Cables
See Also: Cable Assemblies, Cable
-
product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m, HV
A009DM5-C-HA050
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
product
RF Hybrids
RF hybrids are used for combining multiple power line carrier (PLC) TX/RX units together onto one cable without causing interference between transmitters and receivers. They are also used for splitting PLC signals to go to two or three phases of a power line.
-
product
sbRIO-9208, Non-Enclosed, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
780979-01
Non-Enclosed, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The sbRIO‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The sbRIO‑9208 uses a standard D‑SUB connection for use with cables and connector blocks. Non-enclosed modules are designed for OEM applications.
-
product
Debug probe for ARM Cortex processors
USB Multilink ACP
P&E’s USB Multilink ACP is a debug probe which allows a PC/laptop access to JTAG/SWD on ARM Cortex devices from several manufacturers (see complete list below). It connects between a USB port on a Windows machine and the standard debug connector on the target. The product photos to the left of this page show how the headers can be accessed by simply flipping open the plastic case. Ribbon cables suitable for a variety of architectures are included. By using the USB Multilink ACP, the user can take advantage of the debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.
-
product
Analog DVR
Sylo Vision Technology Co., Limited
Security cameras capture an analog video signal and transfer that signal over coax cable to the Digital Video Recorder (DVR). Each camera may be powered by plugging in the power supply right at the camera or by using RG59 Siamese cable which bundles the video and the power cables. The DVR converts the analog signal to digital, compresses it, and then stores it on a hard drive for later retrieval. Intelligence is built into the DVR to handle such things as scheduling, motion detection, and digital zoom. Monitors for viewing the video are connected to the DVR, or it can be set up to publish over an internal network for viewing on PCs. The DVR can also be set up to broadcast over the Internet and can add password protection and other features. When broadcasting over the Internet, the video for all of the cameras is transmitted as one stream (one IP address). Therefore, it is very efficient.
-
product
8 Pin Power D-Type Female Connector, 40A, Without Backshell
92-960-008-F
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
product
DMX Line Tester
DMXTSTR
The DMX Line Tester instantly displays the presence of +/- data on DMX lines and feed-through connectors. It serves as a perfect pocket sized tool for troubleshooting DMX512 cabling.
-
product
TB-2634, Screw Terminal, Ribbon, 4x64, 1-Wire PXI Module Matrix Terminal Block
778840-01
Screw Terminal, Ribbon, 4x64, 1-Wire PXI Module Matrix Terminal Block - The TB-2634 provides the necessary routing to configure the PXI-2529 PXI Matrix Switch Module as a 1-wire 4×64 matrix. You can directly connect the TB-2634 to the front panel I/O connectors of the PXI-2529. The … TB-2634 includes ribbon cable headers that provide access to the rows and columns of the matrix.
-
-
product
DB25F-DB25M, Low Profile I/O Cable, 25-Pin Female DSUB to Male DSUB (1m)
154742-01
Low Profile I/O Cable, 25-Pin Female DSUB to Male DSUB (1m)
-
product
200-Pin LFH Connector Block, Female
B200LFR-2F-5B
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
product
Real-Time Ethernet Master/Slave Network
EtherCAT
EtherCAT is an open real-time Ethernet Master/Slave network developed by Beckhoff. Today, it is an open standard, managed by the EtherCAT technology group. EtherCAT sets new limits for real-time performance since it processes 1000 distributed I/O in 30 µs or 100 axis in 100 µs using twisted pair or fiber optic cable. Regarding topology, EtherCAT supports a simple low cost line structure, a tree structure, daisy chaining or drop lines - no expensive infrastructure components are required. Alternatively the classic more expensive switched star topology can be used.
-
product
75 Ohm Mini SMB to SMZ/Type 43 Adaptor Assembly
40-978-711-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
SparkFun XBee Explorer USB
This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programming pins on the XBee unit.
-
product
Dissolved Oxygen Meter with 3m Cable Electrode
DO 6+
User Customisation for user's flexibility like toggling of various modes from ppm, mg/l to % saturation, view electrode diagnosis, etc.
-
product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable, 2m
192061-02
68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable - The SH68M-68F-EPM Cable, sometimes referred to as SHC68-68-EPM, connects DAQ devices to accessories or cables with D-SUB connectors. You can use this cable to create custom cabling for your DAQ device. The SH68M-68F-EPM Cable is offered in different lengths.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 1m, Spring Latch
A068SMR-T-5B100
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
Cable Assembly, Receiver, TriPaddle, 36", 2 20-Pin Female Power Connectors
540054010201
Cable Assembly, Receiver, TriPaddle, 36", 2 20-Pin Female Power Connectors
-
product
50 Pin D-type Connectors & Cables
These standard voltage and high voltage 50 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends
A068SMR-T-5A100
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
Mini Optical Power Meter
TM537
TM537 Mini Optical Power Meter has compact structure and stable performance and ensures high measuring precision of 850nm, 1300nnm, 1310nm, 1490nm, 1550nm and 1625nm wavelengths. Used together with Optical Laser Source, it could accurately measure the loss of bier,cable and other passive optical devices.
-
product
Twinax, Contact, ITA, 50 Ohms
610113145
For increased reliability and to eliminate the need for polarization, the design of VPC’s Twinax contact consists of two concentric inner conductors for termination to the twisted pair, and an outer shield for termination of the cable shield.
-
product
High Definition Audio Daughter Board with Line-in, Line-out and Mic-in
DB-Audio2
- Realtek ALC262 High Definition Audio codec- Three jacks: line-in, line-out and mic-in- 5x2 pin header for cable connection to external audio header on SBC- 4-pin header interface for CD audio output
-
product
PXI 16x16 Matrix Module, 2-Pole, 2A, 60W
40-582-001
The 40-582 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 16x16 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 78 pin D-Type connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
product
Tip sensor
KELLER AG für Druckmesstechnik
Designed for measuring flow rate and ram pressure in pipework.The probe can be advanced a number of metres into tight canals thanks to dimensions ranging from ø 1,32 mm to ø 2,64 mm and a highly flexible cable.
-
product
Stand Alone Low Voltage Tester
TestMate 128
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
-
product
75 Ohm MCX to MCX Cable Assembly
40-977-761-0.5m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Network Test LanCaster Pro ST
The NEW Lancaster Pro-ST is a low-cost wire map tester which tests and certifies structured cabling continuity to a TIA568A/B, USOC and ISDN standards. The new Lancaster Pro-ST displays on screen wiring configurations showing the length of all 4 pairs and length of pair to fault up to 150m (500ft).
-
product
Coax, Contact, Receiver, 75 Ohm HD, sm59/U Belden 1855A, 3 GHz
610102133
Primary mating contact 610102132. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – BrassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 2.0 lbs max [0.91 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR ≤ 2.26 @ 3 GHzInsertion Loss -0.86 dB MaxDWV 1500 VDC min.Contact Resistance 5 mΩ center/ 3 mΩ outer Cable Specifications sm59/U Belden 1855AEnvironmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition EInsulation Resistance 1000 MΩ min.
-
product
Broad-Range High Voltage Non-Contact Tester
HVNCVT-2
Use to check for the presence of voltage in overhead conductors or to find faults in cables.7 sensitivity ranges up to 230kV AC (240V, 4.2kV, 15kV, 25kV, 35kV, 69kV, 115kV, 230kV).Audible and visual signals indicate the presence of voltage.Water resistant.Includes durable carrying case and universal/shotgun adapter.
