Multifunction I/O
See Also: Mass Interconnect
-
Product
Ethernet I/O Modules
ADAM-6000
-
Advantech's Ethernet I/O Modules, ADAM-6000 series, accomplishes this integration easily through the latest internet technology, so that it can remotely monitor the device status more flexibly. ADAM-6000 modules are empowered by Peer-to-Peer (P2P) and Graphic Condition Logic (GCL), and can perform as standalone products for measurement, control and automation with Advantech's P2P and GCL technology.
-
Product
6-24V Multi-functional Auto Tester With LED Display
6510
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
Product
Dual Channel Multi-function Decommutator
LS-55-DD
-
The Lumistar LS-55-DD PCI Dual Multi-function PCM Decommutator offers two multifunction decoms and two optional bit synchronizers (LS-45) in a single PCI card slot. The multi-function decoms are implemented in FPGA using a next generation design based on the LS-50-P. The simulators,decommutators, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through a low-profile daughterboard. CVSD voice, h.261 video, and IRIG Chapter 8 decoding are achieved through software.
-
Product
8AI Modbus RS-485 Remote I/O
ADAM-4017+
-
8ch analog input(current or voltage)Protocols:Modbus RTU,ASCIIWatchdog timer to recover the system3000VDC isolation protection
-
Product
Multifunctional Meter
CPM-20
-
CPM-20 multifunction power meter provide high accuracy single phase and three-phase measuring and displaying, energy accumulating, power quality analysis, and data communication.It provides maximum/minimum records for power usage and power demand parameters.Hardware standard built in a RS485 Modbus communication port.FCC and CE Approved
-
Product
6RTD Modbus RS-485 Remote I/O
ADAM-4015
-
6ch RTDProtocols:Modbus RTU,ASCIIWatch dog to recover the system3000VDC isolation protectionWiring burned-out detection function
-
Product
PCI Digital I/O Boards
PISO-P8SSR8AC
-
The PISO-P8R8 is an 8-channel isolated input/output interface board for the PCI-Bus computers.The PISO-P8R8 provides 8 electromechanical relay outputs and 8 optically isolated inputs, while PISO-P8SSR8AC and PISO-P8SSR8DC can be used in various applications including contact closure, external-voltage sensing,external-switch sensing and loading switching and designed for one 37-pin D-Sub connector.It can be installed in a 5V PCI slot and can support true "Plug & Play"
-
Product
Temperature Input Module For Remote I/O
Module
The Temperature Input Module for Remote I/O features a features a thermocouple input range of ±100 mV and a voltage input range of ±5 V. It also has an adjustable filter time for improved measurement quality and optional external CJC or PT100 RTD measurements.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Temperature Input Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
Product
JTAG/Boundary-scan Digital I/O Module
ScanIO-300LV
-
The ScanIO-300LV JTAG/boundary-scan digital I/O module turns an IEEE-1149.1 boundary-scan controller (such as the Corelis PCI-1149.1/Turbo or NetUSB-1149.1) into a powerful digital interconnect and functional tester.
-
Product
PCI Express Digital I/O Boards
PEX-P8POR8i
-
PCI Express x1, 8-channel isolated digital input.8-channel PhotoMos Relay output. Includes one CA-4002 D-Sub connector.
-
Product
Digital I/O Modules
-
ADAM-5000 DI/O modules are equipped with high density channels, isolation, short circuit protection, failure protection and hot swap functionality.
-
Product
Multifunction Tester
EASYTEST
-
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
PCI Express Analog and Digital I/O
826
-
Six advanced 32-bit countersDirectly supports incremental encoders, pwm/pulse generation, frequency/pulse/period measurement16 analog inputs, 16-bit, 300 ks/s8 analog outputs, 16-bit, 900 ks/s48 digital I/Os with edge captureWatchdog timer, 3 stages
-
Product
USB Controlled Multi-Function DAQ For ATE Education And ATEasy Training
GT98901 Series
-
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users with a simple yet complete vehicle that replicates many of the stimulus and measurement functions associated with ATE systems. When combined with Marvin Test Solutions' ATEasy® Test Executive and Test Development environment, the GT98901 is the ideal product for creating and supporting ATE training and education applications.
-
Product
32-CH Separate I/O Terminal Base
HSL-TB32-MD
-
The HSL-TB32-MD discrete I/O terminal bases provide reliable and convenient wiring for HSL-M series products. The separate connection can make it easy to wiring, and the separate fuse can protect each I/O point. This low cost terminal base is particularly useful for users who need convenient way to construct their own signal ?Vcondition arrangement.
-
Product
8DI/8DO RS-485 Remote I/O
ADAM-4050
-
8ch digital input/8ch digital outputProtocols: Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
PCI-6511, 64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated Digital I/O Device
778966-01
Digital I/O
The PCI-6511 is an industrial digital input interface, with eight banks of isolated channels. If a computer or application fault occurs, the PCI-6511 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Safety Certified I/O Modules
HY-TTC 30XSH
-
HY-TTC 30XSH, a member of the HY-TTC 30X family, is certified by TÜV Nord according to the EN 13849 standard and fulfills Performance Level c (PL c) requirements. Just as the other family members this certified unit must be used in combination with a master module. For safe communication the standardized CANopen Safety protocol is applicable since compliance to the European standard EN 50325-5 for CANopen Safety is provided.
-
Product
Analog I/O and Digital Receivers
-
Curtiss-Wright Defense Solutions
Many mission-critical applications require small form factor solutions, but cannot compromise ruggedization requirements or I/O and processing performance. Our VPX, XMC, PMC and FMC module-based sensor I/O solutions are designed to handle the toughest operating environments while packing maximum functionality in a minimal physical footprint.
-
Product
8AI/5DI/4DO Intelligent I/O Gateway
ADAM-6717
-
Linux Open Platform8ch analog input (current or voltage)/5ch digital input/4ch digital outputProgram by linux C API, Node-RED (graphic programming environment)Cloud/Database access, edge data analysis and logic control, data visualization by dashboardInterfaces: x2 RS-485, x2 Ethernet port, x1 USB Type-A 2.0, x1 USB Micro-B 2.0
-
Product
Mixed Signal, Multi-Functional Test Module
PXIe-ScanIO-112
Test Module
The PXIe-ScanIO-112 delivers a powerful combination of digital, analog, and AC-coupled testing in a single PXIe module. With 104 boundary-scan controllable digital I/O channels and 8 analog I/O channels ranging from –15V to +15V, engineers gain the flexibility to test a wide variety of board-level designs. The module supports IEEE-1149.6 AC-coupled interconnect testing, configurable single-ended and differential pin operation, and integrates seamlessly with the Corelis ScanExpress™ suite.
-
Product
Multi-Functional Dynamic System Monitor
PFMonitor
-
The PowerFactory Monitor (PFM) is multi-functional Dynamic System Monitor which fully integrates with DIgSILENT PowerFactory software. The PFM features grid and plant monitoring, fault recording, grid characteristics analysis by offering easy access to recorded data, analysis of trends, verification of system upset responses and test results.
-
Product
High Speed Digital I/O
-
ADLINK's high-speed digital I/O cards features 32 or 64 high-speed single-ended I/O channels and up to 50 MHz data transfer rate with 200 MB/s data throughput—ideal for large-scale digital data exchange.
-
Product
Multifunctional Thermal Imaging Monocular
FLIR Breach® PTQ136
-
Built for the rigors of law enforcement, the FLIR Breach PTQ136 spots the heat of suspects and objects in total darkness. Featuring the new FLIR Boson core and a compact design, the FLIR Breach offers unmatched tactical awareness. Weighing only 7.4 ounces (210 grams), the FLIR Breach can be concealed in a pocket or mounted to a helmet with its mini-rail feature, while adding minimal weight to officers’ heavy gear. Additional features include onboard recording and seven palettes for fast detection of suspects or evidence, day or night.
-
Product
8AI RS-485 Remote I/O
ADAM-4017
-
8ch analog input(voltage or current)Protocols:ASCIIWatchdog timer to recover the system
-
Product
Communication and Differential IO Board
MS 1707
-
- Four RS232 PORTS with full handshake- 16 Differential Input Channels- 16 Differential Output Channels- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Mobile Apps for iOS and Android
LoggerLink
-
LoggerLink Mobile Apps are simple yet powerful tools that allow an iOS or Android device to communicate with our CR200X, CR800, CR850, CR1000, CR3000, or CR6 dataloggers via an IP device (NL115, NL116, NL120, NL121, NL201, NL240, RavenXTV, RavenXTG, LS300G). LoggerLink for Android also supports Bluetooth communication for these same dataloggers using an RS-232-Bluetooth adapter. The apps support field maintenance tasks such as viewing and collecting data, setting the clock, and downloading programs.
-
Product
Multifunction Instrument for Education and Training
LabXplorer
-
LabXplorer turns your desktop, laptop, tablet or smart phone into a powerful, multifunction test and measurement instrument for a wide range of applications. Instruments, whatever you need, are at your fingertips. LabXplorer provides multimeter, oscilloscope, spectrum analyzer, logic analyzer, programmable analog and digital signal generator, impedance analyzer and also measures characteristics of passive electronic components and semiconductor devices.
-
Product
4DI/4Relay Modbus Ethernet I/O
WISE-4060LAN
-
Supported protocols: Modbus/TCP, TCP/IP, UDP, DHCP, HTTP, MQTTSupports RESTful web API in JSON formatSupports local logging with RTC time stampSupports mobile device web configuration in HTML5Supports 10~30 VDC power with reverse protection
-
Product
I/O Rack
-
ADAM-5000/485 and ADAM-5000E are Modular I/O System, as well as 4-slot / 8-slot Distributed DA&C centralized i/o systems which conform to the EIA RS-485 communication standard. RS-485 was specifically developed for industrial applications to transmit and receive data at high rates over long distances. The ADAM-5000L/TCP and ADAM-5000/TPC are both Ethernet-based I/O systems. Without a repeater, they can cover a communication distance up to 100M.
