Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Ethernet, GPIB And USB To Serial Interface Board
ICS's Model 9006 is a multi-interface to serial board that adds Ethernet, GPIB and USB interfaces to serial devices or older instruments. Use with an embedded processor board to create smart instruments with multiple interfaces. The 9006's Ethernet port is VXI-11 compatible for easy control by the following computer systems without special drivers: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. VXI-11 is one of the 9006's Ethernet protocols. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
product
SparkFun Load Sensor Combinator
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat's nest of wires. The Load Sensor Combinator was created to combine the 12 wires found in a bathroom scale into the standard four-wire Wheatstone bridge configuration.
-
product
SF6 Decomposition Products Detector
JH4000A-4
Xiamen Jiahua Electrical Technology Co.,Ltd
JH4000A-4 SF6 Electrical Equipment Decomposition Products Detector is a high precision, intelligent and portable device, able to make judgment rapidly and correctly based on the content of main decomposition products of insulation materials inside the SF6 electrical equipment like SF6 circuit breaker, instrument transformer, GIS and transformer. It detects SO2+SOF2, H2S, CO and HF. It is reliable, accurate and stable. Inspected by authorities such as the National Institute of Metrology, the device, having excellent performance, complies with relevant international and national standards. It is a product recommended for use by the State Power Grid Company. Decomposition products detection provides reliable evidence for the internal fault diagnosis and it is an effective measure for preventive and corrective maintenance.
-
product
Subsea Pipe Detection & Tracking System
HydroPACT 440
The HydroPACT 440 pipe detection system has been established for a number of years as the industry standard, providing accurate and reliable survey data, which provides the position of conductive assets on or beneath the seabed. The system is flexible in its range of uses and can be installed on a variety of vehicles for undertaking survey work.It provides a reliable and simple method for performing accurate submarine surveys on a conductive target such as a cable or pipe.
-
product
Alligator Clip Leads
U1781A
The Keysight U1781A is to be used with the U1700 Series Handheld Capacitor and LCR meters. These clips are shipped as standard with every handheld capacitor or handheld LCR meter.
-
product
Antenna, Biconical
EM-6917B-1 | 30 MHz To 3 GHz
The EM-6917B-1, a hybrid combination of the industry standard biconical and log periodic antennas, delivers an unmatched combination of frequency coverage and high power handling capability. Featuring exceptionally broad frequency coverage of 26 MHz to 3 GHz, the EM-6917B-1 eliminates the need for adjustments or switching antennas in most test applications up to 3 GHz, and it does so without compromising power handling capability for transmit applications.
-
product
LED Power Driver Test System
Chroma C8000
Chroma Systems Solutions, Inc.
The Chroma 8491 ATS is equipped with optimized standard test items for LED driver testing (lighting & TV backlight). The user is only required to define the test conditions and specifications for the standard test items to perform the test.
-
product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Bias Ball Probe
POGO-1T-4-S
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Perten Falling Number 1310
The Falling Number (FN) method is a fast and easy test to determine alpha-amylase activity in order to detect sprout damage. The Perten Instruments FN method is the World Wide Standard for measuring alpha-amylase activity in both flour and meal of wheat, durum, rye, barley, other grains and malted cereals.
-
product
Small Drop Test System
KRD41 series
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
product
Minigrabber® Test Clip With Banana Jack.
4723
Minigrabber? test clip with banana jack, available in ten colors. This Minigrabber test clip has a standard banana jack built right into the plunger. Excellent for attaching the Grabber test clip directly to the end of a banana plug patch cord.
-
product
eXpert FPGA DSP Features for Data Acquisition
GaGe provides several eXpert FPGA processing firmware options for use with CompuScope Digitizers. All standard default CompuScope Digitizer model configurations can store raw acquired waveform data to onboard sample memory and then transfer them quickly to the user for analysis, display and/or storage. The addition of optional eXpert FPGA processing firmware features allow for some signal processing analysis, or other specific functionality, to be performed on the digitizer hardware itself within its onboard Field Programmable Gate Array (FPGA).
-
product
PXI-5402, 14/16-Bit, 20/40 MHz Arbitrary Function Generator
779655-01
20 MHz Bandwidth, 14-Bit PXI Waveform Generator—The PXI‑5402 is a 20 MHz function generator capable of generating standard functions including sine, square, triangle, and ramp as well as other signals like psuedorandom noise and DC signals. This function generator can generate signals from -5 V to +5 V and uses direct digital synthesis (DDS) to precisely generate waveforms.
-
product
Cement Compression & Flexural Testing Machines
The Compression & Flexural testing product line from Qualitest offers a wide variety that will fit almost any budget. Different options between models include digital or analog display, single or dual range, and different types of configurations. All the Compression & Flexural testing machines conform to international standards for compressive & flexural tests.
-
product
Area Scan Camera
Area Scan Cameras provide high-performance and high-resolution options that offer excellent image quality and many sensor options. They can connect over a variety of interface standards such as USB3 Vision, GigE Vision, and Camera Link. Models offer high frame rates and rolling or global shutters. Area Scan Cameras are well suited for a variety of applications, such as automated inspection, smart machine control, and factory automation.
-
product
Electric Burn-in Board Carts
Conforms to SEMI ergonomic standards Holds and transports card cages for semi-automatic loading/unloading. Holds up to 10 burn-in boards. Raises and lowers the burn-in boards for easy loading/unloading of boards into ovens or onto test benches. Cart can be adapted to dock with any Micro Control oven.
-
product
Motorized Test Stands
Imada offers basic and advanced motorized test stands that are available in Standard, High, and Low speeds.Use ZTS or ZTA force gauges with MX, MX2 or EMX Series test stands to enable force control and non destructive testing.
-
product
Omnidirectional Sound Source
DS3
The Dodecahedron Speaker Set offers a lightweight, yet powerful signal source for room & building acoustic measurements. The optimized frequency response ensures precise measurements in accordance with the ISO 16283 and the ISO 3382 standards. The set includes the robust omnidirectional DS3 odecahedron Speaker and the remote-controlled PA3 Power Amplifier. Equalized acoustic frequency spectrum from 100 Hz to 8 kHz.
-
product
SDI Cable Drivers
Macom Technology Solutions Holdings Inc.
At MACOM we offer a wide range of products specifically designed for driving Serial Digital Interface (SDI) video signals across long copper cables. These multi-rate products are the ideal solution when designing high definition (HD) and ultra high-definition (UHD) video broadcast equipment and are fully compliant with the Society of Motion Picture and Television Engineers (SMPTE) standards.
-
product
PXI SPST Switch: 50-ch, 100Vrms/1A, Reed Relays
M9132A
The M9132A is a high-density, general purpose switch with50 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or standard cable connections.
-
product
Digital Attenuators
Compact microwave digital step attenuators with low insertion-loss, USB control and power, 60 or 90dB max setting, 0.25 or 0.5dB step size, ranging from 10MHz to 24GHz. Front OLED display and user control buttons standard.
-
product
Automation And Validation Of ECU Tests
ECU-TEST
Softing Automotive Electronics GmbH
Automotive Electronics - ECU-TEST is the universal test automation ECU-TEST was designed for test automation and for the validation of ECUs. Standard test tools are already integrated and can be used together in tests. ECU-TEST is used to design, realize, run and evaluate tests.
-
product
Ozone Test Chamber
EKT-2001OZ-HCSSX
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
product
Fixed-Point C6455 DSP Module
FMC645
Sundance Multiprocessor Technology Ltd.
The FMC645 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6455 device. The FMC645 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), has a high-pin count connector and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces.
-
product
Shock Impact Testing
Environment Associates provides everything you need in drop shock testing — package/container, drop shock/impact systems and electro-dynamic simulated pulses. With our equipment, we specialize in tuned, matched impacts from 20 Gs to 30,000 Gs and from 30 ms to .02 ms in sine, saw-tooth, square-wave, gunfire and rotational cam pulses for almost any set of standards, or for any real-life condition. We can also handle a large range of weights and sizes. EA’s specialists will match the right test, equipment and configurations to your product. We also provide fixture design and special set-up solutions to mount and monitor your product’s functionality during and after testing.
-
product
Omnidirectional Sound Source
OmniPower
OmniPower Type 4292-L is an omnidirectional sound source, intended to be used in acoustical measurements for which a uniform spherical sound radiation is required.OmniPower complies to the ISO 3382, ISO 140 and DIN 52210 standards, and is used in both room acoustics and building acoustics applications.
-
product
Universal Test Machine Stands
FTUS
Portable, adjustable height, stands are available for all FTU chamber models. They support the chamber without transferring weight to your testing machine. Standard Universal Test Machine stands are furnished with an 18 inch, electrically actuated, lift system, four swivel casters with locks, and an all welded frame. Four types of stands are available
-
product
Automatic Hysteresis Graph Test System
DX-4DMT
X-4DMT automatic hysteresigraph system accords with the standard permanent magnet test system, GB3217-92, used to measure the major and minor hysteresis loops, demagnetization curves, recoil hysteresis loops and initial magnetization curves in different temperature of ferrite, AlNiCo, SmCo, NdFeB and quenched material, and gives the magnetic parameter, Br, Hcb, Hcj, (BH)max, Hk and so on, and could meet different requirements on test function, precision, power capability, reliability, efficiency, price, local environment from laboratory to enterprise's production line.
-
product
Powered VXS Crates
VXS - "VME-bus switched serial" is the new ANSI / VITA 41 standard which combines the 32-bit parallel VME-bus with high speed switched serial interconnect fabrics in order to increase the data transfer bandwidth to several GB/s.
