Product

Probe Card

VC43™/VC43EAF™

-

Celadon

VC43™/VC43EAF™ - Celadon

VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliability testing. Cards can be configured up to 104 probes in either single or dual layer with near vertical probes to minimize scrub lengths on pads allowing the VC43s to probe pads as small as 30 microns.

Product

Extenders

-

Kramer Electronics Ltd.

Kramer Electronics Ltd.

Comprehensive line of innovative range extension solutions for sending various signal types over long distances using twisted pair, fiber, or coax cables.

Product

Multi-Network Cable Tester

3PK-NT007N

-

Prokit's Industries Co., Ltd.

3PK-NT007N - Prokit's Industries Co., Ltd.

Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.

Product

Terminal Mechanical Strength Test

-

Aero Nav Laboratories, Inc.

Aero Nav Laboratories, Inc.

The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.

Product

Copper Test Solution

DSX CableAnalyzer™ Series

-

Fluke Networks

DSX CableAnalyzer™ Series - Fluke Networks

The DSX CableAnalyzer Series copper test solution enables testing and certification of twisted pair cabling for up to 40 Gigabit Ethernet deployments and will handle any cabling system whether it is a Cat 5e, 6, 6A, 8 or Class FA and I/II. Certifying a cable is one part of a process that starts with system design and ends with system acceptance. The faster that process goes, the more profitable you'll be. Unfortunately, there are a lot of things that slow the process down setting up the tester incorrectly, testing to the wrong limits, waiting for skilled technicians to analyze and troubleshoot failures, misinterpretation of results, and producing test reports that customers cannot understand.

Product

72" Cable

RCONSCSI3-6

-

Abaco Systems Inc

RCONSCSI3-6 - Abaco Systems Inc

72” cable (with twisted pairs) transitions from the card front I/O connector on the RAR-USB, RAR-XMC, RAR-PCIE, RCEI-530, RCEI-830A, CEI-520/520A, R830RX, MAC2-VXI, RMAC-VME, P-DIS or P-SER to a SCSI-3 connector. This cable is for the RAR-PCIE, RCEI-530, and CEI-520/520A products, where the rear Discrete I/O connector utilizes the CONM50-D37 or other IDC-50 ribbon connector.

Product

Powerful Diagnostic Instrument

Flex-US

-

SDT Ultrasound Solutions

Flex-US - SDT Ultrasound Solutions

The design of the Flex.US is based on the popular "Flexible Sensor" from SDT. Mounted on the end of a flexible steel pipe, the ultrasound sensor can access any hard-to-reach location. Bend, twist and curve your Flex.US to suit your inspection. Safely scan electrical cabinets and behind machinery guards without putting your hands in danger. To ensure comfort, the volume control is quickly adjusted when very loud ultrasounds are encountered. This sensitivity provides a high level of precision making leak detection a pleasure, not a chore.

Product

Cable Certifiers

LANTEK III Series

-

Trend NETWORKS

LANTEK III Series - Trend NETWORKS

New permanent link adapter saves money. Send test data anywhere using IDEAL AnyWARE app. Certifies multimode and single-mode fibre (optional). Professional PDF reports with free software. Certifies twisted pair cabling to TIA/ISO standards. The LanTEK III is an easy to use cable certifier that meets existing TIA and ISO/IEC performance requirements for testing up to Cat 7A/1000MHz. FiberTEK III adapters are used with LanTEK III for fast and simple certification of high bandwidth single-mode and multimode fiber optic cabling including support for encircled flux testing.

Product

- RS-232 to RS-485 2 Wire with LCD Display

Model 366

-

Telebyte, Inc.

Model 366 - Telebyte, Inc.

FEATURES: DataSpy® Status Display; Implements Low Cost LAN; Supports 32 Users; Uses Single Twisted Pair; External DTE/DCE Switch; Programmable Contention; Selectable Termination. The Model 366 allows interfacing RS-232 based equipment with networks/equipment using RS-485.

Product

Test Research

TRI

-

HW Test

TRI - HW Test

REBOUNDER test kits feature two separate "Co-Active Seals", "Quick Twist" Locking Guide Pins, and boards constructed of fine weave G10/FR4, increasing testing reliability and accuracy while simplifying finishing, debugging, and maintenance. All H+W products are backed-up with our "Test-Assured" one year warranty, in writing, and SAME DAY SHIPMENTS