-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
8 Port T1/E1/PRI ISDN Simulator
SIM-8PRI
-
The most inexpensive ISDN simulator on the market. This unit has eight PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Sample Conditioning Communications Interface
Pilot Pro Series
-
Parker's Pilot Pro™ package has been designed with a high level of flexibility to accommodate multiple configurations of local area communications networks.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Network Traffic Visibility
-
Organisations and businesses are relying more on the network than ever before. In many instances, the network has become the business, such as is the case for managed service providers (MSPs), residential ISPs, mobile carriers, data centers, etc. Unfortunately, at the same time, networks have never been under this level of threat from malicious sources who want to disrupt or even damage infrastructure with various motivations.
-
Product
PXI Dual SP6T MUX 40GHz 50Ω SMA-2.9
40-784-042
Multiplexer Module
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
cDAQ-9189, 8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785065-01
Chassis
8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9189 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
Product
Entry Level Loss Tester
Model：OLT-20
-
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
Product
WIFI Converter
-
When MRC meter with RS232 interface is connected to RSW-914, the meter can share data via WiFi technology. Therefore, personal devices, like desktop, laptop, smart phone, tablet... with WiFi function can be read the measuring data via WiFi. For example if factory installs Power analyzer DW-6095 along with RSW-914, then operator can monitor the power information (measuring value ) via WiFi network with safety.
-
Product
SIMRC - 8 x Reed Relay Module, SPST
1010-R-8-1-5/1D
Reed Relay
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Active Monitoring or Synthetic Transactions
CloudReady
-
Always-on, end-to-end user experience monitoringNo complex scripting required, Exoprise maintains the actions the sensors takeMonitors app performance via both Web UI and API transactionsFull network path performance information for correlation and outage detection
-
Product
PNA-X Microwave Network Analyzer, 26.5 GHz
N5242B
Network Analyzer
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Interactive Display Networking
-
Wireless interactive display that connects to the network and the display in a presentation or classroom environment
-
Product
40-CH 100G Athermal AWG
-
Athermal AWG(AAWG) have equivalent performance to standard Thermal AWG(TAWG) but require no electrical power for stabilization. They can be used as direct replacements for Thin Film Filters(Filter type DWDM module) for cases where no power is available, also suitable for outdoor applications over -30 to +70 degree in access networks. Flyin’s Athermal AWG(AAWG) provide excellent optical performance, high reliability, ease of fiber handling and power saving solution in a compact package. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications. We can also offer different product packages, inluding special metal box and 19” 1U rackmount.
-
Product
Primary Reference Generator
VCH-001
-
The Primary Reference Generator (PEG) VCH-001 is designed to generate the highest accuracy clock signals in a digital communication network. Main areas of application: – synchronization in telecommunication networks.
-
Product
FieldFox Handheld RF Analyzer, Up To 10 GHz
N9912C
-
Select from cable and antenna analyzer (CAT), Vector Network Analyzer (VNA), and/or Spectrum Analyzer with desired maximum frequency. Capture elusive signals with up to 40 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
NI-9148, 8-Slot, Spartan-3 FPGA, Ethernet CompactRIO Chassis
781502-01
Chassis
8-Slot, Spartan-3 FPGA, Ethernet CompactRIO Chassis - The NI-9148 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using scan-mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. The NI-9148 enables you to add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
Product
cRIO-9048, 1.60 GHz Quad-Core CPU, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
785621-02
Embedded Controller
The cRIO-9047 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for … data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
Datalogger Support Software
-
Datalogger support software packages help enable datalogger programming, communication between dataloggers and PCs, and, to varying capabilities, real-time and historical data monitoring. These software packages provide support for a single station or an entire datalogger network.
-
Product
Fiber-Optic Transmission
-
Fiber optic transmission systems all use data links that work similar to the diagram shown above. Each fiber link consists of a transmitter on one end of a fiber and a receiver on the other end. Most systems operate by transmitting in one direction on one fiber and in the reverse direction on another fiber for full duplex operation. It's possible to transmit both directions on one fiber but it requires couplers to do so and fiber is less expensive than couplers. A FTTH passive optical network (PON) is one of the only systems using bidirectional transmission over a single fiber because its network architecture is based around couplers already.
-
Product
Sofar Data Services
-
Access the largest planetary scale ocean data network from anywhere in the world. Whether you work in research or shipping, aquaculture or advocacy, we have the data to power the ocean understanding and insights you need.
-
Product
Managed Ethernet Switch with L2/L3 Layer Support and Fiber Optic Option
ES2
-
Ethernet Switch module, ES2 provides up to 16 10/100/1000 Base-T 1 Gb ethernet ports. Additionally, there is one 10/100/1000 Base-T maintenance port interface, one RS-232 maintenance/console port interface, and a Fiber-Optic channel with four 10 Gb ports. It also provides numerous L2 and L3 networking, quality of service (QoS) and security features available as described below.
-
Product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
-
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
Product
UV Index Measurement
-
The sglux UV-Index sensors measure the UVI with a worldwide unique low measurement uncertainty of less than 5 %. This makes our sensors compliant to the highest measurement precisions class one according the DIN/EN 5031-11, chapter 8. Since 2018 our product UV-Cosine_UVI (ERYCA) is appointed for public authority tasks: The German Federal Office for Radiation Protection (BfS) services 27 measurement points in Germany for public information of the daily UV-Index. Twenty of these points (Andernach, Chieming, Duderstadt, Fichtelberg, Genthin, Giessen-Wettenberg, Schauenburg-Kassel, Langen, Lueneburg, Munchen-Neuherberg, Norderney, Belm/Osnabrueck, Schauinsland, Tholey, Todendorf, Waldhof-Falkenstein, Waldmuenchen, Wurmberg, Zingst and Zirchow) use the sglux ERYCA to obtain the local UV-Index value. In 2017 ARPANSA (Australian Government’s primary authority on radiation protection and nuclear safety) began replacing the existing biometers with SiC photodiode UV sensors (sglux ERYCA) at all network sites. There are currently thirteen measurement sites in Australia that have been upgraded to the new sensors.
-
Product
PXIe Vector Network Analyzer, 300 kHz to 9 GHz
M9372A
Vector Network Analyzer
Pay for only the frequency range you need with a choice of six frequency ranges up to 26.5 GHz Improve accuracy, yield and margins with the best PXI VNA speed, dynamic range, trace noise and stability Add functionality to your test system with a full 2-port VNA that fits in a single PXI slot Address your multiport applications needs by cascading multiple models Increase throughput and lower costs by adding modules in a multi-site configuration
-
Product
Single Phase Relay Testing
-
Megger’s single phase relay test sets are essential items in the relay engineer’s toolbox. Lightweight, rugged with high compliance voltage and test current. Ideal for testing distribution networks, industrial relays, distance relays in rail power networks and many other applications.
-
Product
RF Amplifier
MLE-02-1G
-
Hangzhou Softel Optic Co., Ltd.
MLE-02 is kind of bidirectional amplifier with one input port and one output port, which forward gain range from 28dB to 41dB and the max gain of reversed path can reach 23dB. It can be used as a trunk amplifier in the traditional coaxial network, also it can be used as an line extender amplifier in the HFC network. Its tank-type construction is convenient for maintenance.
-
Product
Data Acquisition & Analysis
-
Avionics Interface Technologies
We provide fully integrated avionics data bus and high speed network analyzer and data acquisition systems. Combining our extensive product catalog of Avionics interface modules, and our easy to use Analyzer software applications, with our Engineering Expertise, we are able to satisfy a wide range of avionics network data capture and analysis requirements with our COTS products or with customized solutions.
-
Product
DataNet Wireless Data Loggers
-
The DataNet wireless system is a data acquisition solution developed for 24/7 real-time monitoring for mission critical organizations. Boasting a variety of wireless data logger models using ZigBee RF technology, the DataNet solution is capable of measuring parameters such as temperature, relative humidity, voltage, current, or frequency. Choose from DataNet models offering up to 6 inputs or the more cost-effective single or dual input Mini DataNet range, depending on your application requirements. Each DataNet mesh network is managed by a Receiver connected via USB to a Windows-based PC, and also supports addition of wireless Repeater units for extending the network transmission range and improving network robustness.
-
Product
Fiber Testers
-
The PingerPro Series provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
