PXI Digitizers
-
Product
PXI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module
778964-01
Digital I/O Module
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6515 is an industrial digital I/O interface with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI Digital I/O And Prototyping Modules
Prototyping Module
Programmable Input Threshold and High-Side or Low-Side Drive Capability Available on Some ModulesOptically Isolated Input/Output for Interfacing to Electrically Noisy Environments Available on Some ModulesTTL Inputs and Outputs Suitable for Interfacing to External LogicOpen Collector/Drain Transistor Output Versions Suitable for Driving Internal or External Relay Coils
-
Product
PXI-4065, 6½-Digit, ±300 V PXI Digital Multimeter
780011-01
Digital Multimeter
6½-Digit, ±300 V PXI Digital Multimeter—The PXI‑4065 is a 6½‑digit, 300 V DMM, which makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
PXI Digital I/O Module
Digital I/O Module
PXI Digital I/O Modules offer up to 96 channels of digital I/O, with compatibility for a variety of voltage and isolation levels. Some models include programmable input filters to eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter. PXI Digital I/O Modules are ideal for a range of applications, from manufacturing test and industrial control to advanced aerospace and laboratory research.
-
Product
PXIe-5775 , 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Digitizer
785592-01
FlexRio Digitizer
The PXIe-5775 is a PXI FlexRIO Digitizer that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PXIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785162-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Dynamic Digital I/O (3U), 32 Ch., Per Pin Control, Up To 100 MHz W/256MB Memory & LVDS
GX5292
Digital I/O Module
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 32 ch., per Pin Control, up to 100 MHz w/256MB Memory & LVDS
-
Product
PXI-4070, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter
778274-01
Digital Multimeter
6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter - The PXI‑4070 is a high-performance 6½‑digit, 300 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXI‑4070 … delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXI‑4070 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
PXIe-4082, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter
783131-01
Digital Multimeter
PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter—The PXIe‑4082 is a high-performance 6½‑digit, 300 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXIe‑4082 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, frequency, period, and basic L and C measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4082 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5150 Series
Digital I/O Module
The GX5150 Series are high speed, 6U PXI, sequenced digital I/O instruments. The GX5150 master controller has 32 bits of I/O channels that supports test rates of up to 50 MHz and a vector depth of up to 128 Mb per pin. The GX5151 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5150. The GX5150 can control up to 15 GX5151 boards using the same timing and sequencer.
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
PCIe-PXIe-8565
PXI Express Module
Includes PCIe-8560 peripheral card, PXIe-8565 3U system module, and ACL-EXPRESS cable in 1, 3, or 7 meter lengthsCompliant with PXI-5 PXI Express hardware specification Rev.1.0 and PCI Express Base Specifications Rev. 1.0a250 MB/s maximum system throughput
-
Product
Precision Multi-Channel DC Source PXI Card
GX1838 Series
PXI Card
The GX1838 is a multi-channel programmable DC Source providing multiple discrete outputs for avionics automotive, industrial testing and other ATE applications.
-
Product
PCIe-to-MXM adapter supporting ADLINK Mobile PCI Express Modules with NVIDIA® Quadro® embedded GPUs
EGX-MXM-AD
PXI Express Module
The EGX-MXM-AD is an PCIe adapter supporting ADLINK NVIDIA® Quadro® MXM 3.1 Type A, Type B, and Type B+ GPU modules for quick validation and early development purposes on your AI applications. The following modules are supported: EGX-MXM-P1000, EGX-MXM-P2000, EGX-MXM-T1000, EGX-MXM-RTX3000, and EGX-MXM-RTX5000. A reference thermal solution is available.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785164-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
56 Channel TTL I/O FPGA PXI Card
GX3756 Series
FPGA PXI Card
The GX3756 is a user configurable, FPGA-based, 3U PXI card which offers 56, TTL I/O signals. The module consists of a daughter card and the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA.
-
Product
FPGA Mezzanine Card
FMC168
Digitizer
The FMC168 is a digitizer FMC featuring eight ADC channels with 16-bit resolution and 250Msps sampling rate per channel.With a flexible clock generation and distribution scheme, the FMC168 allows control of sampling frequency and analog input gain through serial communication with a carrier card.
-
Product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4I.2211-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
High-Speed A/D 14-Bit Digitizers
Digitizer
GaGe 14-bit resolution digitizer models divide the input voltage range into 16,384 different digitization levels, which improves the delectability limit by a factor of 4 over the 4,096 levels of a 12-bit resolution digitizer model.
-
Product
PCIe 14 Bit High Speed Digitizer - 500 MS/s on 2 Channels
M4I.4450-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PCIe 16 Bit Multipurpose Digitizer - up to 40 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5932-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Ethernet/LXI digitizerNETBOX 16-Bit Multi-purpose Digitizer - 5 MS/s on 4 Channels
DN2.591-04
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.442-16
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5941-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
FPGA PXI Card with 80 TTL Differential Channels Module
GX3609
FPGA PXI Card
The GX3609 is a 3U PXI FPGA card with 80 TTL differential channels. The GX3609 is comprised of a GX3500 FPGA card and the GX3509, 80 channel, differential TTL expansion card.
-
Product
PXI FlexRay Digitizer
PXD7113
Digitizer
The PXD7113 FlexRay Digitizer features a 100MS/s input with 16Bit resolution, input voltages up to ±10V and a bandwidth up to 10MHz. The PXD7113 FleyRay Digitizer has a 2MB memory which allows up to1 million samples. The device has a high common mode rejection ratio (CMRR).
-
Product
PXIe 8 Bit High Speed DIgitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4X.2211-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 125 MS/s on 8 DAQ Channels and 8 AWG Channels
DN2.806-08
Digitizer
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 24 Channels
DN6.592-24
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2233-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 2 DAQ Channels and 2 AWG Channels
DN2.813-02
Digitizer
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
