Bare board Fixtures
accurately position and retain unloaded PCBs.
See Also: Bare Board Testers, Board Test Fixtures, Bare Board
-
Product
Hall Sensor Board with I2C Interface
048-368
-
Version: +5V/60A +5V/60A +3,3V/25A +12V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Digital Expansion Board
MSXB 013
-
Digital Expansion Boards. The MSXB 013 Digital Input/Output Expansion Board expands 16 digital input lines and 16 digital output lines to 64 digital input lines and 64 digital output lines.
-
Product
ARM LPC2364 Board
MS 1541
-
- 128KB On chip Flash- 16*2 line LCD Module interface- Two CAN channel at 1MPBS- Ethernet interface which supports 10/100 MBPS- Full Modem RS232 interface- RS485 interface- RTC (Real Time Clock)- 2048 bits serial EEPROM with data protect and sequential read.- 24 ULN outputs of 12V level.- Eight 110V DC inputs interface.- Six digital inputs interface- Four on board keys interface- Power delay circuit for external use- ON board inspection circuit
-
Product
cPCI Load Boards
-
VECTOR Electronics and Technology, Inc.
Vector Electronics & Technology, Inc. cPCI resistive load boards provide a means to test power generated and cooling capability of cPCI systems.
-
Product
Hall-Sensor Board with analog output
041-970
-
The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
-
Product
Interface Board for 100 BaseT Ethernet
40-965-911
Interface
The 40-965-911 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 8 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of 100 BaseT Ethernet signals.
-
Product
SparkFun GPS-RTK Board
NEO-M8P-2 (Qwiic)
-
With GPS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GPS Real Time Kinematics (RTK) has mastered dialing in the accuracy on their GPS modules to 25mm, and that's why we had to put it on this board!
-
-
Product
HIL Breakout Board
-
Onboard 192 pin snap-in terminal dramatically simplifies the wiring between your control hardware and your HIL system. As soon as the system is up and running there are 192 test terminals for easy access to all the interface signals: firing pulses, control feedback signals and other analog/digital I/O signals.
-
Product
Isolated Programmable Multifunction Counter Board
APCI-1710
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
Standard Pattern Generator Board
BL-PG315-01
-
The MicroImage PG315 pattern generator is designed for simple size and geometry reference applications. The PG315 will overlay one of five standard patterns including a centered cross line, a centered cross hair, a centered target style symbol, a dot grid (cross dot) array, a hatch grid (crosshatch) array.
-
Product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
Amplifier
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
VPX Boards
-
VPX boards (VITA 46) are ideal for high-performance industrial, defense, scientific research, and telephony systems requiring high-speed I/O with serial fabric interconnect technologies. Carrier cards with PCI Express provide a simple and cost-effective solution for interfacing a PMC or XMC I/O modules to a VPX computer system. VPX FPGA modules offer great flexibility and performance for custom computing applications. Depending on your system’s operating environment, you can select air-cooled, conduction-cooled or Ruggedized Enhanced Design Implementation (REDI VITA 48) versions.
-
Product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-F
-
Breakout board for the Sensirion SHT31-DIS-F with a built-in permeable membrane filter. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
Product
Topside Probing In-Circuit Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Product
HUSKIE 2.0 roboRIO MXP Expansion Board
FRC3061-MXP2-R1
-
The Huskie Board, designed by FRC Team 3061, is an FRC qualified expansion board for the NI roboRIO robotics controller. In addition to breaking out all available signals on the MXP expansion port, this board uses a Parallax Propeller IC (8 symmetrical logical cores with shared memory and peripheral access) to enable tasks such as advanced data logging, on-field driver control and status, and NeoPixel control. Additional GPIO and analog inputs are added with open source code to allow further customization.
-
Product
Digital I/O Board
3512
Digital I/O Module
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
Topside Probing for Functional Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
Product
PCIe Board
Solar Express 200 (SE200)
-
Sundance Multiprocessor Technology Ltd.
Solar Express 200 (SE200) is x8 Gen3 PCIe carrier board with two SoM-PF m(System on Module) sites. The 2 SoMs that can be supported on this carrier are SoM-PF1 and PF2 which are based on MPF500-1FCG1152 and MPF300T-1FCG784E respectively.
-
Product
PC104 MIL1553A & MIL1553B Board
MS 1701
-
*Bus Interface - Standard ISA Bus (PC104 Interface)*One Dual Redundant MIL-STD-1553 Channels, Enhanced Mini-ACE BC/RT/MT Architecture*A periodic message insertion, Real-time bus playback with RT edit mode*Highly Autonomous Bus Controller Architecture, Message Scheduling*Bulk Data Transfers, Data Block Double Buffering*Asynchronous Messages, Retries and Bus Switching*Transformer or Direct Coupled 1553B Channels
-
Product
Mechanical Test Fixtures
MMI series man-machine interface
-
Designed to meet the needs of the most discerning customers and the latest market demands, our MMI series guarantees a natural posture for both the operator and the sitting position when performing the test on the adapter. The newly developed lever mechanism, which has been registered as a utility model, is specially adapted to the hand movement of its employee and ensures a heart-loving strain on the operator.
-
Product
Interface Board for Conduction Cooled PCI Mezzanine Card Systems
EXC-708ccPMC
Interface Card
The EXC-708ccPMC is an ARINC-708 /453 interface board for conduction cooled PCI Mezzanine Card systems. The board supports two or four ARINC-708 /453 channels. Each of the channels can be programmed either as transmit or receive. Each channel implements an 8K×16 FIFO and supports polling and / or interrupt driven operation.The EXC-708ccPMC comes complete with C-driver software library including the source code.
-
Product
8-Channel Relay Output Board With Housing for Mounting on a DIN Rail
PX8500-G
-
The PX8500 is an external 8-channel relay board for the connection of digital output boards. It can be cascaded in 16, 24 and 32 relays and is intended for mounting on DIN supporting rails. The board provides a convenient interface between an industrialprocess and the SUB-D connectors on ADDI-DATA boards. The change-over contacts of the relay are controlled through 24 V signals. The 24 V voltage supply is protected through varistors and transil diodes. The board is intended for the use with 220 V supply. The creeping distance (acc. to DIN VDE0110) and the connector cross sections allows high-power switching (up to 2,500 VA).
-
Product
Virtex 5 Based PXIe Board.
SMT700
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
3U CPCI I/O & Comm Board
3U cPCI 75C5
Multifunction I/O
NAI’s 75C5 is a 3U cPCI Multifunction I/O and Communication Board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed Analog-to-Digital (A/D) channels and 28 Discrete I/O programmable channels, or with a reference power supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
3U PXI Express Board
SMT703
-
Sundance Multiprocessor Technology Ltd.
The SMT703 is built around a user programmable FPGA architecture that features the latest Xilinx Virtex 5 FPGAs. It is supported with two WiMAX RF transceivers that in turn are supported with a mixed signal front-end that integrates dual 12-bit ADCs and dual 12-bit DACs.
-
Product
4" EPIC Single Board Computers
Single Board Computer
4" EPIC embedded SBCs measure 165 x 115 mm, offer scalable high-performance Intel Core™ Processors, rich I/O, compact design, and increased longevity.
-
Product
Power Interface Board 6U, 2 PSU connectors
106PIBM602-0000R
-
The PIB 6U 2 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Pico-ITX Embedded Board
-
The Pico-ITX board is the world’s smallest x86 embedded board, measured at the size of 100 mm x 72 mm only. The Pico-ITX SBC provides system developers and OEMs with an ultra compact yet highly integrated platforms that deliver excellent computing performance at remarkably low power consumption. For car PCs, in-flight entertainment systems, industrial automation systems and even portable devices, the Pico-ITX SBC meets customer's demands in compact-size, fanless operation, low power consumption and versatile I/O.
