ATE Fixtures
Holding and positioning assemblies to guide UUT I/O access by automated test equipment.
See Also: Test Fixtures, PCB Test Fixtures, Board Test Fixtures
-
Product
Test Fixture and Test Programing
-
Landrex Technologies Co., Ltd.
Test Fixture and Test Programing
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
Deep And Sloped Pan Fixtures
-
Line of deep and sloped pan fixtures for general purpose/system non-specific pcb test applications. H+W Test Products manufactures test fixture products for in-circuit, functional and combinational testers for users of automated test systems (ATE) such as Aeroflex, Agilent (HP), Checksum, Factron, Teradyne (GenRad), Test Research (TRI) and Testronics.
-
Product
Edge Connector Fixture
EDGE
-
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
Product
TRUE Z-AXIS CAM ACTIVATED TEST FIXTURE KITS
-
The Cam Press is designed to provide precise, bed-of-nails contact, in a production test environment. Durable aluminum and steel construction and precision bearings insure accuracy and repeatability sufficient to contact test points as close as 10-mils center-to-center.
-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
Product
Magnetizing Fixtures
-
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
Product
Topside Probing for Functional Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
Product
Functional Test Fixtures
-
Intrinsic Quality delivers turnkey standalone Functional Test fixtures and Windows based functional testers that are custom engineered with innovation and reliability to meet your testing needs. Our experience and expertise ensure a production ready functional test solution that is cost-effective, on time and on budget. Our broad range of test solutions includes simple continuity testers to complex microcontroller assembly testers. Our customers include military, aerospace, automotive, medical and consumer OEMs. We serve the needs of low volume high mix CEMs and off shore high volume manufacturers.
-
Product
Board Test Fixture Probes
-
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
Product
Clamshell Type Mechanical Fixtures
Series 70
-
The VP Series 70 Mechanical Test Kits provide a solution to printed circuit board testing using the Virginia Panel ITA G12 Interface.
-
Product
EBIRST 100-pin SCSI Termination Fixture
93-019-104
Termination Fixture
93-019-104 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
-
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
Product
Custom PCB Test Fixtures
-
Emergent Electro-Mechanical designs and manufactures customized test fixtures and burn-in racks. Each of our custom designs is unique to our customer's particular project requirements. Emergent fixtures feature innovative design components including a linear collapsing system, interchangeable and reusable plate design, and top and bottom probing.
-
Product
In-Circuit Test Fixtures
-
In-circuit testing provides electronic manufacturers a reliable, high fault coverage verification method for the assembly process. Circuit Check ICT fixtures are robust, reliable and designed for easy customization to cover a large range of PCB sizes without impacting turnaround time. We stock a large variety of fixture sizes and actuation methods to meet your test demands. If a stocked sized ICT fixture is not adequate our engineering staff will design a custom solution.
-
-
Product
Automatic Fixture Removal
S96007B
-
Automatic fixture removal (AFR), is the easiest way to remove fixture effects from non-coaxial device measurements.
-
Product
Manual Fixture Kit
230373 – CMCSK-04-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
-
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
-
Product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 230 x 175 mm (wxd)
CMK-06
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Flexible Pitch GND Fixture Clamps
GF-A
-
High Power Pulse Instruments GmbH
*Compatible with GGB picoprobe model 10 replacement probe tips*<1 ns rise time (200 ps possible with 5 mm GND wire length)*Custom selectable GND wire length 5-15 mm*Gold-coated spring-steel clamp with micro-machined groove for locking of the clamps on the probe tip*High conductivity and low inductance copper HF litz wire with 200 x Ø 0.02 mm strands*Easy to use clamping*Tungsten carbide probe needle with 1 inch length, 15° taper and 7.5 µm tip radius
-
Product
Automatic Fixture Removal
S93007B
-
The S93007B automatic fixture removal (AFR) is the easiest way to remove fixture effects from non-coaxial device measurements and runs on the PNA/PNA-L/PNA-X Series B model network analyzers
-
-
Product
Standard & Custom Test Fixtures
-
Both standard and custom Test Fixtures from OAI enable the user to integrate the solar cell with the I -V tester. Fixture configurations range from from simple hold down devices to temperature-controlled fixtures with front and back side contact. We invite you to contact an OAI Application Engineer for help with your fixture design. With our expert guidance, you can expect maximum performance from your I -V Tester and Solar Simulator.
-
Product
USB A TX Test Fixture
AUT20135
-
This newly designed AUT20135 brings enhanced user-experience with the following features:
-
Product
In-Circuit Fixtures
-
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
Product
USB-C® Short Channel Rx Precet. Test Fixture
AUT20098
-
*Easy swap between CC1 and CC2RP & RD Mode: In the older version of the USB-C full breakout board, users had to manually set the jumper with a short pin. But now users can easily swap between the two by just moving the switch.*In the previous version, the soldering joint of Test Fixture Host Fixture 1A gets worn out quickly from repetitive plug and pull. This newly designed fixture is more durable and users can easily replace the worn out SMA connectors with new ones.*DC-in Jack is upgraded to +5V USB C portA boost in user experience as it makes setting up easier.
-
Product
Functional Test Fixtures
-
Test Head Engineering's Custom Functional Test Fixtures range from simple to extremely complex. Typically, our customers do their own wiring and programming, but we will complete the job right up to the customer's requirements, including offering turn-key control and test programming through our partners.
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
Emergency Battery Test Fixture
TA-60
-
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
