Filter Results By:
Products
Applications
Manufacturers
HF
High Frequency operating at 3–30 MHz.
-
product
VECTOR-GUN HANDHELD DIRECTION FINDING ANTENNA SYSTEM
HFDF
National RF's Type HFDF active directional antenna system consists of a high gain RF amplifier coupled to a tunable Faraday shielded loop antenna. Several loop antenna assemblies are available to provide coverage of frequencies in the HF and low VHF spectrum. Due to the nature of a Faraday shielded loop, the antenna exhibits a sharp null through the diametric center of the loop. This null is used to determine the direction of incoming radio signals or to locate electrical noise being radiated from some source. The internal high gain amplifier is used to compensate for the inherent inefficiency of the actual loop at the operating frequency. Overall, the system dynamic response is about +6 dB as compared to the dynamic response of a dipole. To aid in the direction finding process on strong signals, an internal 30 DB attenuator is provided. As the loop antenna presents a bi-directional response, tri-angulation may be required to eliminate the ambiguous signal direction. The line of site of the incoming signal is determined by listening for a signal null on the receiver or by watching the receiver’s S-meter.
-
product
Advanced Design System (ADS) Core
W2200BP
Advanced Design System (ADS) is the flagship product from Keysight EEsof EDA, the technology and innovation leader in high-frequency, mixed-signal electronic design automation (EDA). It is the only design simulation platform that enables the co-design of IC, package and board in high-frequency and hi-speed applications. ADS seamlessly integrates system, circuit, and full 3D electromagnetic simulation with Keysight's test instrumentation to perform single pass successful electronic designs repeatedly.
-
product
Pitot Tube Flow Meter
PTFM-1000V2
The Pitot Tube Flow Meter, PTFM-1000V2 is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers to accurately measure highly pulsating exhaust flows with a sampling rate of 1kHz. This rapid capture rate ensures that any pulsations or exotic behaviour in an engine is measured, and the unique design of the PTFM pitot tube means reverse flows can be measured with the same guarantee of sensitivity. The interface can be run standalone with a laptop, or seamlessly integrated to run alongside an analyser system without adding any more steps to the test cycle process.
-
product
Array Solutions OCF
Series Dipoles
Thank you and congratulations on your purchase of the Array Solutions, OffCenter Fed HF Dipole Antenna System. This antenna was built with the same quality workmanship and attention to detail as our military, government and commercial wire antenna products. It is ideal for ARES/RACES, MARS/CAP, USCG Aux., Red Cross, Salvation Army and other disaster and relief organization use. It is built especially for high duty cycle, harsh environmental applications. The use of the finest quality components available and our “overbuilt” quality construction means your new antenna will last for years under the most difficult conditions, while requiring little or no maintenance.
-
product
Signal Generators, Arb.
Function and arbitrary signal generators in the LF and lower HF range up to 500 MHz, generation of standard signals (sine, square, triangle...), fixed and user-definable arbitrary signals; Modulations, Burst, Sweep
-
product
Partial Discharge Measuring Equipment
Electro Mechanical Enterprises
Partial discharge instruments have two modes of Wide Band and Low Frequency. You can use it for Partial Discharge tests of High-Voltage Equipment, Insulation Materials, High-Frequency Equipment, and Power Semiconductor devices. Partial discharge Measuring Equipment can easily realize the test of Partial discharge on print-circuit boards, connectors, semiconductors, small motors and other insulation materials, to make a judgment on good / bad of them
-
product
Resistive Components
Diamond is the best thermal conductor on earth. Combined with a low dielectric constant, it is an excellent RF dielectric material for high-frequency applications in which thermal performance is equally critical. By applying cutting-edge thin film process and extensive millimeter wave design experience, Smiths Interconnect has created a high-performance line of resistive components. The resulting products, our Diamond RF Resistives® resistors, terminations, and attenuators, are significantly reduced in size and unparalleled in average and peak power handling.
-
product
Dissolved Oxygen Monitor in Low Concentration
HD-960L
High stability measurement dissolved oxygen in low concentration HF. Automatically switches between three measurement ranges from μg/L to mg/L. Measurement range : 0 - 20.00 mg/L.
-
product
High-Frequency Test Coil
West Coast Custom Designs, LLC
is most commonly used by the neon industry for detecting leaks in a pumping system; the spark generated by the coil via the solid tip, will enter the tube through the leak and become bright white at the point at which it enters.
-
product
Microtester Test Systems
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
product
ElectroPuls
With more than ten years of running tests over billions of cycles, ElectroPuls systems are the established materials testing instruments using patented linear motor technology. Offering slow-speed static and high-frequency fatigue testing, this versatile testing capability means ElectroPuls systems are ideal for any lab or office space. Choose from axial only or combined axial-torsion systems that can deliver up to 10kN and 100Nm. Available in 3 sizes, simply pick the one that's right for you. ElectroPuls, a simpler, smarter, safer way to meet your testing needs.
-
product
Mini Receiver
FB7-NX
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
product
Passive Probe, 10:1, 500 MHz, 1.2 M
N2843A
The Keysight N2843A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.
-
product
Rubidium Generator
SRO-100
Rubidium generators SRO-100 are designed to generate and output to the consumer highly stable, high-frequency, spectrally pure sinusoidal signals with a frequency of 5 or 10 or 15 MHz.
-
product
RFID Sensor Transponder (HF)
TELID®200
With the TELID® 200 range, you can have a combination of RFID transponders and sensors for measuring physical quantities. Here, in particular, pressure, acceleration, strain, moisture, and electric conductivity are of significant interest. Determining the situation just-in-time and storing the newly measured values in the integrated memory is one of its main functions. More complex functions such as digital I/O ports for connecting memories, microcontrollers and digital subsystems are also available. TELID® 200 products do not require batteries and work with no internal energy source.
-
product
Signal Generator High-Frequency GSM AXIe
The hardware-software complex "High-frequency GSM signal generator AXIe" is designed to generate harmonic sinusoidal signals with analog modulation (AM, FM, PM, IM) or without modulation in the frequency range from DC to 10 GHz.
-
product
FT-NIR Analyzer
ASP400 series
The TALYS ASP400 series analyzer is designed to achieve monitoring and control of continuous processes. Its seamless installation enables real-time process monitoring, determination of stream properties or physical qualities, process characterization and early troubleshooting. This analyzer is suitable for a wide range of refinery process monitoring applications including naphtha conversion units such as catalytic reforming, isomerization, naphtha hydro-treating and steam-cracking as well as applications in HF alkylation, gasoline blending and LPG.
-
product
Active Voltage Probes
Engineers must commonly probe high-frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. Active voltage probes feature both high input R and low input C to reduce circuit loading across the entire probe/oscilloscope bandwidth. With low circuit loading, and a form factor that allows probing in confined areas, the active voltage probe becomes the everyday probe for all different types of signals and connection points.
-
product
Hydrogen Frequency & Time Standard
CH1-1006
The hydrogen frequency and time standard Ch1-1006 is designed to generate highly stable, high-frequency, spectrally pure sinusoidal 5, 10, 100 MHz and pulsed 1 Hz signals and for the behavior of time-frequency measurements.
-
product
HF test adapter
High-frequency test adapters (HF adapters) from INGUN are designed as a replacement set system, consisting of a manual test adapter (MA 21xx and 32xx series) and a high-frequency shielded replacement set from the ATS MAxx/HF series.
-
product
LXI Microwave Multiplexer, 50Ω 36-Channel 1-Bank 4GHz BNC
60-891-001-002
The multiplexer has an extremely high level of performance with low VSWR, very high isolation, low loss and high power handling. It is ideal for switching 50Ω systems for HF up to microwave frequencies. It occupies 2U of rack space, providing a compact switching solution.
-
product
HF Communication Equipment
MS 2000
The Meltronics HF/SSB system provides a reliable voice communication over 2 to 29.99MHz frequency range and is designed to meet the most diverse requirements. The HF system is used to establish communication between Air to Ground station, Air to Air and Air to Ship. This System is suitable for Aircraft, Helicopter and Ships communication applications. The HF transceiver has beyond line of sight communications providing both voice and data services. Systems is a digital, Microprocessor controlled, synthesized unit that utilizes DSP technology to increase performance and versatility.
-
product
Switch Matrices
Configurable, high performance, non-blocking RF switching matrix units from HF to SHF
-
product
Switches
Whether you are performing high-accuracy, low-speed measurements on a dozen test points or high-channel, high-frequency characterizations of integrated circuits, National Instruments delivers a flexible, modular switching solution based on PXI or SCXI to help you maximize equipment reuse, test throughput, and system scalability.
-
product
PXI-2554, 2.5 GHz, 75 Ω, 4x1 PXI RF Multiplexer Switch Module
778572-54
2.5 GHz, 75 Ω, 4x1 PXI RF Multiplexer Switch Module—The PXI‑2554 is ideal for use in video RF applications where high-frequency video signal reflections can damage the source. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
Track and Hold Data
Track and hold amplifiers are used to expand the bandwidth and/or high-frequency linearity of high-speed A/D conversion and signal acquisition systems. Track and Hold Amplifiers can be used in various applications including RF ATE Applications, Digital Sampling Oscilloscopes, RF Demodulation Systems, Digital Receiver Systems, High Speed Peak Detectors, Software Defined Radio, Radar, ECM & ELINT Systems and High Speed DAC De-Glitching.
-
product
Voltage Meter
MN3I
М-module МН3И is a mezzanine module designed to measure the instantaneous voltage value of high-frequency signals via 3 galvanically isolated channels from each other, control circuits and crate frame.
-
product
Antennas
The CAES Antennas portfolio encompasses virtually the entire radio frequency spectrum, from the HF Band, where wavelengths dwarf buildings, to the millimeter wave band, where thousandths of an inch make all the difference, and offers unparalleled product diversity with an extensive product line of advanced antennas and antenna arrays.
-
product
Universal Preamplifier 14
UP14
For Two Dimensional Magnetic Recording (TDMR) and Heat-assisted Magnetic Recording (HAMR) Headamplifiers. Universal Preamplifier 14 (UP14) is designed for TDMR and HAMR Head Amplifiers. With new Guzik RWA4000 TDMR, UP14 allows to process signals from three Read Channels. It also supports two high speed data channels for Write data and Laser data. UP14 has two channels for dynamic TFC control and allows to program TFC power per sector and close loop TFC power control in each channel. UP14 can generate two programmable modulation signals for write data and laser data with bandwidth up to 20 MHz. UP14 consist of two boards. The first UP14 RW Board processes high-frequency signals: read-back signals, write data and laser data. The second UP14 Control Board provides power, control and low-frequency signal generation: TFC, write data modulation and laser modulation.
-
product
Rotatable Directional HF Antennas
Kratos Defense & Security Solutions, Inc.
Kratos’ horizontally polarized rotatable log-periodic antennas are constructed with wire radiators supported by a strong and unusually lightweight support structure.
