Filter Results By:
Products
Applications
Manufacturers
-
product
LCR Meters
PeakTech Prüf- und Messtechnik GmbH
A type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component.[1] In the simpler versions of this instrument the impedance was measured internally and converted for display to the corresponding capacitance or inductance value. Readings should be reasonably accurate if the capacitor or inductor device under test does not have a significant resistive component of impedance. More advanced designs measure true inductance or capacitance, as well as the equivalent series resistance of capacitors and the Q factor of inductive components.
-
product
300 V Battery Analyzer
BA6011
The BA6010 Series battery analyzers measure voltage and resistance of modern battery technologies with high accuracy, resolution, and speed. Additionally, these instruments provide auxiliary measurement parameters inductance, capacitance, dissipation factor, impedance, quality factor, reactance, and phase angle in degrees and radians.
-
product
Multi-Operational Surge Tester
MB Model
Bench all-in-one versatile Multi-Operational Surge Tester that you need for all of your electrical insulation testing. The Hi-Pot tester has separate L.E.D. panel meters for direct readout (voltage and leakage current) so that no interpolation on the scopes display is ever needed. This MOST can surge test extremely low inductance windings, DC armatures, etc.
-
product
Programmable Inductance Decade Box
PLS Series
The PLS Series is a broad line of high precision programmable decade inductors. They provide straight inductance in a wide selection of ranges, tolerances andratings. IET Labs also supplies custom combination substituters for capacitance and resistance as well as sources for voltage and current.
-
product
SQUID Series Arrays
The SQUID series arrays are ideal for readout of TES sensors or as amplifier stage for discrete two-stage applications. Integrated bias resistors for TES or two-stage applications reduce wiring complexity. Various arrays with input inductances of 3 to 6 nH, input sensitivities of 17 to 23 µA/Phi0, and a current noise between 5 and 10 pA/sqrt(Hz) @ 4 K are available.
-
product
Automatic Coil Test System
LM Series
Koyo Electronics Industries co., ltd
Models in LM-2100 series equipped with LCR meter are designed to measure inductance and dissipation factor of the coil to which DC current is superimposed. Special circuit is built in to protect the LCR meter from surge voltage. Applied current can be step by step in the remote mode. Voltage application is impossible with the safety cover open.
-
product
High Voltage Economical Resistors
HVE
The HVE series of high voltage economical resistors feature zero inductance, an excellent range of tolerances, wide resistance values and unparalleled high voltage handling.
-
product
Third Harmonic Filter
HBF-T
Lifasa - International Capacitors, SA
HBF-T filters are designed to block the 3rd harmonic, reducing the neutral currents in three-phase installations where there are installed harmonic generating loads connected between phase and neutral. It is basically passive filters based on a parallel combination of inductance and capacitor.
-
product
LC Meter
* Measures capacitance from tenths of a pF to .1 uF * Measures inductance from a few nano-Hy to more than 10 mHy. * Uses small 8 x 2 LCD display * mini banana jacks * 9 volt batter operation * Measures 5.5 x 2.5 x 1.1 inches.
-
product
ST2817B+ LCR Meter (50Hz to 100kHz, 10 points))
ST2817B+ LCR meter is a high-performance and cost-effective measuring instrument. It can automatically measure the inductance L, capacitance C, resistance value R, impedance modulus |Z|, quality factor Q and loss tangent value D and other component parameters. The instrument combines powerful functions, superior performance and simple operation, which can not only meet the needs of high-speed measurement on the production site, but also meet the needs of precision testing in quality inspection, measurement, scientific research and experiment departments.Applications: Passive component / Other component
-
product
Metal Foil Low Resistance Chip Resistor
MFF
*Low Resistance / TCR / EMF / Inductance*Excellent long term stabilityRoHS compliant and halogen free.*Lead free.*High precision current sensing and voltage division.
-
product
PRECISION MAGNETICS ANALYZER
3255B SERIES
The 3255B range of inductance analyzers are able to accurately characterise devices in a clear and simple manner. The inductance analyzers are available in three versions 3255BL (200kHz), 3255B (500kHz) and 3255BQ (1 MHz).
-
product
CT & PT Test Kit
PCT200i
PCT200i is specially designed for current transformer characteristic test.This CT analyzer can finish the measurement class CT and TYP class CT.The additional functions include ratio and angle differential tests (the measurement points in the GB standard),FS and inductance,steady-state parameters,peak error and transient parameters,etc.
-
product
Handheld LCR Meter (100Hz to 100kHz)
ST2822
ST2822 series handheld LCR meter is a portable handheld measuring instrument used to measure the parameters of inductance, capacitance, resistance and other components. Small in size, powered by 8.4V rechargeable battery (ST2822A is 9V non-rechargeable battery) or external power adapter, it can be used not only in desktop applications, but also in mobile measurement and handheld measurement.ST2822 series apply the ultra-low power consumption design and high density SMD assembly techniques and can simultaneously display primary and secondary parameters on a LCD display with backlight. The dual-color shell is gorgeously once shaped; and functions are easy to operate. The test frequency is up to 100 kHz, the readings of primary parameter 40,000 counts and the resolution of dissipation factor 0.0001. Accurate and convenient measurements of passive-components can be achieved in different occasions for a long time.
-
product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
product
Digibridge
1659
The GenRad 1659 Digibridge RLC Tester is an easily programmable, microprocessor-based high performance passive component tester. It automatically identifies the type of component under test and measures in the proper range. The result is simple, precise, unambiguous RLC component testing. The GenRad 1659 RLC Digibridge is an instrument for measuring primary parameters of inductance (L), capacitance (C) and resistance (R) and secondary parameters of dissipation factor (D) and quality factor (Q). GenRad designed this single compact unit with maximum flexibility and operator convenience in mind. The simple front panel design of the Digibridge requires less effort to operate. Digital display and user friendly control allows test parameters and limits to be set easily.
-
product
Precision Current Sensing Resistors
PCR4T
Precision cement resistors designed with four terminals, are distinguished by excellent long term stability & TCR. The Kelvin connections of this device allow high precision measurements even with low resistance values. PCR 4T has a non-inductive copper manganin element inserted into the ceramic case and finally sealed with a ceramic molding. This resistor has low inductance and has high pulse power.
-
product
Test Socket
Contact Pitch Sizes 0.3mm, 0.4mm, 0.5mm, 0.65mm, 0.8mm, 1.0mm (custom pitches available)•Bandwidth < -1 dB through 65GHz•Current Carrying Capabilities 1 - 4 Amps•Pin Contact DC Resistance 10 - 30 mΩ•Environmental -40°C to +150°C•Self Inductance 0.14nH – 0.36nH•Mutual Inductance 0.12nH – 0.32nH•Typical Contact Force 12 – 35 grams/pin•Contact Compliance 75 µm – 200 µm•Custom Cooling Options Available
-
product
Decade Boxes
L C R
PGP Electronics Private Limited
PGP Electronics offers wide range of decade boxes for Inductance, Capacitance and Resistance. These decade boxes offer you a greater flexibility in attaining the required component value and are designed to withstand rugged operation.
-
product
Grypper
Grypper
*Package-size PCB footprint: Since the PCB footprint of Grypper is identical to or smaller than the IC package, only one PCB design is required, enabling a seamless transition from test and validation through production and reducing overall cost of test*No lid required: The package snaps directly without a lid, enabling easy probing, scoping and troubleshooting the topside of the device*Excellent signal performance: A short signal path achieves low inductance and low insertion loss, providing a nearly invisible electrical connection
-
product
Tester Electrical Interfaces
The primary element of the tester electrical interface is the Probe Pin Ring (PPR). Sometimes referred to as a ‘tower,’ this array of spring-loaded probes can be arranged to provide a controlled impedance path, a low leakage connection, a low inductance arrangement for high currents, or just about any connection characteristic you require. inTEST EMS provides electrical interfaces in various OEM-supported designs, inTEST standards, and custom configurations.
-
product
Harmonic Filter Resistors
Post Glover designs, builds and tests their harmonic filter resistors in accordance with applicable IEC and IEEE standards to guarantee their performance. With no two installations ever being the same, our experienced engineers develop the proper solution for your particular application and environment. Our low inductance designs are built using all stainless steel elements in corrosion resistant enclosures chosen for your unique specification. Request a quote for your custom harmonic filter resistor.
-
product
DC BIAS CURRENT UNIT
3265B SERIES
To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.
-
product
Source Measure Units and LCR Meters
Source Measure Units are high-precision, high-accuracy DC instruments that can both source and simultaneously measure voltage and current. Additionally, LCR Meters can measure the inductance, capacitance, and resistance (LCR) of electronic equipment.
-
product
Extreme Temperature Passive Probe
N7007A
Many environmental test engineers today are using standard-temperature probes in extreme temperature condition, which causes physical damage to the probe. Another common practice among environmental test engineers is to simply attach long wires at the end of their probes, which significantly degrades measurement performance due to excessive inductance and reduced bandwidth. Keysight addresses this issue with the N7007A single-end passive probe.
-
product
Precision Metal Clad Shunt Resistor
IRHF
Precision Metal Clad Resistors designed in four- terminal technique, are distinguished by high load capacity as well as excellent accuracy. Isolated voltage and current connections making them suitable for very precise current measurements. Easy current measurement is performed by attaching to current bus directly and connecting to voltage (ampere) metal through flexible wires. The ULH models are UL approved versions. Units have a low inductance, heavy copper terminals. The main application is battery manufacturing test jig.
-
product
QFN Sockets
With the largest QFN catalog in the world, Plastronics has taken a leadership role in designing and developing socket solutions for the newest QFN packages. These sockets offer a modular design in a small outline with very low inductance. The Open Top QFN socket allows for more convenient package loading and unloading in most of the same lead count options as the lidded version.
-
product
Milliohmmeter
AD-710
4 Connectors measurement method, Readable LED indicator 12,7 mm high with brightness control, Autoranging, Slow turning on and off test current (measurement of high inductance elements). Memorisation of 25 results of measurement. Power Supply: High-efficiency acidic ? gel battery
-
product
AC Resonant Test System
Yangzhou Power Electric Co., Ltd
Testing of certain apparatus requires much high voltage or current that a straight AC test system is not sufficient. Thus resonant test reactor with a variable core is needed. The main advantage of such test systems is lower input power and larger output power. The resonant test system is designed to compensate capacitance in the testing circuit precisely by tuning inductance of the test system. AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
product
LCR Meter
LCR meter is used to measure the inductance (L), capacitance (C) and resistance (R) of an electronic component.
