Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
Adapter
EXC-1553UNET/Px(S)
-
The EXC-1553UNET/Px is an intelligent, single - or - dual channel, MIL-STD-1553 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.The EXC-1553UNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Electronic Load Board 3U CPCI-S (air cooled)
056-377
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
PCB S.I/P.I (Signal Integrity/ Power Integrity)
-
Why need for PCB Simulators?Higher data speed (>GHz) Higher density Larger system size EMI concern Cost cut down Reduce of project term
-
Product
Counters & Generators
-
Are used in various industries to create signals that simulate behavior of system. Counters are instruments for measuring frequency.
-
Product
Line Monitor
LE-170SA
-
LE-170SA is a compact hand-held size line monitor for CAN/LIN. It has a touch screen and can be control as for smartfones. It has 1 CAN channel and 1 LIN channel and it can monitor both CAN and LIN communication thus monitoring of the network which has both CAN and LIN is available. The monitor function can diplay the communication data in real-time while saving it. The simulation function can send/receive the test data instead of the original communication partner. The ID filtering and trigger function make your development/evaluation more efficient. It also can measure 4 external signals as degital signals or analog signals while monitoring the communication data.It is light (300g) and convenient for field testing. The line monitor is useful for not only development but also maintenance.
-
Product
Steady-state Solar Simulator For PV Modules
SORAS LS
-
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
Product
AFDX®/ARINC664P7 Modules
-
AIM’s AFDX®/ARINC664P7 test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. Versions are available to support the Boeing specific ARINC664P7 extensions.
-
Product
Thermocouple Calibrators
-
Practical Instrument Electronics, Inc.
PIE has a thermocouple calibrator to fit your needs from the PIE 520B single type thermocouple simulator to the advanced troubleshooting capabilities of the PIE 422Plus. Have you had issues in the past where your thermocouple calibrator wouldn’t work with some of the instruments in your plant? Our thermocouple calibrators are guaranteed to be compatible with all process thermocouple inputs including all brands of smart temperature transmitters, PLC input cards, DCS systems and multichannel recorders.
-
Product
Encapsulation and Molding
-
The underlying science of adhesion and immersion has been extensively studied, simulated, and tested at Teledyne Impulse-PDM's laboratory in Alton, UK. With more than 25 years' experience in subsea engineering, Impulse-PDM offers high quality design and development services for all connectivity requirements.
-
Product
Low Power Programmable AC Power Source With Transients
-
Chroma Systems Solutions, Inc.
Equipped with a host of powerful features: power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, waveshape synthesis and regulation test software
-
Product
Battery Capacity Tester
BLU-T Series
-
Battery load bank BLU-T is a powerful and lightweight solution designed for condition assessment of telecommunication and radio equipment backup supply. This instrument can perform the battery capacity test on battery strings such as Pb, Li-ion, Ni-Cd, and others. It tests battery strings with voltages in the range of 0,9 – 70,5 V DC. As a special feature, the BLU110T model enables capacity testing of single PB, Ni-based as well as Li cells (with current up to 100 A).The capacity test is conducted in an accurate, user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU-T battery load bank enables setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, the BLU-T units can be connected in parallel, or BXL-T additional load units can be linked.The instrument offers a high power-to-weight ratio. BLU-T series has models starting from 12,8 kg / 28.2 lbs and up to 19,2 kW of power.A user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Discharge parameters can be monitored in real-time during the capacity test. A 4,3-inch touch screen shows overall battery voltage, discharge current, discharge test time and capacity during the entire test. Also, the capacity tester is compatible with DV-B Win software. A user can view a detailed numerical and graphical presentation of key parameters, and create reports in various formats.Testing can be carried out without disconnecting the battery from the service.
-
Product
Circuit Simulation Software
SIMetrix/SIMPLIS
-
SIMetrix/SIMPLIS is an advanced simulation tool optimized for efficient design of power electronics circuits. SIMetrix/SIMPLIS combines accuracy and convergence in a unique and powerful design environment, enabling 10-50x faster simulation for power supply designs. SIMetrix is a mixed-mode circuit simulation package designed for professional electronics engineers. SIMetrix comprises a substantially enhanced SPICE simulator, schematic editor and waveform viewer in a unified environment.
-
Product
2nd Generation PCIe Multi-function Decommutator
LS-50-E
-
The Lumistar LS-50-E PCIe Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCIe card slot. The multi-function decom and simulator is implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profiledaughterboard. CVSD voice decoding, h.261 videodecoding, and IRIG Chapter 8 decoding are achievedthrough software.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
42-203-002
Fault Insertion Unit
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
Engine Speed Control and Measurement (Test Set A)
MS 1100
-
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
Product
USB 2.0 SmartCable™ For ARINC429Test And Simulation
ASC429-x
-
USB 2.0 SmartCable™ for ARINC429 Test and Simulation with 6 channels (2Tx/4Rx) and 12 channels (4Tx/8Rx).
-
Product
Benchtop Test Chambers
MicroClimate
-
The MicroClimate 1.2 cubic foot benchtop test chamber is capable of simulating a full range of temperature and humidity conditions. This environmental testing chamber is designed to provide users with a compact unit for testing small components and products.
-
Product
Motion Control Solutions
-
DDC offers a complete line of Synchro/Resolver instrument-grade cards and test equipment including angle position indication and simulation, plus a variety of hardware and software to meet today’s civil, military, and COTS/MOTS requirements. DDC is a leading supplier of Synchro/Resolver-to-Digital and Digital-to-Synchro/Resolver components—the smallest, most accurate synchro/resolver-to-digital and digital-to-synchro/resolver converters available today. Most of these single chip and hybrid converters are based on ASIC designs, yielding the most reliable and affordable converters ever offered, and are the building blocks for DDC’s card-level products.
-
Product
Fast Transient Burst Simulators
FNS Series
-
A simulator to reproduce fast repetitive high frequency pulses which are generated when switching ON/OFF electric current on the inductive load. International Standard IEC 61000-4-4 defines immunity tests for power supply lines or I/O signal lines against fast transient repetitive bursts. Also adopted as a Japan Industrial Standard.
-
Product
PXI Precision Resistor Module 3-Channel, 3 to 11.4M
40-297-153
Programmable Resistor Module
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Precision Resistor Card 3-Channel, 3Ω To 22.3MΩ
50-297-154
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 239Ω
50-298-013
Programmable Resistor Module
The 50-298-013 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 239Ω with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Sand Dust Climatic Environmental Simulation Test Chamber
CX-SC80
-
Shenzhen Chuangxin Instruments Co., Ltd.
Sand Dust Climatic Environmental Simulation Test Chamber
-
Product
Air-arm-type Drop
KD-128A
-
King Design Industrial Co., Ltd.
All new developing products must undergo several strict testing processes while in designing, manufacturing and packing/ shipping even. Our drop tester will provide data digitizing and analyzing of your drop and striking while the products in transportation. The testing data will help you improve the packing and buffer materials.Packaged drop test is applied to test the anti-vibration & covering capability of packaging material and the sufficiency of product’s impact-resisting capability regarding packaged products. And use the test result to determine how to improve the packaging design. Free drop test is used to assess the characteristics of product’s free fall from improper actions; and evaluate the required strength and toughness of product under safety conditions.Repeated free fall test is to simulate object’s condition after normal fall to hard surface.
-
Product
Lansmont Testing Solutions
-
Lansmont develops state-of-the-art package testing equipment and instruments that enable engineers to evaluate, simulate and optimize product durability and packaging design.
-
Product
PXI Precision Resistor Module 3-Channel, 3 to 5.82M
40-297-152
Programmable Resistor Module
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
LTE eNodeB Testing
-
The DuoSIM and DuoSIM-Advanced are the most scalable eNodeB test systems in the industry. From basic functional testing to complex C-RAN environment simulation, the DuoSIM line of testers makes validation and development of network equipment faster, easier, and more cost effective.
-
Product
Simulation Software and Test Solutions
Simcenter Software
-
Siemens Digital Industries Software
The Simcenter portfolio uniquely combines 1D simulation, 3D CAE and test to help you predict performance across all critical attributes earlier and throughout the entire product lifecycle. By combining physics-based simulations with insights gained from data analytics, Simcenter helps you optimize design and deliver innovations faster and with greater confidence.
