Analog Output Modules
-
Product
PXIe-4322, 16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module
782878-01
-
16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module—The PXIe‑4322 is a channel‑to‑channel isolated analog output module with integrated signal conditioning. The device provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters on the same device, the PXIe‑4322 isolated analog output module delivers a smaller footprint and higher measurement performance. In current mode, the module operates in all four quadrants, so you can both sink and source current. Isolation and higher voltage and current outputs make this module ideal for automotive applications.
-
Product
REM-11115, 4-Channel, 2-Wire Analog Output Module for Remote I/O
784749-01
-
4-Channel, 2-Wire Analog Output Module for Remote I/O - The REM‑11115 is an analog output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11115 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. You can use the REM‑11115 for voltage or current output, and it features a 2‑wire spring terminal connection method. The REM‑11115 has selectable output ranges and short-circuit-proof output channels.
-
Product
Modbus Analog Output Modules
DAT3020 Series
-
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
Product
4-Ch Analog Output Module
ADAM-5024
-
Accuracy: ±0.1% of FSR for current outputEffective resolution: 12-bitIsolation voltage: 3000 VDCOutput range: 0 ~ 20 mA, 4 ~ 20 mA, 0 ~10 VResolution: ±0.015% of FSRChannels: 4Output type: mA, V
-
Product
Analog I/O module with 8 differential analog output channels
IO108
-
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 8 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
Product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-02
-
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
Product
PXI-6711, 12-Bit, 4-Channel, 1 MS/s PXI Analog Output Module
777794-01
-
12-Bit, 4-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6711 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6711 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
I-87K Analog Data Acquisition Modules
-
ICP DAS offers a versatile array of serial based analog I/O modules to meet the precise needs of sensitive data acquisition applications using I/W-8000 controllers. ICP offers a bevy of thermistor, thermocouple, RTD, strain gauge, and universal I/O, as well as high resolution analog output modules!
-
Product
Analog Output Module, 16-bit D/A
IP231
-
The IP231 outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
-
Product
32 Channel PWM Generator Module with Analog Outputs
DP-VME-5835
-
DP- VME-5835 is a Pulse Width Modulator module with analog outputs. This module has thirty two Pulse Width Modulated output channels and four analog output channels.
-
Product
I/O Analog Module with 32 single-ended analog output channels
IO110 I/O
-
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 32 output channel has its dedicated D/A converter with an update time of 3µs. The output coupling of the module is single-ended for all channels. The output range of each channel can be selected individually.
-
Product
Multichannel Voltage Output D/A Converters
-
Analog Devices offers an industry-leading family of multichannel voltage output D/A converters (DACs), covering 8-bit to 16-bit resolutions, from 2-channel up to 40-channel density, and serial SPI or I2C interfaces. This family of precision D/A converters are in demand for applications that require high channel density and a small form factor, such as optical communications, analog output modules, or LED displays. ADI’s multichannel voltage output D/A converters provide features such as the availability of multiple independent output spans, system calibration functions that allow user-programmable offset and gain, or D/A converter increment/decrement functionality, which reduces the need to add external precision gain stages and facilitates the use of this family of D/A converters.
-
Product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-01
-
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
-
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
sbRIO-9269, Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781120-01
-
Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The sbRIO‑9269 is a channel‑to‑channel isolated analog output module. The sbRIO‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes. Non-enclosed modules are designed for OEM applications.
-
Product
Analog Output Module, 16-bit
IP235A
-
IP235A modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs. An internal RAM buffer enhances control over the transfer of data to the DAC.
-
Product
PXI-6713, 12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
777795-01
-
12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6713 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6713 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
Ruggedized Field Deployable Tester
PUMA
-
- 18-slot PXI / 4-slot SCXI Chassis- 1.2 GHz Embedded Controller- 4-axis Motion Controller/Simulation- 8-port RS-232 Serial Module- 4-port RS-485 Serial Module- 48 bit Isolated Digital I/O- Reconfigurable multi-function I/O FPGA Module- 5 1/2 digit DMM- 200 MHz 2-channel Scope/Digitizer- Multi-function Data Acquisition (DAQ)- 8-channel Analog Input Module- 6-channel Analog Output Module- General Purpose Switching- RF suite (optional)
-
Product
Isolated D/A Converter 8 Channel, 250kSa/s
OTP2 module no.187
-
The PXIe‑4322 is a channel-isolated analog output module with built-in signal conditioning. The module provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters in one device, the PXIe‑4322 isolated analog output module offers smaller dimensions and higher measurement performance. In current mode, the module operates in all four quadrants, allowing current to be drawn and sourced. Thanks to isolation and outputs for higher voltages and currents, the module is particularly suitable for applications in the automotive sector.
-
Product
Control Unit
MX 256
-
Teledyne Gas & Flame Detection
The MX 256 is a digital control unit intended for the detection and measurement of gases present in the atmosphere and more generally for the processing of any digital signal from digital sensors (OLCT 10N types), relay module, analog output module, logic input module. Thanks to its new option, an industrial controller module or remote HMI, it is possible to add analog input modules for sensor-transmitter connection (4-20 mA) and / or relay modules, this allows to not only extend the capacities but also to have event recordings (Location, Alarms,.....) and to have access to the data via the embedded web page.
-
Product
16 Channel Isolated Analog Output Module
DP-cPCI-2502
-
The DP-cPCI-2502 is a 16 channel analog output module organized in four groups of 4 channels each. Each group is isolated with respect to each other and with respect to the system using optical isolators and DC-DC converters. Each output channel is driven by a 16 bit resolution precision DAC. The input digital data is converted to analog signals of ±10V range. The digital data for the DACs is written from the cPCI interface via two banks of latches enabling a double buffered output scheme.
-
Product
Termination Boards
-
Termination Boards for DCS Distributed Control Systems. Available in a wide variety of analog, digital, RTD, and relay options. These boards are for analog input and output modules. It is a general termination board for most kind of analog modules. There are various sizes of boards for users to choose from.
-
Product
PXIe-6739 , 16-Bit, 64-Channel, 1 MS/s PXI Analog Output Module
783801-01
-
16-Bit, 64-Channel, 1 MS/s PXI Analog Output Module—The PXIe‑6739 is a high-density analog output module. The device is ideal for applications such as stimulus-response tests and open-loop simulations at high densities. You can achieve the maximum sample rate if using up to 16 channels, where each channel is on a separate bank. The PXIe‑6739 also includes 20 digital I/O lines, four counter/timers, digital triggering, and advanced timing to meet a wide range of application requirements. Its digital triggering and PXI Express synchronization capabilities allow it to be coupled with additional data acquisition, motion, and vision products to create highly custom measurement solutions to test innovative designs.
-
Product
PXI-6722, 13-Bit, 8-Channel, 800 kS/s PXI Analog Output Module
778999-01
-
13-Bit, 8-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6722 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6722 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
NI-9263, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module
779012-01
-
100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module - The NI‑9263 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST‑traceable calibration. The NI‑9263 module includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
Analog Output Module
ND-6021
-
- Voltage Output: 0 to 10 V- Current Output: 0 to 20 mA, 4 to 20 mA- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.1% of FSR (current); ± 0.2% of FSR (voltage)
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2502
-
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
Product
NI-9262, 1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module
785503-02
-
1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module - The NI-9262 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. The NI-9262 module includes a channel-to-earth ground isolation barrier for safety and noise immunity.
-
Product
I-8000 Analog Data Acquisition Modules
-
ICP DAS offers a versatile array of analog, cartridge based I/O modules to meet the precise needs of sensitive data acquisition applications using I/W-8000 controllers. ICP offers a bevy of thermistor, thermocouple, RTD, strain gauge, and universal I/O, as well as high resolution analog output modules! Please note that more modules are available in the "serial 87k section".
-
Product
sbRIO-9263 , Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module
780876-01
-
Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module - The sbRIO‑9263 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST‑traceable calibration. The sbRIO‑9263 module includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity. Non-enclosed modules are designed for OEM applications.
