKI TC-2000 etc. While processing the compressed/normal E1 carrier, the SCL-DAS provides the processed intelligible output in the form of Voice and Fax along with Originating Point Country, Destination Point Country, Outgoing Number, Incoming Number etc.
-
Product
I/O Modules
-
*Configurable input / output functions*Direct connection of hydraulic valves or joysticks*Modules with M12 connector or central plug*High-performance CAN interface for various communication tasks*E1 type approval (German Federal Motor Transport Authority)
-
Product
New Generation Analyzer For IEEE C37.94
NetProbe 2000 C37.94
-
The NetProbe 2000 C37.94 is a field analyzer with IEEE C.37-94 Multimode optical fiber interface for testing bit error preformance between teleprotection and digitalMultiplexer equipment. Can be combined with many optional interfaces for T1,E1, WiFi, VoIP and V-series testing.
-
Product
2 Port T1/E1/PRI Bulk Call Generator
BCG-2PRI
-
This unit has two PRI ports allowing to generate real calls to a T1/E1/PRI connected device for the stress-test.
-
Product
High Performance Passive Antenna, Waterproof, Wide Operating Temperature Range, IP67 Level
AIW-521
-
Passive antennaIP67-ratedGPS-L1: 1575.42 MHz/GLONASS-G1: 1589.0625 MHz/GALILEO-E1: 1575.42 MHz/BeiDou-B1/B1-2: 1561.098/1589.742 MHzSMA male connectorOperating Temperature: -40 ~ 85℃
-
Product
4 Port T1/E1/PRI ISDN Simulator
SIM-4PRI
-
The most inexpensive ISDN simulator on the market. This unit has four PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
WAN Tester
-
The Telinc WAN Tester is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, modems, multiplexers, CSU/DSUs, T-1 ESF CSUs, DU, NTUs and TIUs.
-
Product
E1 Ethernet cable, twisted pair 1m
182219-01
Ethernet Cable
8-Pin Male Ethernet to 8-Pin Male Ethernet, CAT-5E Ethernet Cable - The 8M-8M Ethernet Cable connects devices to network hubs or switches. The cable has straight-through wiring and is available in different lengths and thin profile options.
-
Product
TestPort Line Of Hand-Held Ethernet Test Equipment
-
The TestPort line of handheld Ethernet protocol test tools represents the state-of-the-art test equipment for telecom backhaul networks. It’s protocol support includes Gigabit Ethernet (GbE), Sychronous Ethernet (SyncE), and E1. Testing applications include protocols analysis, traffic generation, and impairment testing.
-
Product
4 Port T1/E1/PRI Bulk Call Generator
BCG-4PRI
-
This unit has four PRI ports allowing to generate real calls to a T1/E1/PRI connected device for the stress-test. It can be used to generate call volume to VoIP geteways, PBXs, Fax servers, RAS serves.
-
Product
ALL-OUTDOOR RADIO SYSTEM
FreeMile 17/24
-
SAF FreeMile FODU - a new generation license-free 17/24GHz ISM band radio for Ethernet packet data and E1 voice transmission. The new radio system combines excellent features traditionally associated with ISM radios – interference-free operation, high availability, Carrier grade full duplex capacity with no cost of licensing and quick installation. SAF FreeMile radio also offers a user-friendly Web browser based management interface and straightforward installation process to ensure trouble-free experience for any user.
-
Product
10-meter (33 feet) Sensor Cable
E1739B
Calibration Cable
The E1739B 10-meter (33 feet) Sensor Cable is used to connect the E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.Other cable lengths available: E1739A 5-meter (16 feet), E1739C (49 feet) 15-meter and E1739D 25-meter (82 feet).
-
Product
Air Sensor
E1738A
Environmental Sensor
The Keysight E1738A environmental sensor measures air pressure, temperature and humidity. The sensor detects and automatically compensates for operating environment changes when used with the 5530 Laser Calibration System. The result is improved overall system accuracy.
-
Product
Frequency Converter
A6000-E1
-
The Quartzlock A6000-E1 is a 1U rack mount, frequency converter for use with frequency standards such as rubidium, cesium, or hydrogen maser standards. Sine wave outputs are provided at frequencies of 2,048 kHz
-
Product
Emergency Stop Switch [Pushbutton Type]
SG-E1
-
Panasonic Industrial Devices Sales Company of America
Emergency Stop - Push-Button Type Switch.
-
Product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
-
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
Product
PCI/104-Express Quad PCIe MiniCard Carrier
E104-MPE
-
The PCIe MiniCard carrier provides four PCIe MiniCard sockets on a PCI/104-Express form factor board. All four sockets have PCIe x 1 and USB interfaces and support full size and half size PCIe MiniCard modules.
-
Product
Eurocard Plugbord
E160-6U-2
-
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors.Voltage and ground bus around board perimeter on both sides. Bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
Product
25-meter (82 feet) Sensor Cable
E1739D
Calibration Cable
The E1739D 25-meter (82 feet) Sensor Cable is used to connect E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.
-
Product
Cameras for Mobile Applications
-
- Programmable to IEC 61131-3 with CODESYS- Robust metal housing for surface or panel mounting- High-performance CAN interface for various communication tasks- E1 type approval (German Federal Motor Transport Authority)
-
Product
Remote High Performance Receiver
E1709A
Receiver
The measurement signal frequency changes as the stage velocity changes. The Keysight E1709A ensures minimal phase processing errors due to frequency changes. The receiver also provides immunity to errors induced by changes in measurement signal power that occur due to small pitch, roll and yaw movements during stage motion. These features help provide the most accurate measurements under system motion.
-
Product
A-quad-B cable
E1735A-001
-
The A-quad-B cable is a 3-meter cable that connects your machine's A-quad-B encoder output to the E1735A USB axis module's A-quad-B input connector. The cable is supplied with a mating connector for the USB axis module on one end. The other end is un-terminated, allowing you to make the connections you need for use with your machine's encoder.
-
Product
E1 T1 Tester
NetProbe 2000 PDH
-
New Generation Analyzer for Legacy PDH networksThe NetProbe 2000 E1E3 is newest, state-of-the-art handheld analyzer on the market for testing the legacy E1 and E3 in PDH networks. It includes all features for E1 & E3 BERT and E1 physical layer testing. Automated line monitoring performs autocheck of essential alarms and errors.
-
Product
Material Sensor
E1737A
Environmental Sensor
The Keysight E1737A Material Sensor monitors the temperature of an object being measured or of the work piece itself. The sensor detects temperature changes and automatically compensates for thermal expansion errors.
-
Product
Beam Bender BK7, Fixed Horizontal-Bend Mount
E1834M
-
The E1834M is a beam bender that bends the incoming beam at a 90-degree angle and is designed for beam diameters of 9 mm or less. This referenced optics uses high performance horizontal mount to deliver laser beam throughout a measurement system. The 8 flexure feet are designed for stable beam pointing.
-
Product
33% Beam Splitter - BK7, fixed horizontal-bend mount
E1834E
-
The E1834E is a 33% beam splitter in a high performance horizontal mount that offer the high pointing stability for Keysight laser interferometer measurement system. The 8 flexure feet are designed for stable beam pointing.
-
Product
Eurocard Plugbord
E160-3U-1
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides. Pad and bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
Product
Sensor Cable, 5 M
E1739A
Calibration Cable
The E1739A 5-meter (16 feet) Sensor Cable is used to connect the E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.
-
Product
Eurocard Plugbord
E160-6U-1
-
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides.Pad and bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
