Bare board Fixtures
accurately position and retain unloaded PCBs.
See Also: Bare Board Testers, Board Test Fixtures, Bare Board
-
product
Single Board Computer
VME-184
Curtiss-Wright Defense Solutions
The SVME/DMV-184 combines the performance and I/O capabilities of the MPC8640 processor with an extensive I/O complement, resulting in a highly capable processing platform for a wide range of embedded military and aerospace applications.
-
product
PCIe Board
Solar Express 200 (SE200)
Sundance Multiprocessor Technology Ltd.
Solar Express 200 (SE200) is x8 Gen3 PCIe carrier board with two SoM-PF m(System on Module) sites. The 2 SoMs that can be supported on this carrier are SoM-PF1 and PF2 which are based on MPF500-1FCG1152 and MPF300T-1FCG784E respectively.
-
product
PCI/PCIe I/O & Comm Board
76C2
NAI’s 76C2 is a PCI/PCIe multifunction I/O and communication board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
3U CompactPCI-Serial Peripheral Boards
Advantech offers different function modules compliant with the PICMG_CPCI-S_0_R2_0 standard.
-
product
Digital I/O Board
CPCI-1500
16 digital inputs, 24 V, including 14 interruptible inputs 16 digital outputs, 24 V, 500 mA/channel Optical isolation 1000 V Input and output filters Watchdog, timer After power-on the outputs are reset to ì0î
-
product
Single Board Computers
ITX-F-3800
WINSYSTEMS’ tiny ITX-F-3825 Series single board computers pack an impressive feature set into an ultra-small form factor Femto-ITX design at just 84mm x 55mm. This SBC is based on Intel’s E3825 processor which provides CPU and graphics performance.
-
product
Customized Test Fixtures
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
product
ARM LPC2468 Board
MS 1511
- 32 Bit ARM7 LPC2468 Processor (128KB SRAM, 512KB FLASH)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports- High Speed Logic Device- External Bus Interface (15 bit address bus and 16 bit data bus)
-
product
PC/104 OneBank Board
EMC2-ZU4EV
Sundance Multiprocessor Technology Ltd.
The EMC²-ZU4EV is a PCIe/104 OneBank™ SBC with a Xilinx Zynq SoC and a VITA57.1 FMC™ LPC I/O board. The main processing power of the EMC²-ZU4EV is a Dual Core ARM9 and combined with traditional FPGA fabrics/gates + High-Speed I/O interfaces, like USB2.0, HDMI, 1Gb Ethernet and SATA and provide an total solution for any Embedded Application.
-
product
MIPI Test Fixtures and Tools
In order to support our MIPI test services, UNH-IOL has designed and created test fixtures and software tools to aid in performing C-PHY, D-PHY, DSI, and CSI-2 testing.
-
product
Serial I/O Boards
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
product
3U CPCI CPU Boards
Advantech 3U CPCI boards are Intel based CPU blades that support single or dual processors that fully utilize I/O features of Intel® chipsets.
-
product
PCI Multi-Functions Board
PCI-DSP-6713-MFIO
The board consists of private SDRAM and dual-ported SRAM attached to the DSP. An FPGA provides the timing and control as well as I/O drive for the 48 programmable I/O pins. Peripherals include a serial port and an USB port. Flash memory is available for downloading programs into a non-volatile memory. 16 channels of A/D and 16 channels of D/A provide analog interfaces to real-world signals
-
product
Large Board Stencil Printer
MC1200
Manncorp's MC1200 SMT large board stencil printer fills application requirements of large-board assemblers with print areas ranging from two feet to nearly four feet in length, making them ideal for LED, backplane and multi-panel assemblies. These big-board printers, priced at one-half to as much as two-thirds less than competing large-board printers, are ideal replacements for slower and less accurate manual printers.
-
product
Single Board Computers
SBC
Our single board computers (SBCs) include versatile mezzanine sites for custom I/O processing and off-board processing. Each processing node is equipped with the best compute power from their respective device generation and are fully interoperable with similar form-factor, OSA and fabric building blocks for low-risk processing subsystem pre-integration.
-
product
Manual Fixture Kit
230354 – CMK-05
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Single Board Computer
VPX3-131
Curtiss-Wright Defense Solutions
The VPX3-131 3U OpenVPX Power Architecture Single Board Computer (SBC) combines the performance and I/O capabilities of NXP's P4080 QorIQ Octal processor with an extensive I/O complement to provide a highly capable processing platform for a wide range of rugged, embedded military and aerospace applications.
-
product
RF Chamber Fixtures
- 12” W x 12” D x 8” H internal dimensions- RF mechanical chamber can fit various wireless and Bluetooth products- test either commercial or consumer
-
product
Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits
upj10
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
product
Monitor SDR Boards
Multiple Access Communications Ltd.
MAC Ltd’s MONITOR product family includes a number of software-configurable digital signal processing platforms intended for use in radio frequency (RF) receiver and transceiver applications. The MONITOR products are available in assembled printed circuit board (PCB) form for integration into larger systems. They also form the basis of MAC Ltd’s CatchAll™ radio products. In addition to the standard products listed below, MAC Ltd is happy to discuss the customisation of existing products and/or the development of new bespoke hardware and software.
-
-
product
ICT/FCT-Fixtures Max UUT 370 × 300 mm (wxd)
CK-2 Large (Hold-Down Gate) / 230158
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
product
Thunderbolt V-600 Board 8-Slot
The 6U VME Thunderbolt boards provide optimal performance and reliability. The Thunderbolt V-600, configured with one Compute Module of four MPC7410 processors, provides 16 GFLOPS of computational performance per 6U VME slot. Data is transferred throughout the Thunderbolt over the SKYchannel Packet Bus. Data moves transparently through the SKYchannel P2 interface to other boards in a SKYchannel chassis.
-
product
VPX Boards
VPX boards (VITA 46) are ideal for high-performance industrial, defense, scientific research, and telephony systems requiring high-speed I/O with serial fabric interconnect technologies. Carrier cards with PCI Express provide a simple and cost-effective solution for interfacing a PMC or XMC I/O modules to a VPX computer system. VPX FPGA modules offer great flexibility and performance for custom computing applications. Depending on your system’s operating environment, you can select air-cooled, conduction-cooled or Ruggedized Enhanced Design Implementation (REDI VITA 48) versions.
-
-
product
cPCI Load Boards
VECTOR Electronics and Technology, Inc.
Vector Electronics & Technology, Inc. cPCI resistive load boards provide a means to test power generated and cooling capability of cPCI systems.
-
product
Drop-In Functional Test Fixtures
Circuit Check’s drop-in base fixture and replaceable personalized plates are the ideal solution where production volumes are lower and the need to change from one fixture and test program to another occurs quickly. Interchangeable test fixture drop-ins enable the same test system to be quickly reconfigured with different tooling and probe patterns for different products. This maximizes equipment re-use, while minimizing the cost for each new test. With Circuit Check’s base fixture and drop-ins, the wiring and test electronics are not disturbed, thus ensuring configuration consistency each time the system is re-tooled.
-
product
Through Connector Functional Test Fixtures
Circuit Check is a pioneer in the development and implementation of access mechanisms enabling testing of circuits through on-board connectors.
-
product
RTAX/RTSX Adaptor Boards
Aldec and Microchip have joined together, offering a new, innovative, reprogrammable prototyping solution for Microchip RTAX-S/S and RTSX-SU space-flight system designs. Unlike the traditional OTP (One Time Programmable) anti-fuse space-qualified FPGAs, the Aldec prototype adaptor uses flash-based, Microchip ProASIC®3E FPGA technology, for design prototype re-programmability.
-
product
Absolute Length Gauges For Measuring Stations And Multi-gauging Fixtures
ACANTO series
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
