-
product
Bench Power Supplies
Series ABC
Kepco¹s ABC bench power supply embodies the latest features: keyboard data entry, interactive digital display, integral GPIB support, software calibration, high frequency switch mode conversion, wide range input (85-264V a-c) and power factor correction. It meets the EN 61000-3-2 harmonic limits. A built-in EN 55022 Class B input EMI filter is provided. Integral External Trigger and RS 232 ports are now standard features.
-
product
Tone And Probe Kit
3PK-NT023N
For professionals who need fundamental wire identification tools without the extra cost, the 3PK-NT023N basic Tone and Probe Kit is the answer. Use it on de-energized AC wire, telephone/twisted pair wire, all voice and data category rated cable, speaker wire, virtually any cable or wire!
-
product
AC Power Analyzers
Measure voltage, current and power on 4 channels: DC, 1-phase AC or 3-phase ACMake more accurate power measurements: 0.05% at 50/60 HzMeasure current directly: internal shunts to 50 Arms, or with external probes or transducersAddress multiple test scenarios with isolated inputs
-
product
Voltage Testers
DUSPOL
BENNING Elektrotechnik und Elektronik GmbH
phase-sequence test (counter-clockwise / clockwise)single-pole phase test: " symbol (red LED)measuring point illuminationacoustic and optical continuity testfrequency measurement 1 1000 Hzvoltage indication 1 1000 V AC TRUE RMS / 1200 V DCresistance measurement and diode test with conducting-state voltage indicationlc display with background lightingsensor of non-contact cable break detectorload connection via large-scale push buttonsvibrating alert in the test handleshock-resistant housing with protection against dust and water jets (protection class IP 65) and rubberized test handleDIN EN 61243-3 (VDE 0682-401): 2015 standard
-
product
AC Clamp Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
Measures AC voltage and current without contacting condutors.
-
product
Voltage Protection
Are solid state voltage sensing relays with electromechanical output contacts built in a fully draw out case format. Designed for application on AC & DC voltage systems, these relays are ideally suited to monitor power supply voltage levels wherever high accuracy and reliable, maintenance free operation is essential. All power to operate the relays is derived from the sensed input voltage therefore an auxiliary supply is not required.
-
product
EMC Compliance Test Systems
ECTS2
Now in its second generation, the ADAPTIVE POWER EMC Compliance Test Systems use a greatly enhanced harmonics and flicker measurement system and newly designed flicker impedance options to support single and three phase AC harmonics, flicker and AC and DC immunity compliance testing up to the maximum required current of 75A per phase.
-
product
Programmable AC Power Supply
IT7300 Series
In order to meet the bigger range of AC power supply and more complex change characteristics, engineers need more powerful and stable AC power supply to simulate the actual working environment. IT7300 series is the best solution in this area. IT7300 series can be widely applied in the electronics and electrical industry, lighting, aviation, military, specification verification of RD, the use of laboratory testing and factory production online test etc.
-
product
Digital Multimeter
MDM-200 Series
The MDM-200 Series of instruments can measure parameters including AC/DC voltage, DC current, resistance, diodes, carry out on-off tests, zero-line judgement, non-contact voltage detection and the true effective value of AC. It is a tool with excellent performance; the ideal tool for laboratories, factories, radio enthusiasts and when carrying out home improvements.
-
product
Command Encoder/Exciter
Kratos Defense & Security Solutions, Inc.
The Command Encoder/Exciter (CEE) is a rack-mount unit ideal for test and verification of Flight Termination Receivers (FTR) and/or Tone Receiver/Decoders. It accepts a universal AC power input, and it generates a modulated RF output carrier signal adjustable in 100kHz steps from 406MHz – 450MHz from suitable for interrogation all RCC 319 compliant IRIG FTRs.
-
product
Signal Chain µModule Receivers
µModule®
Analog Devices µModule® (micromodule) receivers consist of high performance, high speed ADCs with fixed-gain, high speed amplifiers and antialias filters. Our integrated ADC and driver products include integrated bypass capacitance and simplify the high frequency layout required to preserve ac performance. The board space savings are significant for instrumentation applications such as spectrum analyzers, oscilloscopes ,and communications test equipment, or for communications applications such as high sensitivity receivers, software-defined radio (SDR), or signal intelligence receivers. Our portfolio uses system-in-package (SiP) technology similar to multichip modules (MCM) to integrate components with different technologies, along with passive components to make an integrated subsystem.
-
product
Digital H.V. Insulation Tester(10kV)
6310 IN
Standard Electric Works Co., Ltd
● 2 Lines × 16 Characters LCD● Microprocessor-controlled● Tests insulation resistance up to 20 TΩ● 4 Insulation test voltages: 1000V, 2500V, 5000V, 10000V● AC / DC Voltmeter (30~600V)● Short-circuit current up to 5mA● PI (Polarization Index) indication● DAR (Dielectric Absorption Ratio) indication● Auto-ranging on all insulation ranges● Optical USB to RS-232 data transmission● Well isolated from contact● Well protected from surges● 2 built-in optical LEDs for data transfer● Visual and audio warning of external voltage presence (≥30Vac or ≥30Vdc)● Auto-hold function to freeze reading● Overload protection● Adjustable testing duration: 1~30 minutes● Internal memory for data storage● Displays testing duration for insulation measurement● Auto-off function● 200 measurement results can be saved in memory and recalled on
-
product
Small Form Factor (SFF)
The modular design of the Mini ATR platform allows for various configurations. The chassis can easily be scaled up or down while using the same side walls. DC and AC power variations as well as custom front I/O configurations are available. Elma also offers a wide selection of backplanes in various architectures and has different milled card cage sizes off-the-shelf.
-
product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
6-400V DC / 120-400V AC Universal Voltage Tester
1989A
Peaceful Thriving Enterprise Co Ltd
This is a convenient, low-line voltage tester which features 4 LEDs and 3 neon lamp indicators 6-400VDC or 120-400VAC.
-
product
DC Measurements
Standard Windows sound cards do not respond to DC or frequencies lower than a few Hz. (See Why Sound Cards Block DC Signals below for explanation.)There are two general approaches to get true DC response from a standard sound card: Modify the card, or add an external circuit to convert the DC into an AC signal which can be easily measured by an unmodified card.
-
product
Single Channel Signal Conditioner
SAM-3
Macintyre Electronic Design Associa
The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.
-
product
AC Magnetic Automatic Measurement Equipment
ESS
This automatic measurement equipment to measure magnetic property in commercial frequency is used for quality control and research of materials. It is possible to apply single sheet sample and Epstein sample etc. Sine wave measurement can be made within the range of measurement frequency of 50Hz ~ 400Hz. Measurement of basic magnetic property [B,H,P,S,µ] can be made.
-
product
AC & DC Action Load Test
Shanghai Guantu Technology Co., Ltd.
1. AC action load power supplyVoltage range: 0~1000V;Current range: 5A ~ 100A.2. DC action load power supplyVoltage range: 0~1500V;Current range: 5A ~ 100A.
-
product
Small Engine AC Motoring Dynamometers
SAKOR Technologies developed its new Small Engine AC Motoring Dynamometer specifically to meet the needs of engine manufacturers who must now comply with engine testing procedures required by new emission standards contained in 40 CFR Part 1065. These new requirements apply to almost every kind of small internal engine, including those in handheld power tools and lawn and garden tools.
-
product
AC Test Transformer
Shanghai Guantu Technology Co., Ltd.
How the AC test transformer prevents the overvoltage generated by the frequency conversion series resonance test device is a relatively simple problem, but the overvoltage caused by voltage fluctuation is difficult to appear when the overvoltage protection is set. Generally, the overvoltage of the frequency conversion series resonance test device will appear in the frequency sweep stage of the instrument, that is, in the process of finding the resonance point. Those who have used it know that in the process of finding the resonance point of the frequency conversion series resonance test device, the voltage and frequency have a parabola-like linear relationship. By default, the system finds the high voltage, that is, the apex of the parabola as the resonance point.
-
product
Thin-Type Ionizers
ER-VW Series
Panasonic Industrial Devices Sales Company of America
The Panasonic ER-VW Thin-Type Ionizer uses high frequency AC in an ultra-thin Ionizer for superior static elimination.
-
product
PathWave BenchVue AC Source Control Software
BV0026B
The PathWave BenchVue AC source control software controls and analyses your AC source measurements to understand the impact of events related to power draw.
-
product
Jumbo LCD Digital Multimeter
HH2108
High Accuracy (Basic Accuracy 0.8%). Jumbo LCD display 2000 count, 26mm figure height. Manual Ranging at your choice (30 Range). High Voltage test up to AC 500V and DC 500V. Higher Current test up to 20A AC/DC. Resistance test up to 20MΩ. Erequency test range from 10Hz to 1999Hz
-
product
AC / DC Sensors For High Voltage Measurements
The Mors Smitt CatEnergy sensor range provide a proven, reliable, accurate and cost-effective solution for rolling stock. Based on its capacity of multi-voltage and current measurements, alone Mors Smitt sensor products could be used as single solution for all function requiring high voltage measurement on existing and new build train.
-
product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
product
AC and DC Current or Voltage Transducers
VT7 AND VT8 Series
The Model VT7 Series dc voltage transducer produces an output which is directly proportional to the input from dc to 10kHz. It functions as a millivolt dc shunt or a high voltage isolator to 1000V
-
product
Power Analyzer
2105
The model 2105 provides accurate, reliable, & low-cost power measurement that enables engineering, production test, and quality assurance departments determine precise product power consumption from DC and AC power sources.
-
product
256 Digital Input/Output Channels
CP387
The C387 is a single-width, 6U, CompactPCI module with up to 256 digital input/output channels. The C387 base board supports 128 channels of TTL I/O. Four mezzanine card sites can be populated with other forms of digital I/O including isolated input, isolated output, relay output, AC switch output or differential I/O. The mezzanine card concept allows multiple digital I/O types to be configured within a single module to match the application requirements.
-
product
Resistive & Capacitive AC Load Bank
RCD
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.





























