RF Switching
The opening and closing of RF connections.
-
product
Reference Detect Switch
RDS Series 1.5” x 1.5” x 0.6”
*Connectorized Package *Internal/External Reference Detect Switch *Standard Internal TCXO (±2.5 ppm) *Optional Internal OCXO (±90 ppb)
-
product
Switch Probes
A switch probe is designed primarily for “presence/ electrical” test applications such as detecting the absence or presence of contacts within a wire harness connector. In this case, the switch probe provides electrical interconnection and verifies the connector has been manufactured properly. If contacts are missing or out of place, the part is rejected. If all the contacts are in place, the part is accepted and an electrical test is performed, verifying the electrical integrity of the connector and the wires within the harness.
-
product
Diaphragm Operated Pressure Switch
1000W
Extremely rugged construction provides excellent reliability in chemical, petroleum and industrial plants. Bellville spring movement permits mounting of control in any position and helps prevent contact chatter. new design also provides high overpressure protection. Available with standard weatherproof housing to meet NEMA-1 through 4X and NEMA-13, JIC.
-
product
Latching Waveguide Switches
Waveguide switches enable switching between two RF channels. The latching type is stable in both positions without holding current. Manual and automatic (electromagnetic) actuators are available.
-
product
Vibrating Level Switch
TF 100 Series
TF-100 Series is a vibrating level switch with TF-L relay output and TF-P transistor output or with TF-T current output.This level switch is designed for reliable indication of clean liquids and light slurries. It is available with Relay, Current, and PNP outputs that can be set to indicate alarm on either high level for spill prevention, or low level for run-dry protection.
-
product
RF Milliwatt Meters
Type NDB-2 and NDB-3
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
product
Portable Monitoring Receiver and RF Recorder
IZT R3301
The IZT R3301 is a portable receiver with an integrated server for data recording. The receiver is optimized for recoding of RF signals in frequently changing environments. The RF characteristics of the IZT R3301 are identical to the IZT R3000 series. # HF-VUHF-SHF receiver# frequency 9kHz...3GHz (3...12GHz option)# continuous spectrum recording of 24 MHz bandwidth, IQ recording with 20 MHz
-
product
RF And Microwave Accessory Kit
N9311X
N9311X RF and Microwave Accessory Kit complements Keysight's low-cost handheld and benchtop solutions. These accessories provide you with a complete solution when using Keysight handheld and low-cost benchtop solutions for your measurement needs.
-
-
product
Meter Test Switches
TESCO introduced the original Meter Test Switch in the early 1920’s. Today, TESCO’s line of Test Switches has been redesigned with the intention to combine the best features of tried and proven switching methods with improvements in materials and construction. All of the current carrying parts are bright tin plated to prevent corrosion. Good operating contact is assured on periodic meter tests, even when the switch has been idle for long periods of time in an unfavorable atmosphere.
-
product
IPD RF Components – LTCC
Pulse’s complete offering of LTCC based Band Pass Filters, Balun’s, Diplexer’s and Couplers used in conjunction with our wireless antenna products will enhance your devices performance keeping attenuation and noise to a minimum. Many of Pulse’s IPD components are already qualified or referenced on various radio designs, so please contact us about the components already qualified on the radio you are using. From Wifi Networking devices, to smart phones and tablets, Pulse’s offering of IPD Components has you completely covered. Using the table below you can search our complete IPD Component offering.
-
product
RF Signal Generators
The G6 VSG from Transcom Instruments is a Vector Signal Generator that operates from 10 MHz to 6 GHz. It can simulate GSM, EDGE, CDMA, TD-SCDMA, WCDMA, CDMA2000, TD-LTE, FDD-LTE, NB-IoT, and LoRa base station signals for production and calibration of UE, chips. The signal generator has a dynamic range (power range) from -100 to 10 dBm and an in-built automatic gain control function. It is available in a module that measures 180 x 50 x 290 mm and is ideal for educational practices, wireless monitoring, mobile communication, aerospace and national defense industry in terms of research, manufacturing, testing and measurement, and electronic countermeasure.
-
product
RF Spectrum Power Meter
SPM-50
SPM-50A Spectrum Power Meter brings innovative testing concept and approach for RF cable system installation and maintenance. It combines the key function of spectrum analyzer and power meter, designed to measure the power characteristics of particular signal among mixed signals transmitted on cable, fast and accurately present result in power histogram or spectrum chart.
-
product
7-Pole Test Switch Protectors
6442 & 6442-C
With safety always being a concern while working with electrical boxes, you can depend on TESCO’s Test Switch Protectors (Catalog No. 6442 & 6442-C) to alleviate any uncertainty. This was developed to provide temporary protection of the test switch and to address the rising concern that the terminals of the test switch are exposed while you’re working in the box. The switch protector can prevent incidental contact with live terminals or contact with tools. TESCO’s Test Switch Protectors are constructed of clear, flexible PVC with a voltage rating of 2500V. The switch protector will fit any brand of test switch, regardless of manufacturer, from 4 to 7-pole. TESCO can also develop custom designs of this product to meet unusual test switch configurations.
-
product
Rotary Limit Switch
AMETEK Sensors, Test & Calibration
When motion is expressed in shaft rotation, we can provide limits that are adjustable throughout the entire range of movement. Rotary limit switches can be used for material handling on crane or winch drums, hoists, lifts, screw jacks, or platforms.
-
product
RealProbe RF Probes
Unmatched performance In-Circuit RF Probes covering up to 18GHz. These are must tools for any in-circuit RF and Microwave testing and troubleshooting.
-
product
RF Test and Measurement Solutions
Signal GeneratorsSwitch MatricesProgrammable AttenuatorsControl ProductsSignal MeasurementModular Test SystemsCustom Test SystemsUser-Friendly Control Software
-
product
Low Flow Protection Switch
Truflo
Parker Bestobell’s Truflo is an effective low flow protection switch that provides protection against flow changes that could be detrimental to equipment and processes. It provides a warning to operators of insufficient or excessive flow.
-
product
Unmanaged Ethernet Switches
CommFront offers a range of rugged, industrial-grade, managed and unmanaged Ethernet Switches. These Industrial Ethernet Switches have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of 10/100/1000M for both Fast and Gigabit Ethernet networks. In addition, our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet Switches support both point-to-point and multi-drop (daisy-chain or self-healing redundant ring) fiber optic networks, which are designed to cover large areas. These industrial Ethernet Switches support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. When configured as a ring network (managed Ethernet Switches), the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same ring, making the entire Ethernet network more robust and reliable.
-
product
Dual Passive Switches
MAX4888C
Supports Multiple High-Speed Interfaces up to 8.0Gbps While Maintaining Signal Integrity in the Application
-
product
RF Signal Source
DSG800A
The DSG800A delivers outstanding performance in the same class of economical RF signal sources with full frequency and power scanning capabilities, as well as AM/FM/ØM analog modulation, powerful pulse modulation and newly added IQ modulation. Compared to similar products, the DSG800A has the smallest footprint, light weight and superior portability, making it an excellent choice for educational laboratories, industrial production lines, development and research applications.
-
product
Rack Type Optical Switch
JW8402
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW8402 rack type switch is mainly used in optical switching devices and systems to achieve routing, wavelength selection and self-healing protection functions.It can be configured as 1 * 2 / 1 * 4/ 1 * 8 channels and other customized channels according to customer requirements.
-
product
RF over Fiber Link TX/RX
L-Band
QuestTel''s Satellite L-Band optical fiber Transmitter/Receiver set offers high pefromance and cost effective alternative to conventional coaxial systems. The L-Band Transmitter and Receiver pair is used for transporting L-Band RF over fiber from the antenna to the satellite receiver. Additionally transmitter provides optional 13/18V LNB power as well as Automatic Gain Control (AGC) to manage RF input level. By transporting the L-Band RF over fiber this range can be extended from several hundred feet to over 80 miles. Since optical signal is not affected by electromagnetic field, the quality of your signal will always stay at the high level. Also this fiber solution is more cost effective than coaxial system, as well as more reliable and flexible.
-
product
DUAL RF Multiple-Input/Output
FMC-SDR400
Sundance Multiprocessor Technology Ltd.
FMC-SDR400 is a Dual RF multiple input/output module (MIMO) based on AD9361, 70MHz – 6GHz RF transceiver and AD9656 ADC for baseband sampling of less than 70MHz (input only in this range). A software selectable gain and tunable RF bandpass front-end section provides high RF sensitivity by allowing rejection of out-of-band-of-interest interfering signals.
-
product
EMCTD Broadband RF Safety Systems
The EMCTD analog Smart Fieldmeter® is easy to read and to operate. The EMCTD broadband electromagnetic probe covers the 0.2 to 3000 MHz spectrum where most common industrial, communications, medical and government RF emitters are found. The ANGPE-3000 system enables checking of home, office, and workplace RF levels. The system is designed to conveniently measure RF levels around WiFi access points, RFID systems and rooftop antennas; to find transmitter cabinet radiation, locate transmission line leaks, to identify non-radiating antenna elements, and much more. With the supplied NIST-traceable calibration, this system supports laboratory testing of RF devices in compliance with present EMC and RF safety standards.
-
-
-
product
RF R-PHY Video Engines
ATX’s RF R-PHY video engines provide a mux pass-through function that enables cable operators to maintain existing video encryption functionality on in-service edge QAMs, alleviating the need to migrate encryption functionality to the CCAP video core during early stages of DAA transition. ATX RF R-PHY video engines also relieve MSOs of undertaking back-office system integration to reconfigure and manage muxes and broadcast lineups in CCAP video cores. For MSOs considering an accelerated transition to IPTV, the ATX RF R-PHY Video Engine provides a low-cost and low-complexity alternative to implementing a CCAP video core.
-
product
AC Control Time Switch
IM1756
Ajinkya Electronic Systems offers AC and water cooler controller, an energy saving device for controller air conditioner unit and water cooler optimally to save Electricity. AC Control Time Switch offers unparallel features to not only save energy but to save compressor from electrical voltage and overload.
-
product
Switch Filter Bank
Corech Microwave’s Switch Filter Bank frequency covers DC to 50GHz, featured with multi-channels (4 to 8 channels), high power handling, and fast switching options. Pin Diode Based Switched Filter Banks provide the highest level of signal isolation, higher operating power levels, and lower insertion loss and achieve switching speeds of < 40 nanoseconds.
