-
Product
Shaft Speed Switches
-
A speed switch senses rotating shaft speed, comparing it to one or more settable over/under/zero speed alarm trip-points. A shaft speed sensor detects magnets embedded in a shaft-mounted pulser wrap/disc. As the shaft rotates, the passing magnets are detected across an air-gap as pulses with frequency proportional to shaft RPM. When a conveyor belt or bucket elevator begins to slip the pulse frequency (shaft RPM) crosses to the alarm side of a trip-point threshold, a corresponding relay de-energizes, providing shutdown or alarm.
-
Product
Rotating Dual Shaft Torque Sensors
RST SERIES
-
The RST- Series is our low range rotating torque sensors that are available in eleven full scale ranges of 10 through 30K inch pounds. The sensing element incorporates bonded foil strain gages of the highest quality along with coined silver slip ring and silver brushes for data transmission. The WR2, Flexural Natural Frequency, and Torsional Stiffness values as stated in the Dynamic Characteristics box below, are approximate and the tabulated data pertains to the torque pickup only, and does not include the effects of couplings or other rotating masses that would be part of a dynamic system.
-
Product
Shaft Power Measurement Kits
-
Shaft Power Measurement Kits are available in two formats, the standard and the compact kit. The compact kit is ideal for single day trials, while the standard one is used for long duration trials of between 30-60 days.
-
Product
Incremental > EX-Proof Encoders - Hollow Shaft
-
Incremental > EX-Proof Encoders - Hollow Shaft
-
Product
Slide Gate & Shaft Position
-
All six Shaft Angle Position Feedback Monitors in the SG1000 Series utilize absolute rotary encoders to provide independent and accurate feedback of a slide gate's or a valve's position to an external device such as a PLC or optional PM500 Process Meter Display Unit. Models are housed in a rugged, Explosion-Proof/Dust-Ignition Proof cast aluminum enclosure that is dirt, dust, grease-proof, and water resistant. In the case of a power failure, all SG1000s are designed to retain accurate gate position.
-
Product
Half Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi’s Half Shaft Telemetry System transmits torque signals from rotating shafts to a stationary telemetry receiver. It connects directly to strain gages adhered to the shaft converting it into a torque sensor allowing it to transmit shaft torque while the vehicle is operating. This system is a testing tool used by automotive and racing engineers to obtain real-time torque measurements from vehicle drivelines.
-
Product
Laser Shaft Allignment Tools
-
PRÜFTECHNIK Condition Monitoring GmbH
A laser alignment system is the most efficient way to align rotating machinery shafts. Using an adaptive alignment system instead of conventional alignment tools saves you time and money, increases machine availability, prolongs service life and maintenance intervals, and lowers power consumption. Alignment tools from PRUFTECHNIK adapt to virtually any asset, situation, or user skill level.
-
-
Product
Shaft Speed Pulse Generators and Shaft Speed Targets
-
Shaft Speed Targets are needed to generate a pulse for a Speed Sensor that is monitoring a shaft for RPM (Revolution Per Minute). Electro-Sensors Pulse Generators provide the shaft speed target needed for shaft speed detection with a sensor or switch. We have many options available for all your application needs including customizable split collar pulser wraps.
-
-
Product
Shaft Alignment
AT-200
-
Connectivity, mobile devices, cloud-based platform, apps are integrated in the AT-200 making it a tool for short response time between machine failures and corrective actions. The smart sensors use CCD technology for a superior measurement performance and precision alignment.
-
Product
Incremental > Heavy Duty Encoders - Hollow Shaft
-
Incremental > Heavy Duty Encoders - Hollow Shaft
-
Product
Shaft Alignment
NXA Pro
-
30 years of innovation continue with the introduction of the NXA Pro.
-
Product
High-Capacity Cylindrical Shaft Gage
1200-HC
-
For higher capacity requirements, the 1200-HC delivers exceptional accuracy and repeatability, powered by the same trusted laser interferometer technology as the 1200-LX but with a 52-86% larger swing diameter. With five models available to suit various shaft lengths and weights, the 1200-HC can accommodate shafts up to 4,572 mm (180 inches) in length and weighing up to 1,814 kg (4,000 lbs). Refer to the specifications for detailed model information.
-
Product
Incremental > Standard Encoders - Hollow Shaft
-
Incremental > Standard Encoders - Hollow Shaft
-
Product
Shaft Power Measurement Solutions
-
Our marine shaft power meter systems measure shaft torque, power, propulsion, rpm and thrust (if required), to ensure optimum performance is maintained throughout the lifecycle of a vessel. Using highly accurate & reliable strain gauge technology, combined with cutting-edge electronics, our system has an accuracy of 0.1%. It can be installed and commissioned within 1-2 days on a variety of shafts including intermediate shafts, thrusters, propellers and controllable pitch propellers. Our technology, along with our expertise in dynamic sampling of strain gauges, enable us to unlock a significant amount of information regarding the performance of the engine & propulsion shaft, along with the propeller.
-
Product
Rotary Shaft to Shaft Torque Sensor
-
Futek Advanced Sensor Technology, Inc.
The Rotary Shaft to Shaft Torque Sensor category has Torque Sensors which are used in slip ring and non contact rotary torque measurements. The most common utilization for these models is for inline/reaction applications, where measurements can be made in both clockwise and counterclockwise directions. The Rotary Shaft to Shaft Torque Sensors are CE certified and utilize a bonded metal foil strain gauge. As with most FUTEK products, we will gladly work with you to customize or modify our Torque Sensors to meet your precise needs.
-
Product
EEXI Shaft Power System (SHaPoLi)
-
Datum Electronics Ltd has developed a shaft power limitation (SHaPoLi) EEXI Shaft Power System, providing the necessary features and functionality to comply with the MARPOL Annex VI, MEPC.335(76) EEXI regulations.Our system uses a Shaft Power Acquisition Module to constantly display, monitor and record propulsion shaft power to ensure compliance with the EEDI requirements relating to CO2 emissions for ships over 400 gross tonnage.
-
Product
Radius, Straight Shaft Bullet Nose, Standard 0.61 (17.00) - 2.80 (79.00) General Purpose Probe
HPA-0J
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
-
Product
Marine Shaft Power Meter Systems
-
Datum’s Marine Shaft Power Meter Systems are developed to provide real time and ongoing power monitoring data on propulsion shafts, thrusters and diesel generators. These devices are commonly used for fuel economy monitoring and equipment maintenance planning programs and can be used in conjunction with our EEXI | ShaPoLi solution to keep vessel owners in line with the latest legislation.
-
Product
Electrostatic Capacitance-Type Gap Detectors
VE series
-
VE series are non-contact type of vibration/small displacement detector with high accuracy which can measure the distance between conductor such as metal and sensor’s surface in micron/submicron resolution. It demonstrates its best performance when used for the measurement and control of the axial and surface vibration of rotational shafts such as main shaft of turbines, electric motors, compressors, and of the thickness and width of moving objects. In addition to the measurement of the amount of displacement, a gap detector can also be used for a wide range of other measurement and control applications such as the measurement of the amount of slack or warping. The non-contact measurement process enables to apply no load to rotational or vibration body, and does not affect the material under measurement.
-
Product
Side Channel
-
Flowserve side channel pumps comply with ISO standards. They cover bare shaft, compact and inline designs. They fully satisfy the high operational safety standards of the process industry. Their self-priming and gas-handling characteristics guarantee safe operation, even in case of evaporation.
-
Product
Tachometers
-
Is an instrument measuring the rotation speed of a shaft or disk, as in a motor or other machine. The device usually displays the revolutions per minute (RPM) on a calibrated analogue dial, but digital displays are increasingly common.
-
Product
Rotating Telemetry Systems
2100B Series
-
Advanced Telemetrics International
Are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
Product
3 Channels, 0.5 VA @ 28 Vrms
DSK
-
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
SpeedMaster
-
The SpeedMaster™ is the only device that accurately tests the calibration of a speed switch, and allows testing of the alarm and shutdown features of the sensor while installed on the machine shaft.
-
Product
Real Car Transient Test System
RealCar Simulation Bench
-
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
Product
Explosion-Proof Differential Pressure Switch
H3
-
Explosion-proof, heavy duty, industrial unit has patented and unique new design which provides sensitivity to differential pressures as low as 10 inches of water (254 mm w.c.), yet handles total pressure of 1500 psi (103 bar). Unlike common differential pressure switches that use a piston-type motion transfer, the Series H3 utilizes a rotary motion transfer shaft that prevents a change in total pressure from causing a setpoint shift.
-
Product
General Purpose Probe
HT-1
-
HT-1 ''Workhorse'' General Purpose Probe - designed for temperature measurement of liquids, gases and semi-solids. Plastic handle with straight 3'' stainless shaft. Not good for surface temperatures. Maximum temperature 400°C, Time constant 0.5 Seconds. 5 foot lead. Not isolated.
