JTAG Emulators
Exercise a processor's (DUT) on-chip debug services to perform JTAG emulation and debug.
See Also: JTAG, JTAG Controllers, JTAG Debuggers, iJTAG, P1687
-
-
Product
High-Performance JTAG Emulators
XDS560 Series
-
Blackhawk XDS560-class models are offered with PCI, USB, and Ethernet host interfaces. These XDS560 models support the first generation of TI XDS560-class high-speed JTAG connection between Code Composer Studio and the target device.
-
Product
JTAG Emulators
XDS100v2 Series
-
The XDS100-class JTAG Emulator is an ultra-low-cost entry level JTAG debugger for TI devices. Blackhawk offers two models, each with two JTAG target connections. One model includes TI JTAG connections for 14-pin TI and 20-pin cTI JTAG headers. The other model provides ARM 10-pin and 20-pin JTAG connections. Both models are identical in software and device support except for the the target connections, so pick the one that matches your target board connection.
-
Product
Advanced JTAG Emulators
-
Blackhawk offers JTAG Emulators ranging from entry level to full-capability debug probe models supporting System Trace (STM), starting at $99. This includes XDS100v2, XDS200 and XDS560v2-class models that are compatible with Code Composer Studio.
-
Product
JTAG Emulator
Blackhawk USB510L
-
The Blackhawk USB510L JTAG emulator is low cost, and has a USB powered interface.
-
Product
JTAG Emulator
Spectum Digital XDS560v2-STM
-
The Spectrum Digital XDS560v2-STM emulator has System Trace capability, along with a USB powered interface.
-
Product
JTAG Emulator
Blackhawk XDS560v2
-
The Blackhawk XDS560v2 STM emulator has System Trace capability, along with USB powered and LAN interfaces.
-
Product
JTAG Emulator
Spectum Digital XDS510-USBPlus
-
The Spectrum Digital XDS510-USBPlus enhanced JTAG emulator is low cost, along with a USB powered interface.
-
Product
JTAG Emulator for BAE Systems RAD750 Microprocessors
CodeRunner JTAG Emulator
-
Designed for the most hazardous high radiation environments, the BAE Systems RAD750 radiation hardened PowerPC microprocessor is the most advanced processor offered to the space community. From the Mars Reconnaissance Orbiter to the Curiosity Rover, the RAD750 microprocessor has proven time and again to lead the industry in quality, performance, and cost.
-
Product
JTAG Emulator
Spectum Digital XDS510-USB
-
The Spectrum Digital XDS510 JTAG emulator is low cost and has a USB powered interface.
-
Product
JTAG Emulator
Blackhawk USB560v2
-
The Blackhawk USB560v2 STM emulator has System Trace capability, along with a USB powered interface.
-
Product
Regenerative AC Emulator, 600 VAC, 125 A, 90 KVA, 3‑Phase
SL1203A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 45 KW / 66 KVA
SL1214A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Regenerative AC Emulator, 600 VAC, 63 A, 45 KVA, 3‑Phase
SL1202A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Regenerative AC Emulator, 600 VAC, 63 A, 30 KVA, 3‑Phase
SL1201A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Emulators
-
Comware Technical Services, Inc.
Comware’s emulators replace your legacy system with modern hardware without changing the operating system and the application software.
-
Product
Emulator
GCI E84
-
The GCI E84 Emulator is the world's leading tester for development, implementation and qualification of products that must comply with the SEMI E84 Standard. It provides the industry-standard automated test plans that are utilized by virtually every 300mm FAB and equipment manufacturer worldwide. GCI testers are the only solutions that guarantee 300mm factory automation interoperability.
-
Product
JTAG Software
-
Looking for flash programming or JTAG test utilities, we have them. Our software ranges from basic command line utilities to applications that extend the emulator's use in the field or the lab.
-
Product
Emulators
-
High fidelity DC power system and motor drive inverter testing is made achievable with the use of advanced power emulation.
-
Product
JTAG Probe
MAJIC
-
MAJIC (Multi-Architecture JTAG Interface Controllers) JTAG Probes are small, stand-alone, processor-based systems that provide an intelligent connection between host-based development tools (the debugger) and an embedded processor via its standardized JTAG debug logic IP macrocell.
-
Product
In-Circuit Emulator
DS-XA
-
* Emulates XA Derivatives * 2MByte Code and Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 30MHz @ 5V * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software for Windows NT and 95 or Later * 3.3V And 5V Emulation Support * Support for ROMless and ROM Microcontrollers * PLCC Emulation headers
-
Product
Protocol Emulations
-
Message automation and protocol simulation test tool that supports simulation of a variety of protocols (VoIP/IP, TDM, Analog, Wireless) all within a single framework. The application includes various test plans and test cases to support the testing of real-time entities
-
Product
JTAG Isolation Protection
-
Our line of JTAG isolators help protect your investment in computers, development boards, debug probes, and lab equipment. Each model connects easily between your target board and debug probe.
-
Product
high-speed JTAG debugger
Bus Blaster v4
-
Bus Blaster is an experimental, high-speed JTAG debugger for ARM processors, FPGAs, CPLDs, flash, and more. Thanks to a reprogrammable buffer, a simple USB update makes Bus Blaster v2 compatible with many different JTAG debugger types in the most popular open source software.
-
Product
JTAG Debug Probe for Cortex-M
J-Trace PRO
-
SEGGER Microcontroller GmbH & Co. KG
J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission.J-Trace PRO can capture omplete traces over long periods - thereby enabling the recording of infrequent, hard-to-reproduce bugs. This is particularly helpful when the program flow 'runs off the rails' and stops in a fault state. It also supports extended trace features, such as code coverage (so engineers have visibility of which parts of the application code have been executed) and execution profiling (providing visibility as to which instructions have been executed and how often - so hotspots can be addressed and optimization opportunities identified).
-
Product
JTAG USB Controller
NetUSB-1149.1/E
-
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
Product
EPC Emulators
-
The EPC Emulators consist of the MME Emulator, HSS Emulator, SGW Emulator, PDN-GW Emulator, and the PCRF Emulator, which can be used together to simulate the complete LTE Packet Core or individually to create a combination of real and simulated Core Network elements. These Emulators includes all the network interfaces and implements all the communication protocols required for core network equipment to operate in an LTE/SAE network.
-
Product
Battery Emulator And Profiler
E36731A
-
The Keysight E36731A battery emulator and profiler is an integrated electronic load and power supply developed to use with Keysight PathWave BenchVue battery emulation software. An emulated battery gives you a known good reference for testing at any charge level. Quickly assess the effect of design or software changes on battery life by emulating any battery charge state. Leverage emulation and precise current drain analysis to achieve longer battery life or to reduce the size of your device.
-
Product
WAN Simulator / Emulator
LANforge ICE
-
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
Product
MC-MLPPP Analyzer And Emulator
-
The Point-to-point protocol (PPP) is a link layer protocol, which encapsulates other network layer protocols like IP for transmission on synchronous (like T1/E1) and asynchronous communications lines. When transmitted over T1/E1 line, PPP frames are based on HDLC frame structure. Two major features of PPP protocol are:*Authentication*Encapsulation of higher layer protocols
