Frequency Converters
-
Product
Frequency Counters
-
Combines a calibrated RMS RF Power Meter, a wide-band frequency counter, and a RF Signal Generator into one miniature USB device. Incredibly useful in production verification environments and other automated test setups.
-
Product
Frequency Synthesizers
-
7 different types of synthesizers for a broad range of applicationsBroad bandwidth, fast setting, and low phase noiseLow-cost custom designs available
-
Product
Frequency Multipliers
-
Analog Devices active and passive frequency multipliers enable designers to economically multiply lower frequencies to higher frequencies without creating measurable additive phase noise. This broad portfolio features a range of devices that can meet the size, volume, and cost needs for multiple applications, including:
-
Product
Protocol Converters
-
Applied Systems Engineering, Inc
ASE provides a total solution approach to the area of protocol test equipment with its’ family of PC based protocol test products. The ASE2000 RTU Test Set is a full-featured protocol test unit that provides the user with a powerful and flexible tool for testing and maintaining SCADA RTU and SCADA IED equipment and diagnosing communication problems.
-
Product
Charge Converter
CH-6130/6140
-
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
Product
Three-Phase Converters
SIRIO 3PH 7 ALFA 3PHSAP
-
The three-phase converter is an electronic equipment able to vary the RMS value of a sinusoidal voltage by controlling no. 6 controlled, antiparallel-connected conducting diode pairs.Since the wave form is symmetrically split both into positive and negative halfwave, the output voltage average value is not affected and equal to zero. This means that three-phase loads can be fed without gene rating inside the mesh a circulating current with average value other than zero.Moreover, the three-phase converting is obtained with only one control circuit thus ensuring balance between the three linked voltages applied to the load.
-
Product
Interface Converter
ZET 7076
-
Previously it was widely thought that it is enough to receive sensor readings and to have remote control over them. But gradually there evolved a need for remote control, i.e. people need to receive sensors readings and to control their performance via Internet (for instance, on a portable device). Such possibility simplifies quite a lot of tasks since one can control performance of a system located at the other end of the city or even a country.
-
Product
Frequency Multipliers
-
A nonlinear electronic circuit that takes an input signal and generates an output signal at an integer multiple (like 2x, 4x, 8x) of the input frequency.
-
Product
50-Watt DC/DC Converter; Single Output
55JS1
-
NAI’s 55JS1 provides full-power, single output at a baseplate temperature of +100° C.
-
Product
Protocol Converter
MACC
-
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
Product
Power Frequency Transducer
PP1S
-
1. Measuring and conversion IEC 6882. Dielectrical strength IEC 688 4 KVac / 1 min.3. Impulse test ANSI C37.90 / 1989 IEC 255-3 5KV ( 1.2 x 50 us ) 3KA ( 8 x 20 us ) - current coil4. Surge test (ring wave) ANSI C37.90 / 1989 ( 3KV - 0.5us / 100KHz ) IEC 255-3 ( 2.5KV - 0.25ms / 1MHz )5. Adaptability for power system VDE 0110 6. Measuring reliability VDE 3540
-
Product
600-Watt DC/DC Converter, 6U VME/cPCI
55U91-01
-
NAI’s 55U91-01 is a 600 Watt DC/DC Converter that plugs directly into two card slots in a standard 6U VME chassis. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts +28 VDC input, provides up to 9 outputs at up to 614 Watts, and addresses the power supply needs of both VME and cPCI systems.
-
Product
Frequency Divider
Trig-TekTM 313A
-
Divide high frequency to a lower frequency with an exact integer division with 1-digit divisor increments from 1 to 9999
-
Product
Frequency Doublers
-
Teledyne Microwave Solutions (TMS) offers several Frequency Doublers providing high fundamental suppression, broadband input/output frequencies, and low conversion loss figures for a variety of communications applications.
-
Product
Active Differential Probe, 100 kHz to 7 GHz
U1818A
-
The Keysight U1818A 100 kHz to 7 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818A allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
Product
Digital frequency counters
-
The instrument is equipped, in addition to the 20 Hz-160 MHz input, a second input for measurement up to 2.4 GHz with an impedance of 50 Ohms.
-
Product
IP Converters
-
SMPTE-2022 compliant standalone solutions for conversion between IP and "traditional" DTV signals such as ASI and QAM. These IP converters are hardware-based, providing low latency and zero-jitter transmission of IP signals.
-
Product
Frequency Meter
Reed Type
-
*Vibrating Reed type frequency meters are available in size 72 x 72 & 96 x 96mm suitable 110V, 230V & 440V AC Operation.*Scale 45-50-55 Hz.*Model : SF-72 ( R ), SF-96 ( R ).
-
Product
Frequency Response Function
FRF
-
FFT Spectral Analysis. Frequency Response Function (FRF) is a commonly used measurement type of the Dynamic Signal Analyzer. FRF is defined as the ratio of response i.e. acceleration, velocity, or displacement with respect to the excitation force which is the reference.
-
Product
UP Converter
-
The products have a big Dynamic Range, are highly linear and have low Noise Figures to keep the best possible quality of the signals to be converted. For this reason an internal filter for secondary wave suppression is implemented.
-
Product
Frequency Offset Measurements
S93080B
-
The S93080B frequency offset capability enables the network analyzers to set the source frequency independently from where the receivers are tuned.
-
Product
Plane Mirror Converter
10722A
-
The Keysight 10722A plane mirror converter modifies the use of the 10702A linear interferometer. With an additional 10703A reflector, the 10722A converts the 10702A into a 10706A plane mirror interferometer. With an additional 10723A high-stability adapter, the 10722A converts the 10702A into an 10706B high-stability plane mirror interferometer.
-
Product
DC-DC Boost Converters
-
The ams step-up (boost) converter portfolio offers very high efficiencies of up to 96%, and the devices draw a very low quiescent current. High switching speeds enable the use of very small external inductors. These DC-DC boost converters can boost the input from a single battery cell to an output of up to 42V.
-
Product
DC-DC Converters
-
Samlex America, Inc Power Supplies
Fully Isolated Regulated DC-DC converters provide stable 12V -12V or 24V-24V regulated output power for situations with an unstable input source.
-
Product
Frequency Response Analyzers
7400 Series
-
The Venable Model 7400 Series is the top of the line in Venable performance, supplying 4 channels for increased testing, measurement and analysis functionality. Originally designed for measuring 3-phase impedance and source and load simultaneously, the Model 7400 is a robust solution for organizations requiring high availability for high volume and/or simultaneous testing.
-
Product
DC-DC Converters
-
The standard range of DC-DC Converters contains units with power outputs from 40W to 5kW. Small footprints, high conversion efficiencies and floating outputs are common throughout the converter range. For users that require the highest reliability a number of our converter families demonstrate MTBF figures of 750,000 hours. Our most rugged converter designs are capable of operating in ambient temperatures as low as -40°C and as high +80°C.
-
Product
Optical Path Converter
LS512A/LS512B
-
There are many LED manufactories using two integrating spheres and one spectrophotometer to do test. The previous testing way is: when you use big sphere to test, the customer need to connect the detector cable and optical fiber from the Spectrophotometer to the big sphere, after the calibrating and then you can do the test. When you use the small sphere, you need to take away the detector cable and optical fiber from the big sphere to the small sphere, then need to calibrate again. It is too troublesome to take out the detector cable and optical fiber between the big sphere and small sphere, and you need to calibrate again for every change. The frequent change will also shorten the life of the detector cable and optical fiber.
-
Product
Transition Time Converters
-
These converters have been designed to convert the transition times of instruments with fixed, fast transition times, to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns); hence reducing the signal bandwidth. All transition-times are between 10% and 90% of amplitude.The design of these converters ensures very low signal reflection far beyond the 3 dB point. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with two SMA connectors, one male, one female.
-
Product
Serial Converter
USB-COMi
-
The USB-COMi is a USB to RS485 serial converter. It allows easy serial port expansion without requiring IRQ, DMA, or I/O port resources. The converter allows the user to easily and economically connect RS485 devices to a host using USB. The RS485 communications standard is used by DGH sensor based data acquisition modules and many industrial control devices.
-
Product
Universal Frequency Counters
GT210PXI-2
-
GuideTech’s GT210PXI-2 3U form factor, meets industrial standard chassis with an expandable platform, achieving optimal test system with optimal cost. The ability to precisely resolve frequency and time yields both increased accuracy as well as reduced measurement time.
