PCI Carrier
PCI card facilitating the integration of other bus type cards.
-
Product
3 PICMG® CPU, 4 PCI™, 7 ISA Slots Backplane
HPCI-13S4LU
Backplane
- Segment: 1- Slots: 3 PICMG® CPU, 4 PCI™, 7 ISA- Supports AT, ATX power supplies- Dimensions: 314.7 mm x 259 mm
-
Product
XMC-to-PCI Express (PCIe) Adapter
9956
-
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
Product
12 Bit, 2 Channels 3 GS/s PCI Express Gen-3 Digitizer Up To 8 GB Memory
EON Express / CompuScope 123G2
-
The new ultra high-speed, high-resolution Gage digitizers series EON Express CompuScope offers sampling of 3 GS/s at two channels on a single slot PCI Express card and are available with various on-board memory depths from 2 GS to 8 GS
-
Product
PCIe-to-MXM adapter supporting ADLINK Mobile PCI Express Modules with NVIDIA® Quadro® embedded GPUs
EGX-MXM-AD
-
The EGX-MXM-AD is an PCIe adapter supporting ADLINK NVIDIA® Quadro® MXM 3.1 Type A, Type B, and Type B+ GPU modules for quick validation and early development purposes on your AI applications. The following modules are supported: EGX-MXM-P1000, EGX-MXM-P2000, EGX-MXM-T1000, EGX-MXM-RTX3000, and EGX-MXM-RTX5000. A reference thermal solution is available.
-
Product
PCI Very High Density Multiplexer, 49-Channel, 2-Pole
50-670C-021-49/2
Multiplexer Module
The 50-670C-021-49/2 is a 49-channel, 2-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
PCI Express 4 Base Specification Receiver Test Automation
N5991PB4A
-
The N5991PB4A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 4.0 ASICs.
-
Product
PCI-8366, PCI Host, 100 MB/s, Fiber-Optic Cable MXI-Express Device for PXI Remote Control
781400-01
Remote Control Interface
The PCI‑8366 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8366 remote controller provides a PCI link over a fiber-optic cable to the PXI‑8368 remote control module when used for PXI system control. Fiber-optic remote control solutions are ideal for long‑distance‑device control and electrical isolation. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
PCI BUS Interface Card
PCI301
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester PCI BUS Interface Card - The PCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI 16 Isolated Input Digital Interface (10-30V)
8006H
-
Optimized for sensing up to 24V inputs, the 8006H PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs.
-
Product
PCI Programmable Resistors
-
Part of our Sensor Simulation family, these PCI programmable resistor cards are ideal for medical, aerospace and automotive applications.
-
Product
Flexible MiniPCI to PCI Express Adapter
SKU-037-XX
-
The Flexible MiniPCI to PCI Express Bus Adapter (Adapter) was designed to convert a standard MiniPCI bus into a PCI Express bus. It allows you to connect a x1 PCI Express add-in board to a motherboard that has a standard 124-pin MiniPCI connector.The adapter includes a MiniPCI host board, x1 PCIe (x4 PCIe is optional) adapter board and a PCI Express flat cable.
-
Product
PCIe-8432, PCI Express, 2-Port, Isolated, RS232 Serial Interface Device
781744-01
Serial Interface
The PCIe‑8432/2 is a high-performance interface for high-speed, port-to-port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial … interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCI Counter/Timer with Quadrature Board
APC483
-
Several models with a variety of configurations provide up to ten counter/timer channels for counting events, generating waveform control signals, measuring pulse-widths, periodic rates, or quadrature position and monitoring operations.
-
Product
SpaceWire PCI Mk2
123
-
The SpaceWire PCI Mk2 is a 3 SpaceWire port interface device, which can also act as a router, that succeeds the successful SpaceWire PCI-2 card. New features include the introduction of a packet generator in the hardware. This allows the card to generate SpaceWire packets at high speeds without using the host PC’s resources. Similarly, a new packet checker has also been added to the hardware design. The high performance driver boasts a full API which allows the user to control all functions of the card, supporting C and C++. Both the API and board design are common across several other STAR-Dundee devices. This makes it easy and quick to migrate user application software across different platforms. The board also supports field upgrades, such that any future revisions or a requested customisation can be downloaded from the STAR-Dundee website and installed.
-
Product
PCI
-
PCI is a local computer bus for attaching hardware devices in a computer. PCI (Peripheral Component Interconnect) is part of the PCI Local Bus standard. The PCI bus supports the functions found on a processor bus but in a standardized format that is independent of any particular processor’s native bus.
-
Product
PCI High Density Matrix, Dual 20x4 2-Pole
50-511A-022
Matrix Switch Module
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
4, 8, 16, 32 Channel ARINC429 Test And Simulation Module For PCI
APXX429-x
Simulator
ARINC429 Test and Simulation bus interface with 4, 8, 16 or 32 Software programmable Tx/Rx channels plus up to 8 Discrete I/O’s.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm
50-294-013
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
8 SE Or 4 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-8-4
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
PCI, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
783007-01
Interface
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
Product
SIMRC - Carrier Kit
1050-002
-
The SIM Relay Carrier 1050 simplifies the custom integration of small format embedded switching cards. No additional PCB design is necessary. Due to the Eurocard format the carrier can be fitted into a standard case or can be mounted in a 19" rack with side rails. Plug in standard SIM Relay Cards and control your switch application with the provided Soft Front Panel without any additional programming.
-
Product
PCI Express To PCI Express Expansion With 3 PCIe Gen-2 Slots
ExpressBox 2200
-
Precision engineered to Magma’s mission critical standards for performance and reliability, ExpressBox 2200 features three (3) full-length, full-height PCIe slots and flexibility with eight (8) 2.5-inch SATA/SAS HDD or SSD hard drive bays. Designed with your workstation in mind, the EB2200 has a rack-mountable aluminum chassis for integrated removable storage expansion, a 520-watt fanless power supply, auxiliary power, and features Magma’s exclusive quiet cooling control.
-
Product
97 lane, 25 port, PCI Express
PEX 9797
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
Universal Voltage Signaling PCI Card w/ 5 IP Slots
PCI5IP
-
If you want to use IndustryPack¨ modules with your PCI system then the PCI5IP is the choice for you. The PCI5IP combines features you need with simplicity and speed. Up to 5 IP modules can be installed. 32 bit and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection.
-
Product
Low Profile PCI Express 8-Port
7803ec
-
The 7803ec low-profile PCI Express serial interface provides eight RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps. These features make the 7803ec ideal for data-intensive applications that require reliable, fast throughput rates.
-
Product
PCI Precision Resistor Card 4-Channel, 2Ω To 13.6kΩ
50-297-131
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Universal PCI, Eight or Four-port RS-232/422/485 Serial Communication Card
LPCI-COM Series
-
The LPCI-COM Series are eight or four-port asynchronous serial communication cards designed for use in PCI bus computers. The cards support RS-232, RS-422, and/or RS-485 communications which can be selected on a port by port basis.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 470Ω
50-298-114
Programmable Resistor Module
The 50-298-114 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 470Ω with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI 32 Chan I/O, Programmable Threshold
50-412-001
Digital I/O
The 50-412 is a 32-channel Digital I/O card with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel.
