Phase Noise Analyzers
-
Product
Logic Analyzer
Ant18e
-
The Ant18e logic analyzer is compact, easy to use, powerful, and inexpensive. The Ant18e features high speed data acquisition, state (synchronous) and timing (asynchronous) acquisition modes, Trigger-In and Trigger-Out connections, and a user-level programming interface.
-
Product
Logic Analyzer Probes
-
Three probe types are available for GoLogicXL logic analyzers: flying leadset, Mictor, and Pinpoint probes. The Mictor and Pinpoint probes are compatible with similar Keysight/Agilent "soft touch" and Tektronix "connectorless" probes. All GoLogicXL probes are coaxially shielded and use passive termination inputs to prevent loading the device under test. Both differential and single-ended input signals are supported by all probes. Input voltage swings small as 300 mV are supported in single-ended mode, and 150 mV for differential signals.
-
Product
Digital Controlled Phase Shifters To 4 GHz
-
Pulsar's Digital Controlled Phase shifters utilize PIN diodes and delay lines to produce the necessary phase requirements. These digital phase shifters use switched lines to obtain temperature stable phase shift. The phase is specified at the center frequency ± 3.0% and is proportional to frequency over the entire band.
-
Product
Sound Level Meter for Automotive – Car Noise Emission Inspection
HD2010MCTC
-
The level of noise produced by vehicles shall comply with standards prescribed by international regulations. During car inspections, horns and exhaust devices must be in good condition and comply with the requirements.
-
Product
Impedance Analyzer
6632
-
Frequency range: DC, 10Hz to 1/3/5/10/20/30MHz/50MHz. Basic accuracy up to ±0.08%. Automatic Level Control (ALC). Output impedance 25Ω/100Ω, switchable. Equivalent Circuit Analysis . Built-in DC Bias voltage ±12V. Ultra-high measuring speed < 3ms. Built-in the Dielectric constant-εr. Built-in the Permeability-μr. Support PC Link Software.
-
Product
Precision Impedance Analyzer
TH2851-130
-
Changzhou Tonghui Electronic Co., Ltd.
■ Test frequency: 10Hz-130MHz ■ High precision: using automatic balance bridge technology, four-terminal pair test configuration ■ High stability and consistency ■ High speed: the fastest test speed up to 5ms
-
Product
Total Nitrogen Analyzer
QuickTON
-
The QuickTONb from LAR AG provides rapid nitrogen analysis
-
Product
Flue Gas Analyzer
IMR 2800P
-
IMR Environmental Equipment, Inc.
The IMR 2800P is a portable, continuous measuring flue gas analysis instrument housed in an aluminum case.
-
Product
Handheld Wiring Analyzer
HT-128+
-
Reduce your wire harness assembly and installation difficulties now. The NEXU HT-128+ test platform provides a valuable tool for multi-point wiring continuity analysis. Our versatile, lightweight, handheld unit can serve your wiring test and maintenance needs from harness layout to product field support. The HT-128+ performs testing and troubleshooting, automated ring-out, directed assembly plus other features to resolve wiring issues quickly to achieve increased product availability!
-
Product
PXI Network Analyzers
M980xA Series
-
The Keysight M980xA Series of PXI network analyzers meets the most demanding challenges with a true multiport architecture that offers exceptional performance no matter how many ports you use. Gain deeper insights into your devices with the widest available portfolio of measurement applications for PXI VNAs, including spectrum analysis and noise figure measurements.
-
Product
PRECISION COMPONENT ANALYZER
6400 SERIES
-
The 6430B and 6440B Precision Component Analyzers provide thorough and accurate testing of any passive component to high resolution. In particular, for capacitor manufacturers, the instruments provide capabilities for both fast automatic production testing and complete design characterisation. Users include designers of passive components, manufacturing test, designing and testing materials as well as circuit designers who are evaluating component characteristics.
-
Product
Source Phase Control
S93088B
-
The S93088B allows users to set calibrated, arbitrary phase differences between two signal sources. The sources can be the analyzer’s internal sources or external signal generators routed through the analyzer’s test set. The phase difference can be fixed, or swept between two specified phase values. S93088B also controls the relative power level between the sources using the receiver-leveling feature.
-
Product
Cable and Antenna Analyzers
-
Handheld Cable and Antenna Analyzers offer measurement capabilities including precision return loss/VSWR, cable loss and distance-to-fault (DTF) measurements. Handheld analyzers help field technicians perform field verification and fault location to detect problems before they become costly, time-consuming system failures. Site Master is the leading choice for installation, maintenance, and troubleshooting of microwave cables and communication systems in cellular and broadcast industries as well as aerospace and defense.
-
Product
UHP Moisture Analyzer
5910
-
Using quartz crystal technology for speed, accuracy and calibration stability, the 5910 moisture analyzer is designed for ultra-high-purity (UHP) gas analysis in continuous monitoring and analytical cart applications. The 5910 is sensitive to changes in moisture concentration of less than 500 parts per trillion by volume (pptv), resulting in an accuracy of better than ±100 pptv, or ±10% of the reading.
-
Product
Vector Network Analyzer
R42XXE
-
The R42XXE Vector Network Analyzers are designed for measuring of S-parameters, VSWR and impedance of waveguide networks in the full frequency ranges of standard waveguides between 33 and 170 GHz. Frequency accuracy is ±0.2%. The measurement range of reflection factor modulus is from 0 to 1. The measurement range of reflection factor phase is from 0 to ±180° for 0.1< |Гx|<1 with accuracy ±7.5 o in 18-75 GHz frequency range and ±9.6° in 75-170 GHz frequency range. The measurement range of transmission factor phase is from 0 to ±180 o with accuracy ±(5+0.1 |Ax|) o for Ax >-50 dB in frequency range to 75 GHz, for Ax >-30 dB - to 170 GHz. Data can be displayed in the rectangular, Smith or polar diagrams. VNA requires Personal Computer with USB interface.
-
Product
1-phase Power Analyzers
-
PeakTech Prüf- und Messtechnik GmbH
Is a high-precision energy cost measuring device for recording the energy consumption of electrical devices and for calculating the current consumption of a device by entering the electricity price. Thanks to the integrated power factor calculation, all modern consumers such as Switching power supplies, TV sets, fluorescent lamps, LED systems and of course ohmic loads such as Electric heaters and hobs can be measured accurately. In addition, the high resolution, the low response characteristic and even very small or stand-by consumers from approx. 1 W can be measured.
-
Product
UHP Moisture Analyzer
5920
-
The 5920 is an easy-to-use process moisture analyzer offering a wide range of performance features for
-
Product
Silica Analyzer
SLIA-5000
-
Management of silica (SiO2) is paramount in preventing the formation of scales. This is because scales present in turbines will reduce the efficiency of power generation, especially for thermal power plants and nuclear power plants. By combining HORIBA's many years of track records and technological know-how, the silica analyzer has been reborn with conventional stability, reliability and maintainability.
-
Product
TOC Analyzer
QuickTOCultra
-
Fast, Accurate, Low-maintenance Monitoring of TOC, COD, TOD or Nitrogen
-
Product
Datacom Analyzers
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber provide E1/2M Transmission Analyzer is one multi-functional and full- featured digital transmission system test device, designed for the installation test, engineering check and acceptance, daily maintenance of digital networks, mainly performing channel test, alarm analysis, fault finding and signal analysis. In addition, this instrument further provides various protocol converters with one-way and bi-directional bit error test function. These capabilities make it ideal for field use.
-
Product
Stereoscopic Analyzer
Cel-Scope-3D
-
Can provide stereoscopic 3D monitoring and depth budget analysis at low cost. This allows accurate and comprehensive assessment and QC in a post-production environment. Alternatively it can also be used camera and rig set-up to be done quickly and confidently so that the 3D will be right first time. The Cel-Scope3D can be relied on to ensure your 3D to be pixel perfect and that the depth budget is used to its full advantage without abusing the audience.
-
Product
Low Noise Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM low noise amplifier MMICs cover a frequencies from DC to 86 GHz operation for a wide range of applications, including network infrastructure, radar and communication systems. MACOMs portfolio of low noise amplifiers offer a broad array of noise figures, input IP3, and input power in bare die and a variety of package types. Offerings include wideband distributed topologies and self or actively biased configurations tailored to system design needs.
-
Product
CO & NOX Analyzer
714
-
Combustion Efficiency Analyzer. NO & NOX Analyzer. CO Analyzer(calculatesCO2). Differential Thermometer. Differential Digital Manometer
-
Product
Hydrogen Storage Analyzer
IMI-HTP
-
The IMI-HTP is designed to characterize hydrogen storage materials using Sieverts method up to pressures of 200 bar. High accuracy is ensured by a minimized dead volume, all-metal construction, high thermal stability and accurate pressure measurement. Every IMI-HTP is specified to meet the challenging demands of high pressure H2 operation, with permanent overpressure protection to satisfy the most rigorous safety requirements.
-
Product
Powerline Analyzer
SHARK 100
-
Amperis introduces one of the highest performance panel-type billing grade meters in the industry. Based on a new platform, this low cost meter significantly outperforms other much more expensive equipment. This unit is perfect for new measurement applications and for direct and simple replacement of existing analog meters. The Shark is excellent for high accuracy energy measurement exceeding ANSI C12.20 (0.2%) and IEC 687 (0.2%) energy measurement standards.
-
Product
Electrosurgical Analyzer
HF-400
-
HF-surgery tester for functional testing of HF surgical devices according to IEC 60601-2-2.
-
Product
Spindle Analyzer
-
Hand-held, light-weight, wireless tactile probe with easy-hold grip stylus allows for inspection of intricate features & cavities for large, complex parts.
-
Product
Other Material Analyzers
-
GAOTek portable material analyzers deliver instant, relevant data for quick decision making in critical situations. Combining advanced technologies with an incredibly easy-to-use interface, our portable analyzers provide rapid, reliable chemical identification and material verification to increase throughput, increase quality and reduce risk. It can be used in any location, field environment or weather condition.
-
Product
PreEqualization Analyzer
-
Quickly locate upstream impairments. See micro-reflections and group delay. Find issues like microfractures, reverse splitters, corroded connectors and bad wiring. Display modems being impacted by a common impairment. Save time and money. Reduce truck rolls. Lower maintenance costs. Increase operational efficiency.Improve customer satisfaction Benefit from pre-equalization without masking problems Find and fix problems before they impact customers
-
Product
Image Analyzers
Morphologi Range
-
Morphological imaging is fast becoming an essential technology in the laboratory toolkit for particle characterization. The Morphologi 4 is a fully automated static image analysis system which provides a complete detailed description of the morphological properties of particulate materials. The Morphologi 4-ID combines the same automated static image analysis with Raman spectroscopy in a single, integrated platform, providing component-specific morphological descriptions of chemical species within a blend.
