Waterproof Test Chambers
-
Product
Display Driver Test System
T6391
-
High-resolution flat-panel displays (LCDs / OLEDs) are becoming increasingly integrated. It is common for today's display driver ICs (DDIs) to contain a multitude of logic/analog circuits to manage advanced operations including touch-sensor functions. At the same time, the rapidly growing applications of LCDs / OLEDs in mobile electronics are driving demand for DDI's with smaller sizes and greater capabilities. These factors present serious IC-testing challenges. ADVANTEST's T6391 system is designed to address these needs along with DDIs' increasing number of pins and faster interfaces.
-
Product
Waterproof Portable DissolvedOxygen Meter
CyberScan DO 300
-
Waterproof and Dustproof Housing - IP67 rated, ideal for rugged harsh conditions. Plus it floats! :: Automatically Compensates Salinity and Barometric Pressure after manual input for increased accuracy
-
Product
Sand and Dust Test Chambers
-
This product is applicable for the dust proof and resistant test of various auto components and parts including
-
Product
Thermal Shock Chambers
-
Specialized environmental test devices that rapidly move products between extreme hot and cold temperatures to simulate real-world stress.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
-
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Thermal Abuse Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Thermal abuse test chamber is suitable for standard IEC 62133-2017, UL 1642 and GB 31241-2014.
-
Product
Salt Spray/Fog Chambers
-
This product is applicable for salt mist corrosion test to various accessories and parts, electronic components, coating of metal material and industrial products.
-
Product
Aquatic Chamber
6800-18
-
The 6800-18 Aquatic Chamber is used to measure steady-state carbon assimilation and chlorophyll a fluorescence from algal suspensions, coral, macro algae, and sea grasses using the LI-6800 Portable Photosynthesis System, the preferred photosynthesis system for terrestrial plant research.
-
Product
Insect Rearing Chambers
-
Chamber uses thermoelectric assembly for heating and cooling. This type of cooling/heating system completely eliminates need for conventional refrigeration system and failures due to mechanical components such as compressors thereby drastically increasing the life expectancy of each chamber.
-
Product
Walk-In Test Chambers
-
Standard and custom walk-in test chambers deliver the temperature or humidity testing performance you need.
-
Product
Chamber Light
LED-CL
-
The Teledyne Bowtech LED-CL Chamber Light is extremely safe and reliable, due to its advanced technology and innovation.The light has 100,000 hour life and has been designed specifically for use within the Hyperbaric Diving environment, whether that is in Hyperbaric Chambers, TUP's, Diving Bells or even Wet Bells.
-
Product
3-Axis AGREE Chamber Vibration Test Chamber Elevator Mechanism
-
Guangdong Test EQ Equipment co., Ltd.
Widely used in aviation, aerospace, shipbuilding, defense, electrical engineering, electronics, automotive, motorcycle, telecommunications, and scientific research industries. Designed to assess the reliability of electrical/electronic products, instruments, and equipment during transportation, storage, and operation. This integrated system combines a temperature/humidity test chamber with vibration platforms to independently conduct temperature, humidity, vibration, and combined environmental tests.
-
Product
Environmental Test Chambers
-
Guangdong Bell Experiment Equipment Co.,Ltd
Environmental testing chambers are also known as climate or climatic test chambers. DGBELL environmental chamber suppliers involved in the environmental chamber manufacture since 2005, we specialize in the manufacturing of humidity chamber, temperature chambers walk in environmental chambers.
-
Product
Stability Chambers
PH Series
-
The Darwin Chambers PH Series Stability Chambers are designed for performance specifications exceeding FDA and ICH requirements. For GMP studies, ultrasonic humidification provides excellent humidity control and avoids hot spots during mapping. Thermoelectric cooling provides more stable temperature control than equivalent refrigeration systems. All PH series chambers incorporate inherent cooling redundancy, quiet operation, simple serviceability and excellent reliability.
-
Product
Temperature Chambers
F Series
-
The Bemco F Series of free-standing, mechanically cooled temperature chambers are offered in Wide Range, F Series (-73 C to 177 C or -100 F to +350 F) and Narrow Range (-35 C to + 177 C or -31 F to + 350 F). These chambers feature innovative Bemco conditioning systems designed to provide a precisely repeatable environment for testing in accordance with Military Standards (MIL-STD's), production testing, and laboratory testing.
-
Product
Waterproof Handheld Meter with pH electrode
CyberScan PCD 650
-
A Eutech Star Buy! Combining the strengths of all CyberScan 600 series meters, the CyberScan PCD650 is our top-of-the-line waterproof handheld that enables concurrent measurement of pH, conductivity, dissolved oxygen and temperature, all at the same time.
-
Product
Precision Humidity Chambers
ELH Series
-
The Edgetech Instruments Model ELH Series is a series of precision humidity chambers, with NIST traceable accuracies in humidity (±0.5% typical), temperature (±0.1°C) and dew point (±0.2°C). The ELH Series consist of a programmable controller for constant precision control and uniformity, and an integrated DewMaster chilled mirror hygrometer for accurate temperature and humidity measurements.
-
Product
Thermally Protected Ballast Heating Test Chamber
TPB-UL935
-
Working room dimension: 610×610×610mm• Temperature range: RT+10℃～+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)
-
Product
Anechoic Chamber Filters
-
RF leakage through Ethernet and USB cables can destroy even the best RF enclosures and chambers. The need for filtering in the ever congested RF environment requires special filters that can pass USB 2.0 and 10/100/1000 Mbps Ethernet signals and filter out unwanted higher frequencies such as cellular and WiFi. The Adaura Technologies USB/Gigabit Filters provide one GigE and one USB 2.0 pass-through connections while filtering out other RF up to 8GHz. It has a small form factor to allow easy installation. It is a most cost effective solution for a clean chamber set up. In a typical chamber, WiFi signals are reduced to <-100dBm with this filter installed.
-
Product
Precision Altitude & Climate Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
Primarily used in aviation, aerospace, shipbuilding, military equipment, electrical engineering, electronics, automotive, motorcycle, telecommunications, and scientific research industries to evaluate the reliability of electrical/electronic products, instruments, and other equipment during transportation, storage, and operation.
-
Product
ORPTestr® 5 Waterproof Pocket Tester
-
The pocket-sized OPR tester has a replaceable single-junction sensor which can be easily switched out, allowing you to save money by using the tester body over and over again. A large LCD makes viewing measurements easy and features a three-color backlight indicating operational mode—blue for measurement, green for calibration and red for alarm condition. It is ideal for checking dirty water, heavy metals, sulfides, and organic materials. Additional features include hold function to lock in measurements, self-diagnostic error message, and status icons for measurement stability and low battery voltage. The IP67-rated housing features an easy-to-grip design and floats if accidentally dropped in water when sensor cap is on. Powered by four AAA batteries, the testers can operate up to 400 hours continuously. To conserve power, the unit will auto power-off after 8 minutes of nonuse.
-
Product
Waterproof Meter with ATC Probe
CyberScan pH 600
-
Cal-Due Alarm Prevents Out-dated Calibrations, while Set-Point Alarms warns when readings are outside set-point limits.
-
Product
Waterproof Portable pH / Conductivity / TDS Meter
CyberScan PC 300
-
Waterproof and Dustproof Housing - IP67 rated, ideal for rugged harsh conditions. Plus it floats!
-
Product
6TL22 Off-Line Testing Platform
H71002200
-
Learn about our Build to print service for Test Platforms. The 6TL22 Platform is a perfect base for the conception of a real modular Automatic Test Equipment for low to mid manufacturing volumes.A system designed around the 6TL22 is simple, easy to maintain and cost effective. The rack is prepared for the direct integration of the three platform based receivers from Virginia Panel, the S6, G12 and G12X.
-
Product
TSA Thermal Shock Chambers
-
Traditional three-zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air is pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
Product
Humidity Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Humidity chambers offer a wide range of standard solutions for your testing program. Environmental testing with a humidity chamber helps improve product reliability and durability. Humidity chambers are available in a variety of styles, sizes, and performance configurations. All humidity chambers come with a standard temperature range for combined temperature and humidity testing.Humidity may affect the life expectancy of a component by creating stresses on the part materials and altering its electrical properties in a way that the component reliability is significantly diminished.Humidity tests are those performed with the aim of evaluating the properties of materials used in components and the reliability of non-hermetic packaged devices in humid environments.
-
Product
Insect Rearing Chamber - Benchtop
IRC3
-
This 3 cu.ft benchtop insect rearing chamber is used by scientists in many research areas, from genomics to clinical epidemiology and species conservation. This chamber can be used in many types of insect growing projects where researchers are constrained by laboratory space.
-
Product
Ozone Test Chambers
-
Labodam Ozone Test Chambers are designed to detect the concentration of ozone while requiring low maintenance, having well-built corrosion resistant bodies, and while utilizing noiseless generators.
-
Product
TTC-1 Tracking Test Chamber
TTC-1
-
It is according to IEC60695 and IEC60112 (GB4207), the Tracking Test Chamber TTC-1 is intended for determining the degree of protection against formation of conducting paths in solid insulating materials, due to the electric stress and electrolytic contamination of the surface. This method simulates tracking currents on insulation material by providing drops between electrodes. During the process of normal use, insulating material may be exposed to moisture and dirt, if conductive, may cause stress and fire hazard.
-
Product
Halt Hass Chambers
-
HALT and HASS chambers from WEIBER provide extreme temperature & vibration capabilities used during the product design and manufacturing cycles to compress the time normally required to identify design and process weaknesses. HALT techniques are important in uncovering many of the weak links inherent to the design and fabrication process of a new product. HASS techniques are incorporated during the production phase to find manufacturing process defects that could cause product failures in the field.
