-
Product
Pneumatic, Contact, Receiver (with valve), Hose Barb, for 1/8" [3.2 mm] ID Tubing
610131107
Pneumatic Contact
Primary mating contact 610131106.Used in receiver module p/n 510104185, mates to contact p/n 610131106 and ITA modulep/n 510108160.
-
Product
Test Fixtures
-
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Product
Pod/Nest Fixtures
-
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
-
Product
Clamshell Type Mechanical Fixtures
Series 31
-
The GR Series 31 dual well mechanical kits provide a solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility and the advantage of testing two devices on the same test fixture. These can be similar devices, or devices that are used together in a functional test.
-
Product
Pneumatic Multipliers
CLS
-
The CLS pneumatic torque multiplier provides precision tightening and loosening of all heavy duty fastening connections. The torque multiplier shuts-off when pre-set torque is achieved. It's a non-impacting and operates at a smooth, continuous rotation, the torque multiplier increases speed and productivity, as it is faster than a hydraulic wrench and is less expensive.
-
Product
Custom PCB Test Fixtures
-
Emergent Electro-Mechanical designs and manufactures customized test fixtures and burn-in racks. Each of our custom designs is unique to our customer's particular project requirements. Emergent fixtures feature innovative design components including a linear collapsing system, interchangeable and reusable plate design, and top and bottom probing.
-
Product
Flexible Pitch GND Fixture Clamps
GF-A
-
High Power Pulse Instruments GmbH
*Compatible with GGB picoprobe model 10 replacement probe tips*<1 ns rise time (200 ps possible with 5 mm GND wire length)*Custom selectable GND wire length 5-15 mm*Gold-coated spring-steel clamp with micro-machined groove for locking of the clamps on the probe tip*High conductivity and low inductance copper HF litz wire with 200 x Ø 0.02 mm strands*Easy to use clamping*Tungsten carbide probe needle with 1 inch length, 15° taper and 7.5 µm tip radius
-
Product
PCB Test Fixture Kits And Customized Fixtures
-
Mirotech manufactures portable benchtop PCB test fixture kits and provides customized test fixture solutions for the electronics industry. Our innovative, streamlined designs are compact in size and feature a linear collapsing system, interchangeable and reusable plate design, top and bottom probing, and are affordably priced. All fixtures are built using high quality hardware and materials and manufactured using the DATRON M8Cube, known for its precision and accuracy. Each of our custom designs are unique to our customer’s particular project requirements. Fixture kits come pre-assembled, and include blank plates ready for you to drill your test pattern.
-
Product
Stiffness Tester Pneumatic
TF114
-
TESTEX Testing Equipment Systems Ltd.
Fabric Stiffness Tester Pneumatic, used for testing the stiffness of fabric by the bending cycle test method of ASTM.
-
Product
Absolute Length Gauges For Measuring Stations And Multi-gauging Fixtures
ACANTO series
-
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
-
Product
(ITA), Breakout Box & Fixtures
ITA
WinSoft provides a wide range of Interface Test Adapters (ITA) and test fixtures to meet the most challenging functional test and signal conditioning requirements. This includes high frequencies, voltages and current.
-
Product
Cable Continuity Test Fixture
CCT
-
6 and 8 Wire Cable Continuity Test Fixtures For convienient desk top and bench top The most important features of this cable continuity tester is its ease of use intuitive control functions and durability in a production environment.
-
Product
EBIRST 8-pin Male Power D-type Termination Fixture
93-012-103
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Pneumatic and Hydraulic Characteristics Test
-
Pneumatic and hydraulic testing is performed to demonstrate operating pressure, pressure drop, volume and flow parameters, as well as performance characteristics, of fluid system components and assemblies.
-
Product
Exchangeable Test Fixture
MA 2109/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg
-
Product
Vacuum-Pneumatic, Module, Receiver, 90 Series, 1 Pos Vacuum, 2 Pos 3/8" ID Pneumatic
510104276
Receiver Module
Primary mating module 510108264.
-
Product
RF/Wireless Test Fixtures
-
Test‐Head Engineering develops and manufactures RF Test Fixtures which allow the testing of RF and Wireless modules and components.
-
Product
TRUE Z-AXIS CAM ACTIVATED TEST FIXTURE KITS
-
The Cam Press is designed to provide precise, bed-of-nails contact, in a production test environment. Durable aluminum and steel construction and precision bearings insure accuracy and repeatability sufficient to contact test points as close as 10-mils center-to-center.
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
Manual Fixture Kit
230352 – CMK-03
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Custom Test Fixtures
-
For popular high speed components like semiconductor packages, and test contactors, we have developed a custom test fixture which allows the use of high bandwidth microprobes to measure virtually any I/O pin, according to GigaTest's methodology and requirements.
-
Product
ARINC HSI / ADI Test Fixture
TA-2000
-
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
Product
Stand-Alone Test Fixture
MA 2013/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 22,00 kg
-
Product
Test Fixtures & Jigs
-
A test fixture or test jig is the component containing the bed of nails used for testing the PCB or assembled product. It is powered and controlled by the Yelo Testpoint system which has test cards capable of providing multiple test conditions. This system also controls the probes used in the bed of nails, and relays test information back to the Testpoint system to be analysed.
-
Product
Pneumatic Transmitter
-
Indicating pneumatic transmitter assists in the coordination of key functional areas within facilities. Transmitting data efficiently and accurately, it ensures operating economies and safety. A good product for process control and monitoring.
