Vector Signal Analyzers
Is like a spectrum analyzer with the addition of demodulation functions.
See Also: Vector Signal Transceivers
-
product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
E1/Datacom Transmission Analyzer
DTA-BERT
DTA-BERT E1/Datacom Transmission Analyzer can perform E1 transmission performance test (BERT) and status monitoring on data link (V.35, V.24/RS232, RS449, RS530, X.21). Model T can also perform G.703-64K bit error test, PCM31/30 test and Jitter test. Featuring comprehensive functions, easy operation and compact design, DTA-BERT provides total solutions for E1 line analysis and maintenance.
-
product
Frequency and Phase Agile 120 MHz Signal Generator.
DDS8p
The DDS8p generates cosine, sine and ACMOS/TTL output signals. The frequency is programmable in 1µHz steps from 100Hz to 120MHz. The phase is 14-bit programmable. The DDS8p is controlled by a binary parallel interface that allows frequency and phase changes as fast as 600 nanoseconds. It is accurate to 1ppm and requires 5 VDC power.
-
product
Manometric Gas Sorption Analyzer
IMI-FLOW
The IMI-FLOW combines the manometric gas sorption capabilities of all IMI analyzers with flowing mode operation and integrated mass spectrometry. Manometric mode offers high accuracy isotherm determination to 200 bar, while the flowing mode provides complete control of pressure, composition and flow rate. Integrated mass spectrometry allows downstream gas analysis for TPD and advanced methods.
-
product
Circuit Breaker Analyzer
CBAnalyzer
Simple operation requiring minimal trainingVery portable - it's a laptop or tablet pc running our Windows software programNo modification of the circuit breaker is requiredNo electrical connections are requiredRemoval of the circuit breaker from its mounting or cubicle is not requiredTesting can be performed during routine switchingData is easily transmitted over the internet to the users account where it is analyzed and compared with a known good profile (KGP) for that type of circuit breaker to determine: • Overall mechanical condition • Confirm maintenance intervals and lubrication • First trip testing data for arc flash compliance • Arc flash study validation checksPerform detailed analysis and store maintenance records using CBAnalyzer suite softwareAccess to the CBAnalyzer Account Manager which: • is where user accounts are created and each user's role is designated • provides access to your equipment database and test data archives • is where tests are synced • is where your equipment data is entered and stored • is required to use the CBAnalyzer software program
-
product
Light Industrial Grade MagStripe Analyzer
Mag3x Mini
Tests wide range of cards:Encoded ID1 Plastic CardsISO tracks 1, 2 and 3Embossed / Pre EmbossedEnglish and Chinese language software availableWindows 7 BasedSimple graphical displays show pass or fail for each cardSave detailed data on each card for future analysis12-bit resolutionFast pass/fail tool for production lineConvenient, mini form factorEasy-to-use reportingServiceable by end userCalibrate at your own facilityOne click testingFast 100K samples/second
-
product
Impedance Analyzers
Sciospec stands for Electrical Impedance at its Best. Electrical Impedance Spectroscopy has been our core technology ever since. In the past years we have developed a scalable and flexible technology plaform that allows for precise, customizable, yet cost-effective lab-bench impedance analyzers. Choose between our three standard instruments, add some powerful options and enjoy an impedance analyzer that perfectly fits for your application.
-
product
Signal Generator, 20MHz, 1 Channel
33509B
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
product
Signal Conditioners
Process transmitters isolate, filter amplify, and convert sensor signals to 4-20mA current or 0-10V voltage signals for interfacing with controllers and other instrumentation. Select from 2-wire loop-powered 4-20mA transmitters, 3-wire DC-powered transmitters, or 4-wire AC/DC-powered transmitters. 3-wire and 4-wire models are available as 4-20mA transmitters or voltage transmitters. DIN-rail and field-mount version are available. Configuration is easy with Windows software, push-buttons, switches, or pots for span/zero settings depending on the series.
-
product
PXI Network Analyzers
M983xA Series
Keysight’s M983xA PXIe vector network analyzer (VNA) combines all your measurements into a single instrument, enabling multisite, multi-DUT, multiport system characterization with faster speeds and greater flexibility.
-
product
PXI-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
778572-14
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
XRF Lead Paint Spectrum Analyzer
LPA-1
The LPA-1 is a state-of-the-art Lead Paint Analyzer using X-Ray Florescence (XRF) and K-Shell technologies, providing readings in as little as 2-4 seconds. It is widely considered the fastest, most reliable lead inspection system today. Non-destructive testing for lead on painted surfaces. Fast, efficient and easy to use testing device. Completes readings in 2-4 seconds.
-
product
Signal Switch/Relay Actuator
1260-13
The Astronics 1260-13 offers general purpose signal switching and control of external devices. The module provides 40 channels of DPST switches.
-
product
Power & Energy Analyzer
PS3550
The PowerSight PS3550 Power Analyzer is a versatile, easy-to-use 3-phase power analyzer that is ideal for energy audits, load studies, harmonic analysis, and more. The PS3550 couples its small size with a wide range of operating modes and measurement accessories to help you get the measurements you need, both now and into the future.
-
product
PCAP Analyzer
PCAP Inspector allows for quick and seamless segmented steps to prepare a focused and comprehensive analysis within Wireshark. During your visual and statistical analysis, select, and export the desired segments of your PCAP data, immediately importing your data into Wireshark.
-
-
product
Online Sulfur Analyzer
SOLA iQ
The SOLA iQ On-line Sulfur Analyzer replaces expensive and time consuming laboratory sampling for measuring total sulfur in refinery products including gasoline, diesel, kerosene, and jet fuel as well as many process gas samples such as Natural Gas, NGL and SynGas. The SOLA iQ analyzer offers an online adaption of ASTM D5453, D6313, D6222 & ISO 20846.
-
product
Optical Spectrum Analyzer Module Specification
CA92001B
UCINSTRUMENTS CA92001B C band optical spectrum analyzer module is a spectral engine for Process Analytical Technology applications. The OSA module acts as a stand-alone spectral engine, imaging and measuring a wide range of vapors, liquids and solids through transmission and diffuse reflection in a rapid non-destructive process. Leveraging our proprietary Micro-Optic technology, UC INSTRUMENTS’ C band OSA module features the following characteristics: (1) compact; (2) light-weight; (3) low power consumption; and (4) wide wavelength coverage. These characteristics of UC INSTRUMENTS’ compact OSA engines are suitable for a variety of handheld, portable or bench-top OSA/spectrometer applications. Equipped with a state-of-the-art internal wavelength reference, the OSA module is capable of precisely measuring optical spectrum. Because it does not require an expensive InGaAs detector array, the compact OSA module is a cost-effective alternative to other grating-based OSA/spectrometer engines. The OSA communicates with a PC or an instrument motherboard via an USB interface. UCINSTRUMENTS’ OSA module platform can be installed or co-packaged into existing NIR OSA/spectrometers as a cost-efficient alternative to other scanning optical engines.
-
product
2-Port 18 GHz Analyzer
M5180
VNAs and ACMs are delivered with factory calibration certificates containing no data. The add-on option for ISO17025/Z540-1 Accredited, Traceable Calibration Certificate and Uncertainties is available and needs to be specified at time of order.
-
product
Loop powered Moisture Analyzer
PLMa
Multifunctional Multi-Purpose Cost Effective, easy-to-use dew point sensor, dew point probe
-
product
HEVC Video Analyzer
Zond 265
Zond 265 is the first-to-market tool for the visual in-depth analyzing of HEVC/H.265 video bitstreams. It is intended to help video developers and researchers in codec development, easily isolate and identify visual artifacts or problems with bitstream compliance, and see the encoding elements of video data.
-
product
Test Analyzer
ST2302
Shenzhen Star Instrument Co., Ltd.
The ST2302 three-phase energy meter field test analyzer reaches accuracy class 0.02. Its stable performance comes from the embedding technology and digital signal processing. It is Windows CE-based and provides 7 inches color LCD display.
-
product
Dial Torque Analyzer
MTS-Series
Dial Analyzer is designed for hand tools, like torque screwdrivers and torque wrenches. This tool is not suitable for power tools. Ideal for checking torque tools on production floor daily or weekly to ensure the tools aren't falling out of calibration, or can be used in cailbration lab. Using a quality torque tester makes a safer world through accuracy and precision. Measuring torque is essential for companies to ensure their product’s quality, safety and reliability isn’t compromised. The failure of a three-cent fastener that isn’t properly tightened can lead to catastrophic or latent failures.
-
product
I2C/SPI Exerciser and Protocol Analyzer
PGY-I2C/SPI-EX-PD
Prodigy Technovations Pvt. Ltd.
I2C Protocol Analyzer and SPI Protocol Analyzer (PGY-I2C/SPI-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-I2C/SPI-EX-PD is the leading instrument that enables the design and test engineers to test the respective I2C or SPI designs for its specifications by configuring the PGY-I2C/SPI-EX-PD as Master/Slave, generating I2C/SPI traffic and decoding the I2C/SPI protocol decode packets
-
product
Handheld spectrum analyzer/Signal analyzer
Recently, a lot of equipment have taken the high frequency or microwave technology according to the advancement and the spread of the telecommunication equipment. As a result, the handheld spectrum analyzer to analyze the signal by the frequency domain is necessaries now. The handheld spectrum analyzer is roughly classified into a heterodyne method and a Fourier transform method. The heterodyne method is also called the swept frequency method and makes it possible to measure up to tens of GHz though only for the steady signal. On the other hand, the Fourier transform method is also called the real time method and can handle an unsteady signal though the low measuring frequency range up to tens of MHz. As for our spectrum analyzer or signal analyzer, the MSA300/400 series adopts the swept frequency method, and the MSA500 series adopts both the swept frequency method and the Fourier transform method.
-
product
6GHz RF Signal Generator
TGR6000
0MHz to 6000MHz frequency range10Hz setability, ±1ppm frequency stabilityLocking to external frequency standard-110dBm to +7dBm amplitude, 0.1dB stepsFast stepping sweep with dwell times down to 10msList sweep of up to 1000 points of amplitude vs frequencyUser compensation tables for specific test set-upsStorage for 12 generator set-ups and 16 sweep listsCompact half-rack 2U casing uses minimum bench spaceFull remote control through RS232, USB, LAN and GPIBSignificantly lower cost than other 6GHz generators
-
product
"Signal Transporter"
LTX-5525
The LTX-5525 conveys sixteen independent channels of digital information over a fibre optic link ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled 100 million times per second, multiplexed and transmitted serially over an optical fiber at two gigabits per second. The receiver acquires this digital data and de-multiplexes it to 16 separate output ports.
-
product
Mini Cloud & Pour Point Analyzer
OptiMPP
The automated OptiMPP provides highly accurate cloud and pour point results using only 0.5 ml sample. Simply place the sample in a disposable vial into the 20 specimen sample changer and press the OK key. No special programming or expected point is required. Results are available in 20 minutes for a -30ºC pour point.
-
product
Surface Area and Porosity Analyzer
TriStar II Plus
Micromeritics' TriStar II Plus is a state-of-the-art instrument suited for use in both quality control and research environments. Intended for laboratories that require high throughput and the highest quality data, it contains all the capabilities of the TriStar II with additional hardware and software features.
-
product
Network Monitor & Analyzer
CommView
CommView is a powerful network monitor and analyzer designed for LAN administrators, security professionals, network programmers, home users…virtually anyone who wants a full picture of the traffic flowing through a PC or LAN segment. Includes a VoIP analyzer.
