3U PXI Chassis
See Also: PXI Chassis, 6U PXI Chassis, Portable PXI Chassis
-
Product
3U VPX Processor Card
VPX3-1708
-
Curtiss-Wright Defense Solutions
The VPX3-1708 single board computer delivers the next step in performance while maintaining a similar power envelope to previous NXP processor generations. Available in a safety-certifiable variant, the V3-1708, this commercial off-the-shelf (COTS) processor card is designed to reduce the time, cost, and risk associated with getting rugged, safety-critical systems to the field.
-
Product
PICMG® 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/48
Power Module
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output- Active PFC (Power Factor Correction) meets IEC1000-
-
Product
PXI 2A Multiplexer, 4-Bank, 16-Channel, 2-Pole
40-614C-007
Multiplexer Module
This 4-bank, 16-channel, 2 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PC104p, PCIe104, PCI-104, PC104 Chassis
PC104p-Chassis
-
Suitable for PC104, PC104p, PCI-104, and PCIe104 applications. The chassis is based on an extruded aluminum outer housing with machined end caps. Vibration isolated internal chassis. Water resistant design with gaskets. Available in multiple lengths. Designed in SolidWorks, custom modifications available.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-02
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm SMB
45-720A-751
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
PXI Very High Density Multiplexer, 5-Channel, 32-pole
40-670C-022-5/32
Multiplexer Module
The 40-670C-022-5/32 is a 5-channel, 32-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
SBC347A 3U OpenVPX Intel Rugged Single Board Computer
SBC347A
-
The SBC347A Rugged SBC features the 5th Generation Core i7 processor from Intel, with integrated graphics and memory controller plus quad core processing up to 2.7 GHz.
-
Product
PXI RTD Simulator Module, 4 Channel, PT1000
40-263-503
Simulator
The 40-263-503 is a 4-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI-5670, 2.7 GHz PXI Vector Signal Generator
PXI-5670 / 778768-01
Vector Signal Generator
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
Product
PXI Solid State Switch Module, 6xSPST, 30 A
40-183B-011
Switch Module
The 40-183B-011 has 6 high current SPST switches in two PXI chassis slots. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 30A of continuous current and switch up to 40V signals. The switch can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI 2A Multiplexer, 8-Bank, 4-Channel, 4-Pole
40-614B-005
Multiplexer Module
This 8-bank, 4-channel, 4-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
3U 1-Slot OpenVPX P&G, w/o ROHS, 3.125G
101VPX301P-9005
-
3U 1-Slot OpenVPX Power & Ground, Pass through, RT2-R ruggedized conn, w/o ROHS, Max data rate (Gbps) 3.125.
-
Product
PXI 2 A Relay Module, 26xDPDT
40-139A-202
Relay
The 40-139A-202 (PXI) and 42-139A-202 (PXIe) are 26xDPDT relay modules suitable for high density switching applications with medium power and feature 2 A current capacity with voltage rating to 300 VDC/250 VAC
-
Product
PXI Very High Density Versatile 2 A Multiplexer
40-612B-002
Multiplexer Module
The 40-612B (PXI) and 42-612B (PXIe) Very High Density Versatile Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves.
-
Product
PXI High Density MUX BRIC, 4-Chan, 40-Pole
40-570-211
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI FlexRay Interface Module
FlexRay Interface
PXI FlexRay Interface Modules provide two fully functional FlexRay interfaces, allowing an individual electronic control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. PXI FlexRay Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Single 16x16 1-Pole High-Density PXI Matrix Module
40-520-001
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
3U OpenVPX 9 Slot Variant to Profile BKP3-CEN09-15.2.17X-3
1OVX309KY6-1X11R
-
Hierarchical star, no expansion plane| control plane, 3U, 9 Slots.
-
Product
PXI Signal Generators (Signal Sources)
Vector Signal Generator
Accelerate test throughput with fast, high-quality measurements optimized for RF or microwave design validation & manufacturing testIncrease test configuration flexibility with a PXI platform and license key upgradesReduce development time with easy integration of drivers and programming examples into test environments
-
Product
PXI 3A Power MUX BRIC, 15-Channel, 16-Pole
40-571-205
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
3U VPX RL Thermal Load Simulation Module
-
The 3U power test module is an ideal solution for evaluating heat dissipation in a rugged conduction cooled VPX cage or chassis. This card is a thermal load in the chassis to evaluate the heat dissipation. The chassis can be monitored with temp sensing probes and or FLIR imaging. Different wattages are selected by setting dip switches. The +5 and 3.3V loads are on the top of the module. The +12V and -12V loads are on the bottom side of the module.
-
Product
PXI 2 Amp MUX, Single 32-Channel 2-Pole
40-635-002
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI DeviceNet Interface Module
Interface
PXI DeviceNet Interface Modules have an onboard microprocessor and optically isolated physical layer to communicate with a DeviceNet network system as a master (scanner) or slave device. The modules ship with a high-level API that provides complete access to a DeviceNet network and features easy access to device data and streamlined explicit messaging. PXI DeviceNet Interface Modules are ideal for prototyping DeviceNet systems, PC-based control, embedded control systems, PC-based human machine interface (HMI), and DeviceNet network management utilities.
-
Product
Arbitrary Function Generator PXI Card
GX1200 Series
Waveform Generator
The GX1200 and GX1201 are high performance, single-channel PXI arbitrary waveform generators that combine a function generator, arbitrary waveform synthesizer, programmable sequencer, pulse generator, and modulation generator in one instrument. The GX1200 Series delivers all this at a lower cost than comparable benchtop or VXI-based instruments.
-
Product
PXI Solid State Very High Density Matrix
40-501-001
Matrix Switch Module
The 40-501 is a very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
Product
LS-28-1U Chassis Channel 1 AUX Cable Assembly
28U-CBL-AUX1
-
Cable assembly for LS-28-DRSM 1U Rack Mount Unit
-
Product
PXI 2A Multiplexer, 16-Bank, 4-Channel 2-Pole
40-614A-002
Multiplexer Module
This 16-bank, 4-channel, 2 pole version is part of the 40-614A High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.These 2A multiplexer modules are designed for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI High Density Multiplexer, 5-Bank, 16-Channel, 2-Pole
40-615A-006
Multiplexer Module
The 40-615A-006 is a 5-bank, 16-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI BRIC4 2Resource Distributor, 1Bus Matrix
40-569-021
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
