Leakage Testers
Look for unintended path of current.
-
Product
Leakage Current Tester and Clamp-On Earth / Ground Resistance Tester
-
10µA Ultra High ResolutionLarge Conductor Diameter (30mm)AC Current in 5 Ranges (40mA, 400mA, 4A, 40A, 60A)Wide Frequency Response (40Hz-1KHz)ACA, ACV, Ω and ContinuityLarge 3¾ Digit LCD (4000 Count)40 Segment Fast Bargraph Display (20 times/sec.)Data Hold and Max / Min HoldRelative Measurement600 Vrms Overload Protection in Resistance Range
-
Product
Non-contact Io/Ior Leakage Clamp Meter
M-340IRV
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Palm size mini clamp type.・High accurate measurement with min. resolution 0.001mA.
-
Product
Clamp on AC Leakage Current Sensors
-
High Accuracy Clamp AC Leakage Sensor use permalloy magnetic cores, with small size, high accuracy, good stability, strong anti-interference ability characteristics. It is applied with double shield technology, which insure strong anti-interference ability.
-
Product
Capacitor Leakage Current/IR Meter
TH2689A
-
Changzhou Tonghui Electronic Co., Ltd.
TH 2689/TH2689A provides max. test voltage: 800v/500v, charge current: 0.5mA─500.0mA( if >100V, the max. power 50W can limit). It is mainly applied in capacitance leakage current, insulation resistance and aluminum electrolysis capacitance anode foil pressure test. Also it can be applied in the confirmation of annihilator, zener diode, neonbulb .etc and leakage current test. Standard Handler interface, stable and rapid test, to reach the sorting effect
-
Product
Multi Circuit Leakage Current Monitor
MCM-8000
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●The leakage current of max.8 circuits at the same time.●Easy for data management (storage by CSV formula)●Cost performance, high-speed sampling with high-frequency cut function.
-
Product
Torsion Testers
10k to 300k in.lbf (1,000 to 30k N.m)
-
For maximum versatility and capability, Tinius Olsen offers a full range of torsion testing machines in capacities from 10,000-300,000in.lbf or kg.cm (1000-30,000N.m). Higher capacity and other longer length models are available on request.
-
Product
Franklin Tester
Model 717
-
The Model 717 Franklin Tester provides a means of testing single strips or punchings of flat rolled electrical steel, for surface insulation resistance under predetermined conditions of voltage and pressure.
-
Product
Qualification Tester
CableIQ
-
CableIQ qualification tester is the first cabling bandwidth tester for network technicians. This Ethernet network cable testergives even the most novice tech the vision to see what speeds existing cabling can support, quickly isolate cabling from network problems, and discover what is at the far end of any cable.
-
-
Product
Peel Testers
-
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
-
Product
Circuit Testers
-
Precision Mastech Enterprises Co.
Portable, handheld electrical tools used to detect voltage, verify electrical power, check for continuity (broken circuits), and test for proper grounding in electrical systems, outlets, and automotive components.
-
Product
Sensor Tester
-
*Connection facilities for DC 2-wire and 3-wire sensors, *Change in switching status signalled visually and acoustically, * 15 V operating voltage for sensors when using a 9 V block battery, * Switches off automatically when not in use, * Visual indicator for operating voltage, switching status and low battery
-
Product
Torque Tester
DIS-IPS series (20CL/5C)
-
For managing various torque wrenches, torque drivers, and automatic/semi-automatic machines. The highly compact detector is ideal for automated line measurements. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. Efficient measurement is possible without unwinding work by "OW joint ".
-
Product
WAN Tester
-
The Telinc WAN Tester is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, modems, multiplexers, CSU/DSUs, T-1 ESF CSUs, DU, NTUs and TIUs.
-
Product
Leakage Current Clamp Mete
-
Basic functions:AC current:20mA resolution: 0.01mA, ± (2.5%, +5)200mA resolution: 0.1mA, ±(2.5%, +5)2A resolution: 1mA, ±(2.5%, +5)60A resolution: 100mA, ±(3%, +8）AC voltage: 600V, ±(0.8%, +5)DC voltage: 600V, ±(0.8%, +5)Special functions:Auto ranging Low battery display Data hold Auto power-off Over-load protection Input impedanceDC voltage measurement: ≥10MΩ Sampling frequency: 3 times/s Maximum display: 1999 Maximum distance between clamps: 30mm General characteristics:Product colors: iron-gray and redProduct net weight: approximately 136gLCD size: 25x36mmProduct size: 183x63x29mmPower: 2x1.5V, 7#Standard accessories: packing carton and handheld bag English user's manual and battery
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
Memory Tester
SP3000
-
CST is proud to offer a portable stand alone and affordable memory tester, combining DIMM and SODIMM testing capability all on the same universal base unit with optional easy plug-on test adapters.
-
Product
Multifunction Tester
COMBI521
-
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Mechanical Testers
-
Actron’s wide variety of mechanical testers includes specialty tools, compression testers, vacuum pressure gauges and advanced timing lights. All mechanical testers work effectively on most foreign and domestic vehicles, small engines, motorcycles and other recreational vehicles to save you time on inspections and repairs.
-
Product
Leakage Current Monitor
LCM500
-
The Doble LCM500 Leakage Current Monitor can measure condition while a surge arrester is still in service, measuring the quality of the metal oxide blocks and helping manage the risk of failure.
-
Product
Insulation Tester
-
Shenzhen Graigar Technology Co.,Ltd.
Testing the integrity of insulation requires measuring its resistance to current flow across it. A high level of resistance means that very little current is escaping through the insulation. Conversely, a low level of resistance indicates a significant amount of current may be leaking through and along the insulation.
-
Product
High-voltage Testers
-
Operational safety and reliability of electrical equipment and cables directly depend on the dielectric strength of the insulation. Portable and mobile high-voltage testers from KharkovenErgoPribor Ltd. are used for acceptance and operational testing of substation equipment and cable lines, as well as for checking the reliability of personal electrical safety equipment. Our testers range is represented by test systems that allow conducting high-voltage tests with DC and AC voltage, testing polymer insulated cables with very low frequency, testing and locating faults in cable sheath, as well as performing the initial burning of insulation on damaged sections of cable lines.
-
Product
Battery Testers
-
Wuxi IMHOO Technology Co., Ltd.
Voltage of batteryBattery type1.5VButton Cell, AA,AAA,C,D,N3V Lithium6V Camera Battery9V 12V 15V 22.5V Power Source Not use batteryWeight 260gmeasurement 100x63x33mmPacking50pcs/CTN
-
Product
Voltage Testers
-
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
Product
Specialty Testers
-
Test Products International, Inc.
TPI specialty testers offer versatility and precision to meet the needs of a variety of jobs and projects.
-
Product
Earth Leakage
-
National Meter Industries Inc.
This new range features a series of improvements intended in particular for installing unitson switchboards. Along with the usual attachment elements, this unit can be installed onDIN rails using an accessory, which facilitates its installation.
-
Product
Polarization Tester
-
Polarization Tester is used to measure the stress value of optical glass, glass products and other optical materials, and is widely used in pharmaceutical companies, glass products factories and laboratories.
-
Product
Mini AC Leakage Current Clamp Tester
M-102+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・23mmφCT window and ultra compact size.・Data-hold function. Especially useful when working in dark or hard to get areas.
-
Product
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
782015-02
Multifunction Cable
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
-
Product
Non-contact Io/Ior Leakage Clamp Meter
MCL-800IRV
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Available direct voltage input at live part as ordinary.・Calculable insulation resistance value（MΩ）by voltage & current (only in case of using direct voltage input sensors)・Available measurement for 3P/4W star connection.
