HF
High Frequency operating at 3–30 MHz.
-
Product
Test System
NFC Xplorer
-
The CISC NFC is a compact, high-quality test system, developed for HF RFID and NFC devices measurements and performance and conformance tests.
-
Product
Amplifiers
-
Gigacom supplies custom amplifiers to several Test Ranges to support on going test programs. We have experience designing solid state amplifiers operating at power levels up to 1KW and from HF to X-Band.
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - PCIe
Model 78621
-
Model 78621 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A multichannel, high-speed data converter withprogrammable DDCs, it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkey solution.
-
Product
Bench Power Supply, Single, Adjustable, Fixed, 1 Output, 13.3 V, 14.5 V, 15 A
72-8110
-
The 72-8110 is a compact switch mode Power Supply features a very compact footprint that makes it an ideal match for portable communications equipment. Its 50% duty cycle surge rating is comes in handy in demanding transmitting situations. It is also perfect for two-way radio (including HF) and audio equipment including auto sound and multimedia systems. This fixed voltage switch mode power supply is designed with high RFI stability and is especially suitable for two-way radio and communications equipment. Constant current circuitry is used for overload, short-circuit and over-temperature protection. Output current and voltage drop to a safe level when any fault occurs. This power supply also has over voltage protection to prevent connected equipment from damage.
-
Product
HF test adapter
-
High-frequency test adapters (HF adapters) from INGUN are designed as a replacement set system, consisting of a manual test adapter (MA 21xx and 32xx series) and a high-frequency shielded replacement set from the ATS MAxx/HF series.
-
Product
USB Digital Storage Oscilloscope, 1GS/s, 200MHz BW, 10K/channel
TS2202E
-
USB powered 2 channels (stackable up to 12 channels) 1 GS/s real-time sampling 200 MHz bandwidth 10K (TS2202)/64M (TS2212) points per channel Vertical offset adjustable Edge, External , Width, Video/TV Trigger B-Trigger, Delay, Logic, Runt, Serial Bus, Setup/Hold, Slew, Timeout Trigger (TS22x2A Only) LF reject, HF reject, Noise reject RUN/STOP hardware button Export data to WORD, EXCEL, TEXT, HTML, MATLAB etc. Data Logger (HD storage) Embedded 2-channels FG with Modulation, Sweep, Burst function
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - PCIe
Model 78751
-
Model 78751 is a member of the Onyx® family of high performance PCIe boards based on the Xilinx Virtex-7 FPGA. A multichannel, high-speed data converter with aprogrammable DDC, it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkey solution as well as a platform for developing and deploying custom FPGA processing IP. It includes two A/Ds, two D/As and four banks of memory. In addition to supporting PCI Express Gen. 3 as a native interface, the Model 78751 includes a general purpose connector for application-specific I/O.
-
Product
Ultrasonic Rotary Mechanisms For High Speed Testing Of Round Bar And Tubular Products
ECHOMAC® ULTRASONIC ROTARIES
-
High-speed Ultrasonic (UT) Systems enable a full volumetric examination of materials and are designed to detect surface, subsurface, internal and dimensional flaws. This type of testing utilizes high-frequency sound waves that are transmitted throughout the material being tested in order to conduct a thorough inspection.
-
Product
Artificial Power Supply Network
KH3763
-
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
Product
Autotuner
HF-AUTO-R
-
The Palstar HF-AUTO-R is the full-function remote control unit for use with the HF-AUTO automatic antenna tuner. The HF-AUTO-R allows for remote operation of the HF-AUTO base unit up to 500' away and duplicates all buttons, controls, and display info.
-
Product
Low Pressure Drop Thermal Mass Flow Meter
HFM-200 LFE
-
The HFM-200 LFE Series by Teledyne Hastings can be configured and accurately measure gas flow in a broad array of applications. Featuring reliability and stability, the 200 Series is chosen by users for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow meter compatible with most gases.The HFM-200 LFE meter has flow ranges from 0-10 sccm to flows of 0-15,000 slm; provides analog outputs, and is constructed of stainless steel. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Cleaning for oxygen service is available. Our laminar flow elements (smooth, threaded or flanged) are available in various sizes from 3/8" up to 8". Low pressure drops at full scale flow.
-
Product
Perseus SDR HF Receiver
-
PERSEUS is a VLF-LF-HF receiver made by Microtelecom is based on a outstanding direct sampling digital architecture. It features a 14 bit 80 Ms/s analog-to-digital converter with an exceptional 76 dB SNR (BW = 40 MHz), an high-performance configurable FPGA digital down-converter with an up to 1 MS/s output sampling rate and a 480 MBit/s, high-speed USB 2.0 PC interface. Unlike in lower class direct sampling receivers, the PERSEUS RF analog front-end has been carefully designed for the most demanding users and includes a 0-30 dB, 10 dB steps attenuator, a low-loss 10 bands pass-band RF preselector filters bank, and an high dynamic preamplifier with a top-class input third-order Intercept Point of more than 30 dBm. The resulting third-order dynamic range is 103 dB for SSB signals (2.4 KHz BW) and 107 dB for CW signals (500 Hz BW).
-
Product
Mass Flow Controller for Medium Flow
HFM-201 / HFC-203
-
The HFM-201/HFC-203, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-201 / HFC-203 meters and controllers have flow ranges from 0-25 slm to flows of 0-1000 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Many corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
Natural Cooling Input 380VAC 3 Phase to Output 190-300VDC 10A-40A Rectifier Battery Charger
SD230D20ZZ
-
Zhejiang Sandi Electric Co., Ltd
SANDI “SD” series intelligent high-frequency switch power supply modules are specially developed to meet the demands of modern DC system. The charger rectifiers are designed with world leading patent technology “resonant voltage type soft switching power supply technology”. They feature high efficiency and stability, intelligent control, small size and light weight. Standard RS-485 interface, easy to connect with automation system. “Four remotes” functions, intelligent management. The products are widely used in power plant, substations and etc..
-
Product
Concrete / Soil Wall Moisture Meter
-
This is a precision instrument adopting HF electromagnetic waves to measure the moisture content ratio without damaging the object under test. It can be set depending on different building material to raise its measurement accuracy.
-
Product
Flexible Pitch GND Fixture Clamps
GF-A
-
High Power Pulse Instruments GmbH
*Compatible with GGB picoprobe model 10 replacement probe tips*<1 ns rise time (200 ps possible with 5 mm GND wire length)*Custom selectable GND wire length 5-15 mm*Gold-coated spring-steel clamp with micro-machined groove for locking of the clamps on the probe tip*High conductivity and low inductance copper HF litz wire with 200 x Ø 0.02 mm strands*Easy to use clamping*Tungsten carbide probe needle with 1 inch length, 15° taper and 7.5 µm tip radius
-
Product
Gas Flow Sensors
ESRF-HF Transmitter
-
The ESRF-HF is a family of mass flow transmitters which enable fast and accurate measurements of gas flow over a wide dynamic range. Each transmitter integrates a MEMS flow sensor and readout electronics inside a housing with very small form factor made from stainless steel. The duty pressure of the flow transmitter is 11bar. All measurement data are fully calibrated, and temperature compensated on board, leading to a reduced temperature coefficient and high measurement accuracy.
-
Product
Fast Response Flow Controller for Medium Flow
HFM-301 / HFC-303
-
The HFM-301 / HFC-303 meters and controllers have flow ranges from 0-25 slm to flows of 0-1000 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a choice of elastomers and high pressure options, the HFM-301 / HFC-303 services a wide variety of applications. Cleaning for oxygen service is available.
-
Product
Inductive Sensor
HFCT Ø 30-39-50mm
-
Techimp HFCT is an inductive sensor for partial discharge measurements. It is suitable for on/off line PD tests on many electrical systems (cables, transformers, rotating machine, etc..). It has to be applied to the ground connection of the system to be tested.
-
Product
OTP-Based Test System
Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
Electrolytic Capacitor Tester
HF2686C
-
Test voltage: 0-200V/0-500V• Output current range: 0.1μA-30mA• Maximum charge current: 200mA ±10%• Charge time: 0.5s/1s/2s/3s/4s/5s/7s/10s/30s/60s• Accuracy: ±2%
-
Product
Autotuners
HF-AUTO
-
The Palstar HF-AUTO 1800 watt automatic antenna tuner covers 160 to 6 Meters with a power rating of up to 1800 watts PEP. Hams have enjoyed the benefits of low power auto-tuners for years, but now Palstar takes it to the next level and offers auto-tuning with a power rating of 5 Watts to 1800 watts.
-
Product
Cryogenic Probe Station
EMPX-HF
-
The Lake Shore EMPX-H2 probe station enhances standard probe station capabilities with the addition of a ±0.6 T horizontal field electromagnet. All standard C-V, I-V, microwave, and electro-optical probing, plus in-plane horizontal field electromagnetic measurements can be performed on this versatile station. Researchers can use it for testing magneto-transport parameters. The EMPX‑H2 is Lake Shore’s premier probe station for vector-dependent magneto-transport measurements.
-
Product
Active Peak Reading Wattmeter
HF/6
-
Active peak reading wattmeter with simultaneously variable hold time on both the forward and reflected meter movements. This variable delay can be adjusted for quick action for high speed CW, or for longer periods more appropriate for the display of SSB and AM voice peaks. The peak detectors sport a new fast attack design capable of capturing quick pulses such as a single dit. Beautiful industrial design with tri color meter scale and brilliant LED illumination make the DWM series wattmeter a beautiful addition to any station.
-
Product
High Frequency Synthesizer
HFS Series 1.25” x 1” x 0.25”
-
*Surface Mount Package *Broadband Designs Available *Optional Internal Reference *Optional Reference Detect Switch *Internal Reference Output Available *Off-the-Shelf Products Available
-
Product
High Frequency Current Transformer
HFCT Ø 140mm
-
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
Product
High Force Large Area Bond Tester
Sigma HF
-
- For high force and large area- Typically for IGBT, power modules and batteries up to 1000 kgf- High axis speed- Deep access up to 80 mm- SEMI S2 safety cabinet with visual feedback- Flexible positioning of multiple work holders
-
Product
E-DRIV® Brushless Electric Screwdrivers
HF-Series
-
The brushless electric torque screwdriver is built for precision torque control. The electric screwdriver ensures quality and reduces overall assembly failures. These durable power tools feature a Swiss Maxon brushless motor design, which reduces the common maintenance costs associated brush type electric screwdrivers. With almost no expendable parts and simple design, the brushless screwdriver life cycle is extended and maintains a clean working environment. The screwdriver requires less maintenance and part replacement and provides consistently reliable performance. Using a quality brushless electric screwdriver makes a safer world through accuracy and precision.
-
Product
High AC Current Capacitor
LC1/LC2/LC3-RNM
-
Induction Heating Processing Equipment, Electric Current Welding, High Power Resonant Circuits, Motor Controls; Oscillating, Bypass, Coupling circuits, High AC Current applications, High-Frequency AC Filter and Medium Frequency Power applications.
-
Product
Mass Flow Controller for Medium Flow
HFM-205 / HFC-207
-
The HFM-205/HFC-207, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-205 / HFC-207 meters and controllers have flow ranges from 0-1000 slm to flows of 0-2500 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a full complement of fitting and elastomer options, the HFM-205/ HFC-207 covers a wide range of high flow applications.
