Short Testers
Detect unintended circuit connectivity and insulation defects.
-
product
Tester & Programmer
TP-TACT
TP-TACT is designed to test the efficiency and program the operating range of electronic turbocharger controllers.
-
product
Primary Adhesive Tester
DRK129
Shandong Drick Instruments Co., Ltd.
DRK129 Primary Adhesive Tester is applicable in primary adhesive tests of pressure sensitive adhesive tapes, adhesive bandage (plaster), label, protective films and other products.
-
product
Motor Stator Tester
DZ901
Shanghai Aoboor Electric Co., Ltd.
Applicable to precision electrical properties test of stators of y-type three-ohase motors, single-phase motors, hub generators, brushless motors and servo motors.
-
product
Medical Leakage Tester
GLP2-CE
For testing the leakage current of medical equipment to standards EN 60990 + EN 60601.
-
product
Electrical Tester
T+Pro
Safer than solenoid testers and fully compliant with NFPA 70E, (when used properly per Article 110.4 Use of Equipment (A) Test Instruments and Equipment), the T+Pro helps electricians and technicians work safer by indicating the presence of voltage, even when the batteries are dead.
-
product
Continuity Tester
69133
Quickly reveals shorts or broken circuits in all types of electrical devices and controls.Tests for continuity of circuit with power off.Bulb in handle glows when circuit is complete (bulb included).Pointed 3-3/4'' (95 mm) probe gets right to the problem.Deluxe 4'' (102 mm) long handle with removable nylon cap holds replaceable bulb and battery.36'' (914 mm) test lead with alligator clip.Uses one AAA battery (not included).Replacement bulb (Cat. No. 69131)
-
product
Battery Testers
Battery testers are electronic devices designed to test the remaining capacity of a battery's overall charge.
-
product
Multifunction Installation Testers
Shanghai Beha Electronics Co., Ltd.
Loop impedance and prospective short circuit current measurement• Line impedance and prospective short circuit current measurement• Earth loop resistance in TT-systems• Rotary field test• RCD measurements (contact voltage, trip time, trip current - ramp method)• RCD analysis for test of all RCD parameters • Low Ohm and continuity measurement • Insulation measurement up to 1000V (suitable for 690 V industrial mains systems)• Earth resistance measurement with probes and clamp adapters• Voltage and frequency measurement • Current measurement with clamp adapters(optional)• Power and energy measurements• Harmonics measurement for voltage and current upto the 21st harmonics
-
-
product
Insulation Tester
AD-2025
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation ? 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
product
Cone Penetration Tester
DRK8096
Shandong Drick Instruments Co., Ltd.
Determination of compliance with national standards GB / T26991, were compact design, LCD display, automatic data collection and the corresponding statistical calculations, measurement report printout.It can connect the PC output data.The entire testing process is very simple, in full compliance with the provisions of the State Pharmacopoeia. Accurate measurement results, which has good reproducibility, stability of the system.
-
-
product
Voltage Testers
Non-Contact Voltage (NCV) tester quickly checks for the presence of voltage in AC powered systems. It can be safely used up to 1000 V AC. When AC voltage is detected, the testo 745 gives indication by flashing of its RED LED tip and buzzing of its internal audible buzzer. You can easily determine the hot and neutral legs of an outlet without time consuming and risky removal of the outlet from the outlet box.
-
product
Coaxial Short
85140B
The Keysight 85140B coaxial short is used for establishing measurement planes for known reflection phase and magnitude in 50-ohm coaxial systems. It has a 2.4 mm female connector.
-
product
Concrete Tester & Surveyor
CTS-02V4
CTS-02V4 (Concrete Test and Surveyor) is a Non-destructive testing device for estimation of compressive strength of concrete. CTS estimates the compressive strength of concrete based on Mechanical Impedance Method by measuring a waveform of impact force with an accelerometer which mounted on the hammer unit.
-
product
Voltage Tester Pen
TOB-VT
Xiamen Tob New Energy Technology Co., Ltd
Non Contact Voltage Tester Pen For High Voltage Testing. Non-contact AC voltage tester pen has high precision and accuracy, with compact and portable design appearance, and the double plastic shell is to ensure the safety of the users.
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
-
product
Anaerobic Jar Tester
LD-LAJ-A11
Anaerobic JarLD-LAJ-A11with 2.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
-
product
Socket Outlet Tester
Using the new Testavit Schuki 1 LCD and 3 LCD, specialists easily check to see if sockets, cable drums or connecting cables are correctly connected in 230 V installations. Due to three LEDs, the connection status can be quickly and clearly determined. In addition, through the finger contact, it can be tested to see whether an impermissible, high contact voltage is applied at the protective earth connection. In addition, using the Testavit Schuki 1 LCD, a 30 mA FI circuit breaker (RCD) can be triggered via a pushbutton.
-
product
DIP Tester
Model DS-10
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
product
Flame Burning Tester
DRK3024A
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
product
Field Sync Tester
Sentinel
All-in-one TesterPTP, NTP, SyncE and TDMMulti-port, simultaneous measurementsEmbedded GPS Rx and RubidiumHigh performance. Optional battery to maintain Rb in holdover during transit
-
product
Torsion Testers
For maximum torsion testing versatility and capability, Tinius Olsen offers a full range of torsion testing machines in capacities from 1,000 to 30,000 Nm. These uniquely superior torsion testers provide loading and weighing capabilities in both directions of rotation. This feature makes it possible to conveniently determine not only the ultimate torque load of a specimen, but how that specimen behaves under conditions of continuous or intermittent torque loading in both directions.
-
product
Circuit Breaker Tester
GDGK-307
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1) Closing and opening time measurement of 12 channels2) Max difference of closing or opening time measurement of three phases3) C-O and O-C time measurement4) Rated operation sequence test5) Bounce time and frequency measurement of breaker closing6) Circuit breaker closing and opening speed measurement7) Travel-time, coil current-time curve of circuit breaker operation measurement8) Travel and clearance of circuit breaker measurement9) Variable DC circuit breaker operation power supply10) Closing arc resistance value and connected time measurement11) Closing time and opening time of graphite circuit breaker measurement12) Print test results by internal micro printers
-
product
Non-contact Tester
Adjustable sensitivity to detect ACV as low as 5VAC. With sound and light feedback, Battery powered : 4 x 1.5V (L1154 / LR44 / AG13). Worldwide patent pending. Originated, designed and developed by MEET.
-
product
Non-Contact Voltage Tester
NCVT-1
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
product
Equipment Testers
A progressive tester with a wide range of test functionalities. In addition to a device tester, a complete device for the Risk Inventory & Evaluation. (RI & E)
-
product
Portable Hardness Tester
Beijing TIME High Technology Ltd.
A compact, handheld device used for on-site measurement of a material's hardness.
-
product
Voltage Testers
Shenzhen Everbest Machinery Industry Co.,Ltd.
Non-contact detection of 50 to 1000V ACRugged and double molded caseSuitable for outlets or against wire insulation testingFlashing red LED light indicatorBuilt-in bright flashlight with on/off buttonConvenient size with pocket clipAuto power offSystem self testUse on 50/60Hz circuitsComplete with two AA batteriesCATIII 1000VDimensions: 158 x 21mmWeight: 48g
