Avionics
all aviation electronics assurance.
See Also: Flight, Aviation, Flight Inspection, AFDX, NAV/COMM
-
Product
Imaging Colorimeters
-
Westboro Photonics offers high resolution, high performance imaging colorimeters to meet the needs of manufacturers for several key applications: Computer and cell phone keyboards: automatic measurement, identification and pass/fail analysis for luminance and chromaticity of backlit glyphs and other lit elements. Beam pattern analysis of the luminous intensity distribution of lamps and LEDs. Avionic light plate panel balancing. Transportation, architectural and municipal lighting and signage.
-
Product
XYZ Bootstrap Directional Gyroscopes
4000H-series
-
Sigma Tek's Directional Gyro with heading synchro output provides a cost effective link to "bootstrap" other instruments requiring heading information for: display orientation to aircraft heading, heading stabilization functions, and other navigational calculations and/or solutions. Specific applications include: Argus Moving Map Display®, L-3 Avionics Stormscope®, and Insight Strike Finder®.
-
Product
PCIe Board
79G5P
-
The 79G5P-TE2C0 is a full-height, half-length, PCIe board fitted & configured with the NAI TE2 function module. The TE2 is a single-channel, tri-redundant, Ethernet communications interface module that supports three traffic classes: Time-Triggered Ethernet SAE AS6802 (TTEthernet™), ARINC 664 Part 7 and Avionics Full-Duplex Switched Ethernet (AFDX®) and IEEE 802.3 protocol.
-
Product
ARINC825 Cards
-
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
Product
Network Interface Controllers for Anonymous Subscriber Messaging (FC-ASM)
Fibre Channel
-
Avionics Interface Technologies
FC-ASM Network Interface Controllers for Avionics applications. The AIT FC-ASM NIC solutions are Quad interface modules providing 4 independent NIC interfaces on a single module. All FC-ASM and Fibre Channel protocol operations are handled onboard, providing an efficient, high bandwidth, FC-ASM protocol offload solution for 1Gbp/s and 2Gbp/s FC-ASM.
-
Product
Avionics Data Bus Tester
CORVUS-300
-
CORVUS-300 is an all-in-one avionics data bus tester combining Bus Monitoring, Time-Domain Reflectometer and Wire Mapping capabilities. Its modularity allows the addition of a Vector Network Analyzer or a Spectrum Analyzer based on testing requirements. CORVUS-300 is stock-listed, NSN 6625-01-703-0413, and managed by AFSC/PZAAC.
-
Product
PXIe Avionics Interface Cards
Interface
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
Product
BusTools Software Analyzer
AFDX-A
-
BusTools/AFDX-A is a Windows 7/10-based GUI application solution from Abaco Systems that establishes new levels of power, flexibility and ease-of-use for AFDX (Avionics Full Duplex Switched Ethernet) traffic monitoring, analysis and simulation. Available for use with our powerful CNIC interface, BusTools/AFDX offers an intuitive interface to view, log, analyze and generate AFDX network traffic at the Adapter, End System, Virtual Link (VL) and Port levels. Contact Goleta factory for listing of supported products.
-
Product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
System
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
Product
MULTI-FUNCTION AVIONICS TEST SET
TR-220
-
Tel-Instrument Electronics Corp.
The TR-220 provides test capability for Traffic and Collision Avoidance Systems (TCAS), Distance Measuring Equipment (DME) and Transponders (Modes A, C, and S). The TR-220 features state-of-the art design technology. Microprocessor control results in easy-to-use operation that requires minimum amounts of training. Setup menu allows storage of various test parameters to facilitate quick recall of test conditions.
-
Product
Interface
RMAC-VME
Interface
Designed for laboratory simulation and production test applications, the Modular Avionics Controller (RMAC) is an intelligent, high performance 6U VME product supporting ARINC protocols and other serial communications. As an evolutionary follow-on product to the successful VME-AIC product line, the RMAC-VME provides a single integrated interface to multiple avionics protocols on VMEbus platforms.
-
Product
ARINC Analyser
-
ARINC429 Data Bus Analyzer is portable equipment used for Avionics technicians and line maintenance personal with convenient, easy to use tools for stepping and troubleshooting ARINC429 Avionics System. This Equipment has dual channels for transmitting, receiving and displays the ARINC429 data.
-
Product
Off-Card Adapter,
3910-FOFE
-
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
Product
8 CHANNELS ARINC 429 Simulator Analyzer Tester
CIC429
-
The CIC429 is a full featured, high performance Serial bus Simulator Analyzer Tester developed by Andor Design for test and simulation of ARINC 429 or similar Avionic buses. The CIC429 is designed as a 5/8 size plug-in card for an ISA bus. An on board microprocessor off loads the host by organizing the data in a predefined structure in the dual port RAM. Programming the CIC429 consists of changing this data, which can be done on the fly for real time applications
-
Product
Avionics
-
Our broad and deep line of avionics interfaces, test platforms, tools and software support the development of modern military and commercial aircraft from small SWaP-constrained platforms to commercial airliners.
-
Product
Avionics Supply Simulation System
-
Spitzenberger & Spies GmbH & Co. KG
Simulation of voltage variations. Simulation of frequency variations. Creation of practical disruptions
-
Product
Becker NAV/RMU/RMI/OBS Test Fixture
TA-3320
-
This NAV test fixture is specific to the requirements for testing Becker Avionics NAV, RMI and RMU products. The panel incorporates specific functionality required for testing these Becker products by the book including special requirements for the RMU 5000 and the IN 3300 series of nav indicators. This BAEE NAV test fixture also facilitates resolver alignment and discrete meter testing through the PG 3300 interface connector. The RM 3300 portion of the panel tests the Becker RMI indicators and allows for sourcing the composite signal from the paired radio or from an external generator. The DME channeling outputs are monitored with discrete LED's as well as the ILS, V/LOC, Glideslope and NAV TEST valids. Discrete test jacks are provided for all the meters and the resolver of the NAV indicator and a dimming source is also provided. When testing the RMU 5000 computer access is through a dedicated connector.
-
Product
High Speed Optical Avionics Network Test Instrument
PXIe-25G
-
Avionics Interface Technologies
PXI Express Instrument for test and simulation of Fibre Channel and Avionics Ethernet (10G and 25G). Instrument provides 4 optical network interfaces and is software configurable to provide 4 ports of Ethernet, 4 ports of Fibre Channel, or 2 ports of each.
-
Product
Avionics Radio and Pulse Tester
T-RX
-
Streamline your avionics radio testing process with the CCX Technologies T-RX Avionics Radio and Pulse Tester. The T-RX is an all-in-one avionics tester that conducts 100+ tests on over 16 systems with only 1 device!
-
Product
PMC Module With 2 Or 4 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation Of Avionic CAN Bus Systems
AMC825-x
PMC Module
ARINC825 (CAN bus) Test & Simulation module for PMC with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AMC825-x PCI Mezzanine Card (PMC) can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
DC-DC Converters
-
TDK-Lambda is a global supplier of DC-DC converters with a broad range of power levels. The commercial off the shelf power solutions encompass industry standard board mounted products to chassis mount configurations for the Industrial, Healthcare, Information and Communications Technology (ICT), and Avionics and Defense markets.
-
Product
Becker Transponder Test Fixture
TA-3400
-
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
Product
Avionics PXI Express (PXIe) Interface Card - Multi-Channel, Multi-Protocol, 1553, ARINC, WMUX Interface for PCIe
Interface Card
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
Product
Avionics Interfaces & Test Instruments
ARINC 664
-
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
Product
Avionics Data Bus Tester
Distributed CORVUS
-
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
Product
Avionics Test & Simulation Interfaces
Interface
Connect your PC laptop, desktop and tablet computers to avionics databuses with pocket-sized Ballard USB interfaces. Ease of use, versatility and comprehensive databus functionality have made these rugged adapters the industry favorite for avionics test, analysis and simulation in the lab and in the field. Avionics labs routinely integrate Ballard interface cards and full-featured network appliances into their test setups for powerful and reliable databus connection.
-
Product
PathWave BenchVue AC Source Avionics Standard Test Software
BV0028B
-
Control your AC source and accelerate pre-compliance testing as per the avionics and military-standard requirements at ease.
-
Product
Data Loading Products
-
TechSAT's data loading products are available to support all standard ARINC data loading protocols: ARINC 615/615A/826/844 for ARINC 429 and Ethernet based data loading. For next generation aircraft, TechSAT's data loading solutions bring portability to data loading over the new generation of avionics bus and network types: AFDX®/ARINC 664, Avionic & Deterministic Ethernet, TTP, and ARINC 825/CAN
-
Product
Simulation And Analysis Software
fcXplorer Analyzer
-
Avionic Interface Fiber Channel Simulation and Analysis Test Software, fcXplorer, is an easy-to-use graphical user interface for Fiber Channel Simulyzer modules. fcXplorer is designed for troubleshooting, optimization, planning and configuration of fiber channel data. The low and high level protocol analysis offers acquisition, filtering, time stamping and interpretation of Fiber Channel data traffic and generates statistics.
-
Product
CPCI Avionics Bus Card
-
Avionics Bus Card is high end ARM core based MILBUS Communication Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have MIL1553B, ARINC429, CCDL, digital I/O interface, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board is based CPCI architecture and can be used with CPCI or PXI backplane. Rear IO Board is used to interface all IO’s of the board from Rear Side.
