D-Sub
D-Subminature Connector Also known as: DSub
-
Product
Breakout Box
T1000-37
-
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
Product
PCI Daughter Boards
DB-8425
-
Connector interface for PISO-DA2Screw terminals for easy field wiring9-pin D-sub connector pin to pin screw terminal for PISO-DA2
-
Product
8 Pin Power D-Type Female Connector, 40A, With Backshell
40-960-008-F
-
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
Product
9-Pin D-Type, Right Angled PCB, Female, HV
40-963-009-RF-HV
-
9-Pin Female Right Angled D-Type Connector, High Voltage - PCB Mount
-
Product
15' Cable, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97112
-
15' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
SH37F-P-4, 37-Pin Female to Pigtail Shielded I/O Cable, 12ft
778620-04
-
37-Pin D-SUB Female to 37-Pin Bare Wire Female, 12 ft, Pigtail I/O, Shielded Multifunction Cable - The SH37F-P-4 connects compatible CompactRIO modules to accessories or cables with bare wire connectors.
-
Product
SH37F-Tajimi Shielded Cable, 10M
199254-10
-
37-Pin D-SUB Female to 4 7-Pin Tajimi Female, C Series Strain/Bridge Input Module Multifunction Cable - The SH37F-Tajimi connects with compatible sensors to accessories or cables with Tajimi push-pull connectors.
-
Product
Digital I/O Card w/CoS IRQ
mPCIe-DIO-24S
-
The mPCIe-DIO-24S is a type F1 PCI Express Mini Card (mPCIe) and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
25-Pin D-Type Male Right Angled PCB
40-963-025-RM
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 25-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
PCI Daughter Boards
DN-8237
-
DN-8237 is the kit that includes the breakout board and cable for I-8092F. It includes a din rail mountable daughter board (wiring terminal board) for I-8092F and CA-3710D Male D-sub cable 1M Cable for Daughter Board(180°). I-8092F is a 2-axis stepping/pulse-type servo motor control module that can be used on any of the ICPDAS I- 8000, Wincon, and Lincon series controllers, and is suitable for general-purpose motion applications.
-
Product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable, 2m
192061-02
-
68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable - The SH68M-68F-EPM Cable, sometimes referred to as SHC68-68-EPM, connects DAQ devices to accessories or cables with D-SUB connectors. You can use this cable to create custom cabling for your DAQ device. The SH68M-68F-EPM Cable is offered in different lengths.
-
Product
25-Pin D-Type Female Connector Block
92-965-025-F
-
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties.
-
Product
PCI Daughter Boards
DB-8225/2 (with 2 meter D-Sub 37-pin cable)
-
Screw terminal boardusing 37 pin cable I/O ports for A-82X seriesPCI-1800 series. (16 channel single-ended or 8 channel differential)Blank padsfor break detectionlow-pass filtercurrent shut and voltage attenuation.On board cold junction circuit in analog input channel 1jumper selectable single-endeddifferential modeDimensions :118mm x 174mm
-
Product
PCI Daughter Boards
DB-24POR/D (with D-Sub cable)
-
The DB-24POR has 24 channels of optically isolated Photo-Mos Relay , and OPTO-22 compatible connector.
-
Product
50-Pin D-Type Connector, Right Angle PCB
40-963-050-RF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Cable Assembly, Receiver, 36", TriPaddle, 15 Pin FML DSub, 9 Pin FML DSub
540214010201
-
Cable Assembly, Receiver, 36", TriPaddle, 15 Pin FML DSub, 9 Pin FML DSub.
-
Product
Cable Assembly, Receiver, TriPaddle, 72", 37-Pin Female D-sub and 4 POS Micro Fit Connector
540016070501
-
Cable Assembly, Receiver, TriPaddle, 72", 37-Pin Female D-sub and 4 POS Micro Fit Connector.
-
Product
50-Pin D-Conn Female Straight PCB
40-963-050-SF
-
Ideal for user created termination schemes where the termination is to be on the front or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Connector, 104-Pin D-Type Male, Solder Bucket, 5A
40-960-104-M
-
This 104-pin male D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell.
-
Product
9 Pin D-Type, Male, Straight PCB Mount, HV
40-963-009-SM-HV
-
9-Pin Male D-Type Connector, High Voltage - Straight PCB Mount
-
Product
Board Accessories
DN-37A (with Din Rail Mount and Male-Female D-Sub Cable)
-
DN-37 is a Screw Terminal Board for PC Based I/O Boards with or without din rail mounts. It is an I/O Connector Block with a 37-Pin I/O Connector and 37-pin CA-3710 cable.
-
Product
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
782015-02
-
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 50-Pin Female D-Sub
540018010101
-
Cable Assembly, Receiver, TriPaddle, 20", 50-Pin Female D-Sub
-
Product
PCI Daughter Boards
DB-24POR/D/DIN (D-Sub cable and DIN-Rail mounting kit)
-
The DB-24POR has 24 channels of optically isolated Photo-Mos Relay , and OPTO-22 compatible connector.
-
Product
PCI Analog Output Boards
PIO-DA16U
-
14-bit 16 Channel Analog Output Board auto detected by Windows. Includes CA-4002 D-Sub connector
-
Product
PCI Digital I/O Boards
PCI-P16POR16
-
16 Channel Isolated Digital Input, 16 Channel PhotoMos Relay Output. Includes CA-4037W cable and two CA-4002 D-Sub connectors
-
Product
Connector Block, 50-Pin D-Type, Female
40-965A-050-F
-
The 40-965A-050-F connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
