Filter Results By:
Products
Applications
Manufacturers
Trigger Modules
-
product
Radio Trigger Module
RTM3
The Remote Trigger Module 3, or RTM3 3, is a new generation of impact trigger device. It is designed to time synchronize a single seismic source unit with multiple seismic recorders. It can also be used to synchronize multiple seismic recorders. The RTM3 units use an internal high accuracy oscillator that is synchronized to GPS timing information. Each RTM3 unit requires an external GPS receiver with valid satellite information to synchronize the internal clock. Once the internal clock is synchronized the RTM3 can be used without any GPS signal for up to 10 minutes.
-
product
Breakout Module
PXI-PDM
The PXI Preamplifier Power and Trigger Breakout Module (PXI PDM) is an accessory for the Pixie-4 system.
-
product
4-Channel High Speed Position Comparison and Trigger Module
ECAT-TRG4
The ECAT-TRG4 is EtherCAT slave module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications.
-
product
Weight Drop Controller
WDC
The WDC unit consists of the following: *Weight Drop Relay Control System *Radio Trigger Module (RTM) *Remote Control Box *Radio*Hammer Switch The WDC provides following features: *Automatic cycling with user entered number of hits*Time Delay Display (Time from fire command to hit)*GPS interface for position and timing*Remote Control Box
-
product
4-Channel High Speed Position Comparison And Trigger Module
ECAT-TRG4
The ECAT-TRG4 is EtherCAT SubDevice module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications.
-
product
PXI/PXIe Trigger Module
PXT1741
The PXT(e)1741 Trigger Module ist designed to build up a connection between trigger signals from any external trigger source (5V TTL Standard) and the PXI(e) trigger bus. Therefore the device is equipped with four SMA front connectors (T1 to T4).
-
product
4-Channel Motion Control And High-Speed Trigger And Module For The Bridge Connected To EtherCAT
ECAT-4XMO
The ECAT-4XMO is EtherCAT SubDevice module with high-speed position comparison trigger and encoder re-drive function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications. Additionally, the ECAT-4XMO has 4-axis motion control with bridge function between EtherCAT and non-EtherCAT. Advanced motion control functions help machine and equipment builders to increase their motor selection portfolio, like linear, step, servo, direct drive, and AC motors, making it ideal for a variety of automation industry applications.
-
product
Components for System Integration
Bh offers a wide range of accessories to improve your photon counting experiment such as experimental control modules, optomechanics or implantable fiber probes for in-vivo applications. For PMTs and MCPs we offer different preamplifiers and a variety of routing devices for multi-detector operation. For a perfect SYNC signal, trigger modules and a SYG are available.
-
product
PXI/PXIe Trigger-Module
PXT(e)1741
Easy linkage of various external modules to the PXI(e) trigger busHigh configurable trigger matrix12 independent configurable trigger linesInputs/Outputs compatible with 5 V TTL standardSoftware controlled triggering of any target device
-
product
IO60-DIO48 Module
IO60-DIO48
WINSYSTEMS’ IO60-DIO48 Module adds GPIO to embedded systems with IO60 expansion featuring 48 GPIO (General Purpose Input-Output) tolerant to 30 V DC. The SPI interface is implemented through the MACH XO2 SPI-slave EFB (Embedded Function Block) interface. Each bit of each port is implemented as a bi-directional tristate driver. Each bit of each port can also be configured and enabled to detect rising and/or falling edge events and generate a system interrupt.
-
product
Voltage Input Module For Remote I/O
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
product
NI-1483, Full-Configuration Camera Link Adapter Module for FlexRIO
781341-01
The NI‑1483 makes FPGA image processing possible for FlexRIO systems. It supports 80‑bit, 10‑tap base‑, medium‑, and full‑configuration image acquisition from Camera Link 1.2 standard cameras. You can pair the NI‑1483 with a PXI FPGA Module for FlexRIO to perform custom image analysis. FPGA processing is ideally suited for applications that require bit-level processing and very low system latency. Implemented in hardware, FPGA processing does not require CPU intervention. You can process images on the FPGA independently or with a CPU for more advanced preprocessing architectures.
-
product
PXI Carrier Module For SwitchBlock
The PXI Carrier Module for SwitchBlock can hold up to six Matrix Modules for SwitchBlock while occupying four PXI slots. By connecting multiple SwitchBlock relay cards through the carrier's integrated analog bus, you can easily create large matrices with more than 2,000 crosspoints in four PXI slots and more than 8,000 crosspoints in a single PXI chassis. Each Matrix Module for SwitchBlock comes in an A-type version, which serves as the first matrix building block and offers row and column access through the front connector, and a B-type version, which serves as an expansion module and only provides column access through the front connector. Typically, SwitchBlock systems contain one A-type module and numerous B-type modules.
-
product
PXI Prototyping Module, 1-Slot, 78-Pin D-Type
40-225A-401
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
Mini Coax, Module, Receiver, 90 Series, 19 Positions, for use with right-angle contact (p/n 610104160)
510104319
Use with right-angle mini coax contact (p/n 610104160) for mounting to PCBs. Includes holes for PCB mounting.Primary mating module 510108111. (May mate with other ITA modules, as well.)
-
product
PXI/PXIe RF Switch, 8xSP4T + 4xSP4T, 1.3 GHz, 50 Ω, Multiway Connectors
42-755A-902
The 40-755A-902 (PXI) and 42-755A-902 (PXIe) are high density RF switch modules configured as 8xSP4T and 4xSPDT. The range of modules is available in 50 Ω and 75 Ω variants with mixed SP4T & SPDT switches in a single PXI module. They are available with two connector options; SMB that provides a frequency range of 1.8 GHz (50 Ω) / 1.3 GHz (75 Ω), or multiway which limits the bandwidth to 1.3 GHz but offers a high density solution occupying one PXI slot. The connectors used are fully supported by the range of Pickering Interfaces connection solutions.
-
product
SMARC Short Size Module with Intel® 6th Gen. Atom® x6000 Processors (formerly codename: Elkhart Lake)
LEC-EL
The ADLINK LEC-EL is a SMARC module that supports Intel Atom® x6000 (x6425E, x6413E, x6211E, x6200FE, x6425RE) processors (formerly Elkhart Lake) with integrated Intel® UHD graphics and high speed interfaces. LEC-EL modules support up 8GB LPDDR4 memory, and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
product
PXI Breadboard Module, 1-Slot, 25-Pin D-Type
40-220A-301
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
cRIO-9803, Up to 480 GB SSD Expansion Module for CompactRIO
785921-01
Up to 480 GB SSD Expansion Module for CompactRIO - The cRIO-9803 provides a bus-powered USB SATA bridge to a full-length mSATA solid-state drive (SSD). This module uses a USB Type C connector with integrated cable retention. It also works with devices that feature other types of … USB connectors, such as CompactRIO Single-Board Controllers, Industrial Controllers, and PXI Controllers. The cRIO-9803 is available in 64 GB SLC for high endurance in rugged environments, in 480 GB MLC for high-capacity data storage, and for use with a customer-supplied SSD. Additionally, the cRIO-9803 features the same rugged shock and vibration ratings as other CompactRIO modules and can be mechanically connected to a controller for integration using mounting accessories.
-
product
Signal Module, Receiver, QuadraPaddle, 192 Position, Right Angle Contacts For Custom PCB Mounting (510 150 130 And 510 109 315)
510150152
This kit has everything you need to attach a VPC Receiver Module to a custom designed PCB. This includes the right angle header (P/N 510 109 315) and the Receiver Module (P/N 510 150 130).
-
product
C Series Current Output Module
The C Series Current Output Module features up to eight channels of simultaneous analog output. You can choose between enclosed and non-enclosed modules. Additionally, the C Series Current Output Module has built-in open-loop detection. This detection generates an interrupt in software when an open loop is detected, zeros outputs to ensure safety, and avoids driving actuators at system power-on. The C Series Current Output Module requires an external power supply and includes a channel-to-earth ground double isolation barrier for safety and noise immunity.The C Series Current Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
PXI System Synchronization Modules
Keysight's PXIe System Synchronization Module (SSM) provide multi-module/multi-chassis synchronization and triggering for Keysight’s modular systems, as well as other Keysight instruments. They meets the STM specifications documented in the PXI Express Hardware Specification.
-
product
SMARC Short Size Module with NXP i.MX 8M Plus
LEC-IMX8MP
ADLINK LEC-IMX8MP, based on the powerful NXP i.MX8M Plus (quad core Arm Cortex-A53) processor with an optional Neural Processing Unit (NPU) operating at up to 2.3 TOPS., is the first SMARC revision 2.1 compliant module focusing on machine learning and vision, advanced multimedia, and industrial IoT with high reliability. Additionally, it supports dual Image Signal Processors and two camera inputs for an effective Vision System. The LEC-IMX8MP is suited for applications such as smart home, building, city and industry 4.0.
-
product
PXI-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
778572-15
35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXI‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXI‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
Thermocouple, Module, Receiver, ICon, 96 Position
510160110
Thermocouple, Module, Receiver, iCon, 96 Position
-
product
COM Express Compact Size Type 6 Module Intel Atom® E3900 series, Pentium®, and Celeron® SoC (formerly Apollo Lake)
cExpress-AL
The cExpress-AL is a COM Express® COM.0 R3.0 Type 6 module supporting the Intel Atom® processor, Intel® Pentium® processor and Intel® Celeron® processor system-on-chip (SoC). The cExpress-AL is specifically designed for customers who need optimized processing and graphics performance with low power consumption in a long product life solution.
-
product
Signal / Twinax, Module, ITA, TriPaddle, iCon Series, 40/4 Position
510161109
Primary mating module 510160109.
-
product
PXI SPDT Switch: 64-ch, 100 Vrms / 1A, Reed Relays
M9131A
The M9131A is a high-density, general purpose switch with 64 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights, or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100 Vrms and 1 A, with up to 3 W maximum power. Choose from the durable connector block or standard cable connections.
-
product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-01
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
product
PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual SPDT, Unterminated
M9155CH40
M9155CH40 PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual SPDT, Unterminated
