Burn-In Boards
Printed circuit boards (PCB) filled with integrated circuit (IC) sockets for purposes of connecting an array of IC packages for burn-in test.
See Also: Burn-In, High Power Burn-in, Burn-In Sockets
-
Product
I/O Board
VME-6500 6U
-
The VME-6500 is a 6U VME Multifunction I/O board that can deliver in a single chassis slot the analog and digital I/O capabilities that could previously have occupied four slots, and can therefore make a significant contribution to substantially enhance performance and functional density. A high density and versatile design it provides 8 analog inputs and outputs as well as 16 digital inputs and outputs, all in a single 6U double Euro form factor.
-
Product
VXI Register Interface Board
VXI-5524A
-
*VXI Register Interface mates with user's PCB to form a B or C-size module.* 48 Digital IO Lines - Three 16-bit registers set as latched outputs or gated inputs.* 16 line bi-directional expansion bus for driving external logic.* Digital IO and VXIbus lines are 3.3V logic levels and are 5 V tolerant for compatibility with 3.3V logic and 5V VXIbus signals.* User selectable 3.3 and 5 Vdc puliup voltage on the digital IO lines for sensing switches etc.* The VXI-5524A board is a complete VXI-1 Rev 1.4 and VXI-2 compliant register-based interface.* User configurable model number, manufacturer ID, version and serial numbers.* Two companion component boards available for prototyping IC or RF assemblies.* Companion hardware kits available for building 1, 2 or 3-slot wide modules.
-
Product
Digital Input Board, 32 Isolated Channels, 24V
APCI-1032
-
32 digital inputs, 24 V or 5 V, incl. 16 interruptible inputs Optical isolation 1000 V Input filters Protection against pole reversal
-
Product
3U Hold-Up Board 200W
059-513
-
Hold-Up Board for 28VDC military power supplies which can provide hold up power for up to 200W for 50ms according to MIL-STD 704 / DO160.
-
Product
Compact PCI Connector Board
cPCI-J2-SCSI
-
Ribbon cable is used between the rear IO and SCSI connector. The lengths are reasonably well matched. The cable is short. The design is intended for lower speed IO - 10 MHz and below. Above 10 Mhz there may be some attenuation.
-
Product
8 Relay Output Board
APCI-2200-8
-
*8 relay output channels*Switching voltage 60 V/DC, 48 V/AC, switching current 1 A*Optical isolation*Watchdog*Easy programming
-
Product
Quad IF Board
DP-VME-1242
-
DP-VME-1242 is VME64x, 6U single-slot solution for high sampling rate and down conversion applications. Applications include - IF signal processing, radar systems, communication systems, and GPS systems.
-
Product
Squid Carrier Board™ Family PCI Express Gen 2 Carrier Board for 4 PCIe M.2 SSD Modules
SKU-086-01
-
The Squid PCI Express Carrier board for M.2 SSD modules is the second product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 4 M.2 PCI Express SSD modules. This product is recommended for use in Mac Pro Desktop computers.
-
Product
Connector Board for Cable and Harness Tester
CB49
-
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors.
-
Product
3U Processor Board
CP32107
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® 4th Generation Core™ and Celeron® i7/i5/i3 processors, CP32107 is a high-performance 3U 8HP CPCI PlusIO SBC with up to 4x2.4GHz and 8 threads CPU. For better heat-dissipation, CP32107 is equipped with a noiseless fan that has adjustable rotational speed.CP32107 is provided with rich front and rear I/O interfaces, including 2x USB3.0 for peripheral, 2x GbE (through M12 Connector) for LAN, 1x Display Port supporting 3840x2160 output on front; 2x SATA III, 2x GbE, 4x USB2.0, 2x RS232/422/485 on rear. The rear is compliant with PlusIO Standard, and supports 3 x1 PCIe Gen2.0 interfaces. Besides, mSATA or CFast disk can be installed on CP32107.
-
Product
Single-Function I/O Boards
-
NAI offers, and continues to support, primary or single-function I/O boards designed for a specific, single-purpose application. Based on the specialized application itself, from the interface connectors through the motherboard, to the specific function, these boards typically address I/O function integration challenges requiring higher current capacity, layout, and/or grounding requirements. They are specifically designed for rugged defense, industrial, and commercial applications.
-
Product
SparkFun IR Thermometer Evaluation Board
MLX90614
-
This is an evaluation board for the MLX90614 IR Thermometer. The sensor is connected to an ATmega328 running at 3.3V with a STK500 (Arduino) 8MHz bootloader. Code can be loaded through the FTDI basic interface and the Arduino environment.
-
Product
6U VPX Single Board Computer
VPX6-187
-
Curtiss-Wright Defense Solutions
The VPX6-187 VPX Single Board Computer (SBC) is based on the NXP QorIQ P4040/4080 SOC multi-core processor. Available in versions with 4 or 8 cores running up to 1.5 GHz, and up to 8 GB of high-bandwidth DDR3 SRAM, the VPX6-187 SBC provides high-performance processing and a long list of features and I/O interfaces to satisfy the most demanding requirements of embedded computing.
-
Product
Ethernet, GPIB And USB To Modbus RTU Interface Board
-
ICS's Model 9009 is a multi-interface board that allows Ethernet, GPIB or USB control of Modbus RTU devices. The Ethernet port has VXI-11 protocol for easy control by the following computer systems without special drivers: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. VXI-11 is one of the 9009's Ethernet protocols. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
Product
CPCI-S.0 Standard Compliant Peripheral Carrier Board
MIC-3810
Carrier Board
The carrier board provides a PCIe x16 connector for standard PCIe x8, PCIe x4, PCIe x1 PCIExpress® cards supporting PCIe Gen3 speeds. The carrier board can accommodate cards with maximum dimensions of 176 x 68.9 mm (6.9" x 2.7" inches).
-
Product
Low-cost, Full-Featured Video Frame Grabber Board
Aexeon
-
DescriptionAexeon is a low-cost, full-featured video frame grabber board for analog camera solutions. Aexeon accepts multiple composite, S-Video, or component video inputs in both NTSC and PAL formats and digitizes in both square pixel and CCIR-601 resolutions. With on-board processing, complete camera control, and video output, Aexeon is the perfect product for analog camera OEM solutions.
-
Product
PCI Express A/D Board
AD14-500 Series - Dual 14 bit, 500 MS/s
-
The AD14-500 series has two 20-500 MS/sec 14-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at up to 4GB/sec (500MS/s * 2 bits per sample * 2 channels). Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
Product
3U VPX Single Board Computer
VP32002
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP32002 is a high-performance 3U VPX single-board computer, compatible with PC architecture, especially it is a China Local-design, Local-assembling product. VP32002 is an all-in-one design, supporting the 3rd generation of Intel core processors and QM77 chipset; also supports up to 16 GB onboard DDR3 memory and up to 32GB Disk-On-Modules, these features ensure its stable operation in strong shock and vibration environments. VP32002 supports a XMC interface and various I/O interface such as two SATA600 channels, two Base-BX/T GbE, two UARTs and two USB interface.The board provides a flexible PCI-Express bus interface to the backplane. The interface can be configured as follows: 1 Port x8 PCIe, 2 Ports x4 PCIe, 4 Ports x2 PCIe. This feature makes it suitable for either distributed switching system or centralized switching system.For the user to quickly form application solutions, LinkedHope provide VP32002 a complete driver package including Windows, VxWorks, Linux and QNX.
-
Product
High Speed Communication Board
MS 1712
-
- 12 Channel RS422 Standard Communication interface- 4 Channel Configurable Manchester Bi-Phase Signal communications- 4MBPS configurable baud rate- VIRTEX4 FPGA based design- Hardware Frame formation- Hardware Data validation with START & END frame identification and Checksum calculation for RS422 communication- 1MB DPRAM for PCI interface- Separate set of FIFO's for Transmit and Receive channel- 16 Channels data recording through CF (Compact Flash Storage - Capacity up to 8Gbyte) up to 30min @ 2Mb/sec- Online download through USB interface- Driver interface for Windows2000/XP/VISTA and LINUX OS- 6U size cPCI Board- Hot Swap facility is provided for the live Insertion and removing of the board- 12 RS422 channels in front panel interface using two 25-pin D-Type connector
-
Product
PCI Data Acquisition Boards
AD12-100DMA Series - Dual 12-bit A/D, 25 MS/s
-
Model AD12-100DMA is similar to the ADDA12-100DMA, but does not have D/A converters.
-
Product
6U CPCI D/S, S/D, I/O & Comm Board
78CS2
Multifunction I/O
NAI’s 78CS2 is a 6U cPCI Multifunction I/O and Communication Board designed for applications requiring Digital-to-Synchro/Resolver (D/S) stimulus output, as well as I/O and communication functions. This board contains five independent function module slots. The board can be configured for 10 D/S channels, or for D/S in combination with I/O and communication modules. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
I/O Expansion Boards
UIO40-Express Series
-
Extra I/O expansion selection for the different applications to support diverse UIO40-Express 2.5” core boards.
-
Product
Hall Sensor Board with I2C Interface
055-013
-
Version: +5V/5A +3,3V/5A +12V/5A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
VP F6x/msd, 6U VME processor board
VP F6x/msd
-
VP F6x/msd is a 6U VME processor board designed to extend the life for VMEbus deployments by using the tried and tested Universe-II VME bridge. It is based on a 4-core Intel® Xeon® E3-1505L v6 processor.
-
Product
PXI I/O Board
MZ-TrigIO
Digital I/O Module
The MZ Trigger I/O Board (MZTIO) is a break-out board for the Pixie-16 PXI chassis backplane providing real-time access to Pixie-16 logic signals.
-
Product
Hall Sensor Board with I2C Interface
056-742
-
Version: +5V/60A +3,3V/60A +12V/90A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Clockand Trigger Synchronization Board
CLKSYNC-PCI
-
CLKSYNC-PCI is a clock and trigger distribution board designed to provide up to eight synchronous clock and trigger outputs. The CLKSYNC-PCI is designed for use with multi-channel, ADC and DAC systems where clock and trigger synchronization are required.
-
Product
Load Boards
-
The Hartmann Load Boards were originally designed for in house use to test, setup and qualify standard chassis and custom systems. As demand for these products presented itself, Hartmann answered the call with a lineup of high quality load boards.
-
Product
Sensor Board for micro:bit
-
The MonkMakes Sensor Board for micro:bit allows you to sense sound level, temperature and light level. You can connect it up to your micro:bit using alligator clips.
-
Product
2-Axis High-Resolution Laser Axis Board for VME
10898D
Laser Board
The 10898D 2-axis high-resolution laser axis board provides the same resolution as the Keysight 10897D high-resolution laser axis board with increased slew rates and reduced noise. The increased stage velocity limits and low noise compared to previous laser systems offer premium positioning repeatability and accuracy for advanced applications such as IC fabrication equipment.
