-
product
100BASE-T1 Automotive Ethernet Protocol Analyzer
100BASE-T1
Prodigy Technovations Pvt. Ltd.
100BASE-T1 Automotive Ethernet Protocol Analyzer is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. Automotive Ethernet interface scales up to address current and future needs of in-vehicle bus speed requirement. Need for higher-speed in-vehicle bus is increasing to support feature-rich ADAS and connected vehicle needs. Two-wire full duplex 100BASE-T1 PAM 3 signaling is the choice of interface bus to address these needs
-
product
AL600 Is a Single Pair Ethernet (SPE) Switch Designed for Rugged Industrial Applications
EKF-AL600
The AL600 Single Pair Ethernet Switch, 7 x 100BASE-T1, 1 x 1000BASE-T Automotive Ethernet, Industrial, Ethernet, BroadR-Reach.
-
product
100BASE-T1 SFP Module
Art.-Nr.: TE-1430
Convert between 100BASE-T1 and Standard Ethernet The 100BASE-T1 SFP Module is the optimum solution to convert between 100BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 100 Mbit/s full-duplex 100BASE-T1.
-
product
IVN-8561, Automotive Ethernet Interface Device
786169-01
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
100BASE-T1 SPY 12 PORT
Art.-Nr.: TE-1500
Capture the traffic of 100BASE-T1, CAN/CANFD, LIN and Flexray Buses using only one device. The 100BASE-T1 SPY 12 port is a highly specialized test and evaluation tool for seamless capture of multiple in-vehicle-network technologies. It provides common timestamping of all incoming messages and delivers the traffic via Standard Gigabit Ethernet.
-
product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, which allows it to synchronize with an external network as well as the rest of a PXI system. The PXIe-8521 also provides LEDs on the front panel so that you can monitor the network link and activity.
-
product
Automotive Ethernet Interface Device
The Automotive Ethernet Interface Device converts unshielded twisted pair (UTP) Automotive Ethernet to standard Ethernet. This device is ideal for developing applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It includes ports for Automotive Ethernet connections and ports for 100BASE-TX Ethernet connections. You can use switches on the front panel to configure each 100BASE-T1 port as master or slave. The device also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
100BASE-T1 MEDIACONVERTER BCM
Art.-Nr.: TE-1000
The ideal physical layer conversion between Automotive Ethernet and your PC system. The 100BASE-T1 MediaConverter BCM establishes one direct point-to-point conversion between automotive ECU’s using 100BASE-T1 and any standard Fast Ethernet device with RJ-45 connector.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
100BASE-T1 MEDIACONVERTER NXP
Art.-Nr.: TE-1600
The ideal physical layer conversion between Automotive Ethernet and your PC system. The 100BASE-T1 MediaConverter NXP establishes one direct point-to-point conversion between automotive ECU’s using 100BASE-T1 and any standard Fast Ethernet device with RJ-45 connector.
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
Automotive Ethernet Compliance Solutions
These automotive Ethernet electrical test software packages let you automatically execute tests and display the results in a flexible report format. In addition to the measurement data, the report provides a margin analysis that shows how closely your device passed or failed each test. The automotive Ethernet electrical compliance solutions perform a complete set of electrical tests to meet the BroadR-Reach, 100Base-T1 and/or 1000Base-T1 specifications. The following solutions are available:
-
product
100base-T1 Ethernet (BroadR-Reach®) Logging Expansion With Low Latency
PT-15B
The PT-15B expands the PM-200 data logger from the Power Family by adding twelve 100base-T1 interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 100base-T1 packets are time stamped, filtered and sent to the PM-200 data logger via a 1000base-T interface.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
The 42-205-008 (PXIe) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
