Filter Results By:
Products
Applications
Manufacturers
-
product
Topside Probing for Functional Test Fixtures
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
product
RF Shielded Fixture
A semi-automatic, pneumatically operated fixture with a sliding pressure top provides a very short mechanical cycle-time. The unit is prepared for full, multi-station automatic operation using a centrally placed robot arm for UUT load/unload.
-
-
product
MCB Endurance Test Bench
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
product
Topside Probing In-Circuit Test Fixtures
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
Pneumatic Comparator
Huaxin Instrument (Beijing) Co., Ltd
The vacuum pressure comparator is fitted with a differential pressure port that enables connection of gauges under test by hose.
-
product
Pneumatic and electro-pneumatic controllers
Pneumatic-mechanical sequencer and command module. Stepper. Control block for two-hand start. Local controllers
-
product
Pneumatic Hand Pumps
AMETEK Sensors, Test & Calibration
Our pneumatic hand pumps generate pressure and vacuum with precision and ease, allowing users to fine-tune the pressure delivered with every stroke. A built-in vent valve and dual pressure output enable safe and simple operation. Five different models are available to produce vacuum to 580 psi / 40 bar. Each pump is available on its own, or in one of our complete ready-to-use pump systems.
-
product
Pneumatic Sample Press
TF515
TESTEX Testing Equipment Systems Ltd.
Pneumatic Sample Press, a new type of desktop sample press, to cut samples for testing or other use. Equipped with 125 mm cylinder, Cutting depth of 10mm and 125 x 125mmn tables. Under the pressure of 100 psi can produce 800kg/f pressure, equipped with a double bond security operation. Can be requested to provide special shape die. Laboratory standards compression air is required.
-
product
Pneumatic Flat Grips
For tensile testing rubbers, plastics, elastomers, textiles, cloth, and paper, in specimen geometries such as plates, films, and wires, a good option is pneumatic flat grips. Quick clamping and a repeatable clamping force are advantages of pneumatic flat grips.
-
product
Fixture Kit
MF300
Due to careful selection of materials, use of modern manufacturing techniques, and supplying the kit "flat packed" for end-user assembly, Merifix fixtures kits are inexpensive enough to be used in low-volume production and in engineering labs for programming and debug tasks, where traditional fixtures would be too expensive.
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
product
Pneumatic Subsystem
OTP2-Modul-Nr050
With the pneumatic subsystem, a roller terminal, a maintenance unit, a main vent, a pressure reducer and 8 2/3-way vents are installed in the system. The extension of the module can create new possibilities for your test system.
-
product
Functional Fixtures
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
product
Test Of Hand Pneumatic Tools
The measuring system consists of a test site and a control rack. The test site is equipped with a mounting for the test tool with measuring sensors: vibration, torque and speed, as well as a pneumatic regulator, a filter and a powder type brake clutch. The maximum torque test is performed until the rotation is completely stopped. The screen displays both the directly measured maximum torque and the calculated maximum power of this sample. At the end of the test, the results are presented to the operator on the monitor screen.
-
product
Fixturing Kit
10744A
The Keysight 10744A fixturing kit includes mounting hardware for a variety of Keysight measurement optics devices. A large base, multiple posts, and other accessories let you build structures -- such as tall, rigid towers -- that place optics in the center of a machine's work zone or wherever needed. The fixturing kit helps meet the physical requirements of a range of measurement applications.
-
product
Pneumatic Type
Concentric Technology Solutions, Inc.
The Pneumatic Operation series of shield boxes provides superior performance for efficient RF isolation test environment for testing mobile, WLAN and other small RF devices. Its pneumatic controls to open and close the lid can be controlled manually or with a remote control for semi-automatic operation.
-
-
product
Manual Fixture Kit
230354 – CMK-05
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Pneumatic Zero Drop Tester
HIACC Engineering & Services Pvt. Ltd.
Designed as per ISTA packaging standard, the Pneumatic Zero Drop Test stand is used to assess the drop bearing capacity of the specimen during its transportation and handling process. The system is ideal for testing the specimen vulnerability around edges, surfaces and corners at different heights.
-
product
Electro Pneumatic Circuit Employing PLC
Unitech Scales And Measurements Pvt. Ltd
* Study of PLC and its accessories. * All above circuits. * Introduction of timer, counter in all above circuits. * Interfacing PLC with Mimic panel. * Many circuits used in Washing Machine, process controls, drilling machines, etc,.
-
product
Universal Test Fixture
Series 48
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
product
Manual Fixture Kit
230372 – CMCSK-03-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Stiffness Tester Pneumatic
TF114
TESTEX Testing Equipment Systems Ltd.
Fabric Stiffness Tester Pneumatic, used for testing the stiffness of fabric by the bending cycle test method of ASTM.
