Filter Results By:
Products
Applications
Manufacturers
-
product
Millimeter Wave Continuously Variable Waveguide Attenuators
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
product
RF Detectors for Millimeter Wave
RF Detectors are essential microwave/millimeter wave products for most Tx (transmit sources). Transmitter output power measurement is the main application. It is essential to know the RF output power because the output power level must not go above values set by FCC regulations.The unit of power is the watt for RF detectors. But, most commonly used in most RF and wireless systems to express power is the terms of dBm or decibels related to 1 mW:View more RF Detector
-
product
Millimeter Wave Converter
ZVA-Z Series
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
product
Waveguides
Learn about waveguides at Precision MMW. This is a handy waveguide tutorial for the everyday mmWave engineer.Learn more on Waveguides at Precision website here.
-
product
Waveguides
CAES offers a full range of rectangular (WR-22 to WR430) and double-ridge (WRD-180 to WR430) waveguides covering frequency bands from a few hundred MHz to 100 GHz.
-
product
Waveguide Circulator/Isolator
RF Lambda’s waveguide circulators are typically used to prevent unwanted reflections. They offer low insertion loss and high isolation and are available in a variety of frequencies and power levels.
-
product
Waveguide Adapter
Waveguide adapters in a variety of waveguide standards / flange types and coaxial connectors
-
product
Waveguide Adapter
RF Lambda’s waveguide adapter product line is used to convert a waveguide interface to a coaxial interface. They come in a variety of frequencies, connector options and materials. They offer low insertion loss and VSWR as well as high power handling.
-
product
Waveguide Probes
We are a leading Manufacturer & Exporter of Waveguide Probes such as Tunable Probe and Waveguide Matched from India.
-
product
Waveguide Bandpass Filters
More details on PE-W28F001 WR-28 band pass wave guide filter can be found on the the waveguide bandpass filter design datasheet specifications up above. WR-28 waveguide bandpass filter from Pasternack is in stock now at our Irvine, CA facility. Our waveguide bandpass filter with WR-28 flanges is part of over 40,000 components for RF, microwave and millimeter wave applications in-stock which are available to ship same day worldwide.
-
-
product
Waveguide Power Sensor
Make accurate and reliable measurements in the 50 to 110 GHz frequency range. Keysight's waveguide power sensors offer best SWR, high reliability and low loss, and come with a 50 MHz calibration port to reduce measurement uncertainties.
-
product
Double Ridged Waveguide Horn
DRH10
Frequency range: 740 MHz - 10.5 GHz VSWR (MAX): < 1.8:1Impedance: 50 O (Ohm)Connector: N femalePower (CW / Peak): 150 W / 250 W
-
product
Waveguide Accessories
Designed with our leading waveguide development expertise and application knowledge, CAES Waveguide accessories are offered in a variety of options, sizing and materials.
-
product
Waveguide Power Sensor
V8486A
The V8486A waveguide power sensor measures average power over the frequency range 50 GHz to 75 GHz and power range -30 to +20 dBm.
-
product
RF Waveguide Load
RF Lambda’s waveguide loads are used at end of an RF signal chain to provide a good 50ohm match and dissipate any RF energy into heat. They are available in a variety of power levels and offer low VSWR.
-
product
Waveguide Switches
Waveguide switches are electromagnetic switches with hollow circular or rectangular cross-sections and are used for routing RF energy in microwave communications, broadcasting, and in radar applications. Waveguide switches can be used to transfer both power and communication signals, and the bandwidth of a waveguide is in relation to its size, and thus always referred to by its size (e.g. WR112, WR90, WR75 etc.). Compared to coaxial switches, waveguides can route extremely high power signals over a narrow bandwidth at low to high frequencies, and now Lightweight Waveguide series is available.
-
product
Double Ridged Waveguide Horn
QRH11
Frequency range:730 MHz - 11 GHz VSWR (max): < 2.4:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 100W / 170 W
-
product
Double Ridged Waveguide Horn
DRH18-EX
Frequency range: 800 MHz - 18 GHz VSWR (AVG): < 2.4:1Impedance: 50 O (Ohm)Connector: SMA female Power (CW / Peak): 100 W / 170 W
-
-
product
Double Ridged Waveguide Horn
DRH20E
Frequency range: 1.6 GHz - 20 GHz VSWR (max): < 1.5:1Impedance: 50 O (Ohm)Connector: SMA female Power (CW / Peak): 50W / 100 W
-
product
Waveguides
Waveguides from Fairview Microwave consist of coaxial adapters, bandpass filters, bends, flexible waveguide cables, waveguide gain horns, sections and terminations. Fairview waveguides are available in standard sizes from WR-430 through WR-15 depending on type of waveguide product, which encompasses frequencies from 1.7 GHz to 75 GHz.
-
-
product
Millimeter Wave Amplifiers
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
-
product
Fixed Attenuator (Waveguide)
RF Lambda’s fixed waveguide attenuators are used to attenuate RF signals with a waveguide interface. They come in a variety of different frequencies and power levels depending on the application.
-
-
product
Waveguide Loads
Smiths Interconnect offeres high power Waveguide loads that can with stand up 200Watts at 18 GHz
-
product
Double Ridged Waveguide Horn
H-A50
Frequency range: 33 GHz - 50 GHz VSWR (max): < 1.35 :1Impedance: 50 O (Ohm)Connector: 2.4 female Power (CW / Peak): 10 W / 20 W
-
product
Double Ridged Waveguide Horn
DRH110
Frequency Range 14 GHz - 110 GHz VSWR (AVG) <2.1 1:1Impedance 50 WConnector 1.00mm female Power (CW / Peak): 4 W / 8 W
