Audio Amplifiers
This topic is for test equipment that is designed for the testing of audio amplifiers.
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Saluki SE1022D DSP Lock-In Amplifier (Dual-channel)
-
SE1022D Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. More importantly, SE1022D has dual independent input channels and dual independent high precision signal generators. Each input channel and signal generator can be used independently which means that the SE1022D is equivalent to two traditional lock-in amplifiers. Moreover, due to the twin symmetrical design, the two independent input channels and signal generators have ultra-high synchronicity, which meets the measurement requirements demanding extremely high synchronization.
-
Product
RF Bidirectional Amplifiers
-
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
Product
Light Sources and Amplifiers
-
Light sources simulate the optical voice, video and data signals of real-life service applications, which is why they are used in various types of tests. Discover a broad range of products that cater to various testing requirements: singlemode or multimode, polarized or non-polarized, broadband or narrowband, tunable, ITU-wavelength-centered and much more.
-
Product
Charge Amplifier
-
This compact Charge Amplifier has 3 signal routes.When it is used as the Charge Amplifier for the vibration analysis systemWave Stocker, all setups are possibleby the upgraded software.
-
Product
Single Channel High Voltage Linear Amplifier
F20A
-
The F20A is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of ±150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Audio Analyzer / Studio Aid
MiniSonic MS10
-
The MiniSonic MS1/MS10 Audio Analyser/Studio Aid is a complete, hand held, two-channel analogue audio test set that measures frequency, frequency response, phase, level, noise, distortion, crosstalk, speed and path latency (delay).As well as being a quality tester it's a precision line-up tool, a stereo PPM, a balanced-unbalanced convertor (both ways),a stereo mic preamp, a headphone amp, and a level convertor.
-
Product
Fully Differential Amplifiers
-
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
Product
Time & Frequency Distribution Amplifiers
-
Brandywine offers a wide range of high quality, state of the art signal timing distribution amplifiers, all with very low phase noise. These precision timing signal distribution amplifiers offer a variety of time and frequency signals and interface formats including IRIG A, IRIG B, Have Quick, 1PPS, as well as low phase noise reference frequencies. All of our distribution amplifiers feature dual inputs with automatic failover and multiple independently buffered outputs.
-
Product
RF Amplifiers up to 1000 MHz
-
Narrow and Broad band high power RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAs in Class A and Class A/B topologies for Pulse, AM, FM, continuous wave and digital modulation applications that include EW, Radar, Jamming, EMI and EMC radiated immunity, and wireless communications testing.
-
Product
Amplifier Built-In/U-Shaped Micro Photoelectric Sensor [Compact/Connector Built-In Type]
PM-65
-
Panasonic Industrial Devices Sales Company of America
The Panasonic PM-65 Sensor has a beam emitting / receiving distance of 6 mm. The beam emitting and receiving areas are 0.5 mm thinner compared to conventional models even though the external dimensions have not changed. As a result, the distance between the beam-emitting and the beam-receiving points have increased by 1 mm thereby reducing the possibility of sensing objects colliding.
-
Product
40mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
Audio Analysis
-
The MCD AudioAnalyzer is used to test and calibrate analog and digital sound systems, or it can be used to convert analogue audio signals into digital form and vice versa. Also, the conversion of optical to electrical S / PDIF signals and vice versa can be done. The MCD AudioAnalyzer combines software (Toolmonitor MCD AudioAnalyzer) and hardware for the analysis and generation of analog and digital signals in the audio area.
-
Product
Pico-ITX SBC With Intel® Atom® Processor E3845/E3827, LVDS/ VGA (HDMI), LAN And Audio
PICO840
-
The PICO840 ultra-small Pico-ITX embedded SBC supports the quad-core Intel® Atom® processor (code name: Bay Trail-I) and supporting DDR3L-1066/1333 MHz system memory up to 8 GB. Considering different environments, this industrial-grade Pico-ITX mainboard is built to withstand extreme temperature, ranging from -40°C to +70°C (-40°F to +158°F). Moreover, with superior integration and power efficiency, this compact size single board computer enables system developers and OEMs to create smaller, lighter, quieter devices than ever and embrace the new possibilities across POS systems, mobile medical monitor, compact panel PCs as well as multiple embedded computer, system and appliance segments.
-
Product
RF Amplifiers
-
UST specializes in the testing, repair and refurbishment of all types of RF amplifiers (broadband and narrowband), microwave amplifiers and millimeter-wave amplifiers: solid state, thin film, traveling wave tube (TWT), low noise RF amplifiers, intermediate power RF amplifiers, limiting RF amplifiers, doubler RF amplifiers, driver RF amplifiers, variable gain RF amplifiers, and active frequency multipliers.
-
Product
Monitor Unit For PAV Series 4-Quadrant Power Amplifier Monitor
-
The 4-Quadrant Power amplifier monitor unit is an optional unit of the PAV series of 4-quadrant amplifiers, which can be assembled into the cabinet.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
Overdrive Protected Amplifier
-
RF Lambda’s line of overdrive protected amplifiers incorporate a technology which eliminates the need for a limiter to protect the amplifier from damage. High input powers up to 10W can be injected in the amp without damage. Hermetically sealed options are available upon request.
-
Product
4-Quadrant Power Amplifier For Simulation Applicaton
PAV20000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Pico-ITX SBC With Intel® Atom® Processor E3845/E3827, LVDS/VGA, LAN And Audio
PICO841
-
The PICO841, an extreme compact embedded pico-ITX motherboard, is designed to support the latest 22nm quad cores Intel® Atom® processor E3845 or dual cores E3827 (codename: Bay Trail) with one DDR3L system memory maximum up to 8 GB. With its compact size and ultra-low power consumption, it is perfect for space-limited and power saving environments. Otherwise, the energy-efficient embedded board is built to withstand wide temperature conditions, ranging from -20°C to +70°C (-4°F to +158°F). Integrated with Intel® HD graphic engine, the PICO841 supporting VGA and 18/24-bit dual channel LVDS in dual-view provides faster and better graphic performance. Furthermore, to increase the connectivity and reliability, the rich feature of I/O interfaces are integrated to allow flexible cabling. Coming with two PCI Express Mini Card sockets, the pico-ITX mainboard offers excellent extensibility.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-816
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
Gain Shape Linearizer Amplifiers
-
Gain Shape amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Product
Audio Frequency Output Power Meter
-
PGP Electronics Private Limited
PGP Electronics AF Output Power meter, model 3301provides reliable measurement of Audio Frequency Output Power. The audio power output meter, measurable from 0.01mW to 30W in 12 decades with 10 different termination impedances with both balanced and un balanced inputs. The instrument is very useful to conduct students projects, design and test simple sub systems in laboratories. New improved design features provides reliable working even in adverse environments.
-
Product
Amplifiers
-
Use our optical amplifiers to improve the signal-to-noise ratio (OSNR) and range performance of optical transmission systems.
-
Product
Amplifiers - Solid State
-
PMI offers a full line of RF and Microwave Amplifiers that range from 250 kHz up to 50.0 GHz. Many options are available. If you do not see exactly what you require on this website, please contact sales@pmi-rf.com because we offer amplifiers designed and built to your specifications at catalog prices.
-
Product
Ka Band Power Amplifier
-
The ERZ-HPA-2000-4500-24 is a Ka Band Amplifier providing an output power of 24 and a gain of 22 dB. The compact size and modularity makes it ideal for a wide range of applications. Frequency Range (GHz): 20,00 to 45,00.
-
Product
DC-Coupled Pulse Amplifiers
-
These DC-coupled pulse amplifiers are available in a simple DC-power module format, and are also available in an AC-powered benchtop instrument format. All models will drive a 50 Ohm load.
-
Product
Digital Audio Snake System
OmniSnake
-
The OmniSnake consists of a Stage Box that converts microphone/line-level analog inputs to a multiplexed digital signal, and a companion Base Unit that de-multiplexes to provide individual outputs. Digitizing the analog audio at the source eliminates the potential for ground loops, noise interference and crosstalk. Each Stage Box has 8 inputs, and two Stage Boxes can be linked together via coax to form a combined 16 channels, which is carried over coaxial cable to the Base Unit.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
-
Product
1×6 Video Distribution Amplifier
VDA206 S-Video
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
