-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5966-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Universal Programmer
Superpro 6100N
-
The most powerful device programmer in device support you can find in the world, High programming speed, Universal package adaptors thanks for 144pin Universal Pin-drivers, PC hosted and stand-alone dual modes operation, Free software update.
-
Product
PCI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Output, Bank-Isolated Digital I/O Device
778835-01
Digital I/O
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
12-/16-bit 16 Channel DAC for CompactPCI
CPCI395
-
The CPCI395 features 16 analog voltage outputs, integrated on the CompactPCI standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel). Conversion takes place automatically. If desired, channels can be synchronized by presetting the channels and then give a simultaneous update command.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-115
Programmable Resistor Modules
The 40-254-115 (PXI) and 42-254-115 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 920Ω with 4Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Power Supply KORAD 3005D
-
Laboratory power KA3005D is stabilized power supply with programmable memory and continuous control voltage from 0 to 30V and AC smooth regulation range from 0-5A. It has a overvoltage protection and against overload.
-
Product
sbRIO-9205, Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
784787-01
Voltage Input Module
Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The sbRIO‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the sbRIO‑9205 includes up to 60 V of overvoltage protection between input channels and common (COM). In addition, the sbRIO‑9205 also includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection. Non-enclosed modules are designed for OEM applications.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 3U VPX
Model 52690
-
- Accepts RF Signals from 925 to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal levels with up to 60 dB gain- Programmable analog downconverter provides I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Micropositioning Systems
-
Mad City Labs micropositioning stages are designed to complement our high precision nanopositioning systems. Our micropositioning stages provide extended range of motion and are designed to provide a stable platform for our nanopositioners. Our product line includes high precision manual stages and fully automated, programmable stages for use with optical microscopes or stand-alone instruments.
-
Product
DC Power Module, 150V, 2A, 300W
N6777A
Power Module
The Keysight N6777A is a 300 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
50W Power Supply, 8V, 5A or 20V, 2.5A
E3642A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 50W, single output E3642A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
Product
Air Cooled Linear DC Electronic Load
ALx Series
-
The ALx Series utilizes conventional linear MOSFET-based dissipative elements, allowing the series to achieve a very wide voltage-current operating range within the model’s maximum power rating. Using the same heat management innovations developed for Magna-Power’s high density programmable DC power supplies, the ALx Series’ conservative cooling ensures long product life in environments up to 50 °C ambient operating temperature.
-
Product
Electronic Loads
SLM DC
-
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 131k Ohm
40-294-034
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Full Function EtherCAT PCIE MDevice Card
PCIE-1203
-
667MHz dual-core ARM processor2 x EtherCAT ports for high-performance of motion and I/O applicationsSupports common motion SDK for rapid application developmentSupports PTP, linear and circle interpolation, Path table, Compare, Latch, Compare delay DO trigger functionSupports programmable acceleration/deceleration rateDiagnostics for fast error handling can trace command and error message
-
Product
Microprocessor Based Indicator
-
Strong Anodized NEMA4X-IP56 ALUMINUM 1/8 DIN CASE Compact Design Provides Excitation to Transducers or Sensors Accept DC mV/V, V, mA Signal Proportional Analog Output V or mA Easy to Program using 4 ButtonsFront Panel Shunt Calibration User Programmable High & Low Set Point Standard No-Output or Relay Output Optional 8-Step Output, RS232, or BCD Output Available
-
Product
PXI Resistor Module 2-Channel 2R to 131k
40-293-034
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
High Performance Autoranging DC Power Module, 50V, 5A, 50W
N6751A
Power Module
The Keysight N6751A is a 50 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
2-Ch. 6.4 GHz or 4-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - 6U VPX
Model 58141
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Two-channel mode with 6.4 GHz, 12-bit A/D- Four-channel mode with 3.2 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverters)- Four 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Low Power Programmable AC Power Source With Transients
-
Chroma Systems Solutions, Inc.
Equipped with a host of powerful features: power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, waveshape synthesis and regulation test software
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 2Ω to 26.7kΩ
40-252-132
Programmable Resistor Modules
The 40-252-132 is a programmable resistor module with 1 channel which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2Ω to 102kΩ
40-251-134
Programmable Resistor Modules
The 40-251-134 is a programmable resistor module with 2 channels which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Bridging And I/O Expansion Versatility. Rapid Hardware Acceleration For Improved Signal Control.
MachXO2
-
*Up to 256 kbits of user Flash memory and up to 240 kbits sysMEM™ embedded block RAM*Up to 334 hot-socketable IOs that avoid excess leakage*Programmable through JTAG, SPI, I2C or Wishbone*TransFR feature allows in-field design update without interrupting equipment operation*Programmable sysIO™ buffer supports LVCMOS, LVTTL, PCI, LVDS, BLVDS, MLVDS, RSDS, LVPECL, SSTL, HSTL and more
-
Product
PXI-2565, 16-Channel, 7 A, SPST PXI Relay Module
777754-01
Relay
16-Channel, 7 A, SPST PXI Relay Module—The PXI‑2565 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It delivers high-current switching of DC power supplies, AC line power, and AC/DC current sources. The PXI‑2565 is fully software programmable and supports multiple instrument synchronization.
-
Product
5 Channel DAC FMC Module
DACNF05 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF05 is a five channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A. A single-ended external input or output clock is provided. The direction of the clock is programmable from the FPGA of the FMC carrier board.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 2Ω to 26.7kΩ
40-252-032
Programmable Resistor Modules
The 40-252-032 is a programmable resistor module with 2 channels which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Resistor Module 2-Channel 1.5R to 2.04k
40-293-022
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Industrial Battery Manufacturing
-
Analog Devices precision analog front ends and controllers for testing and monitoring battery cells simplify design by providing excellent accuracy, performance over temperature, flexibility with functionality, and overall reliability in a space saving package. Our devices measure battery charge/discharge current through precision fixed gain and programmable gain instrumentation amplifiers, and measure battery voltage via fixed gain and programmable gain difference amplifiers.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-141-HI
-
The 40-230-141-HI (PXI) and 42-230-141-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 201kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-052-HI
-
The 40-230-052-HI (PXI) and 42-230-052-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 5.762MΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
