Audio Test Systems
See Also: Audio Test, Audio Testers, Speaker, Acoustic
-
-
Product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
-
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
Product
GSP-2B Test System Interface Probe
GSP-2B
ICT/FCT Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 125Full Travel (mm): 3.18Recommended Travel (mil): 125Recommended Travel (mm): 3.18Overall Length (mil): 845Overall Length (mm): 21.46
-
Product
Leak Test System
NorCom 2020
-
The NorCom 2020 batch inspects up to 500 devices per cycle for both gross and ultra-fine leaks. The system incorporates a patented full field interferometer that produces reliable, repeatable leak test results. The system eliminates the need for helium mass spectroscopy or krypton testing for fine, and bubble leak testing for gross leaks.
-
Product
Audio Line Drivers and Receivers
-
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
Product
MB-OFDM Protocol Test System
WiMedia Explorer 300
-
The WiMedia Explorer 300 is the world's first over-the-air MB-OFDM protocol test system for WiMedia Alliance's Ultrawideband common radio platform, Wireless USB protocol and Bluetooth.
-
Product
AC Voltage Test Systems
-
HIGHVOLT Prüftechnik Dresden GmbH
AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
Product
Digital Interconnect Test System, Reference Solution
-
When you need to measure advanced S-parameters with a fast, low-cost and easy-to-use test solution, the Digital Interconnect Test System gives you a significant edge. It provides a full 32-port vector network analyzer (VNA) configured within a single PXI chassis – ideal for high-speed cable testing. And lets you test any linear passive interconnect faster and easier, including backplanes, connectors and PCBs. Sharpen your edge with Keysight’s Digital Interconnect Test System that enables signal integrity characterization of multiport interconnect products.
-
Product
Annual testing of Automatic Identification System
AIS
-
The purpose of an annual testing is to determine that AIS is operational as defined in appropriate performance standards - the International Maritime Organization (IMO) Performance Standard (MSC 74(69)) and IEC standard, IEC 61993-2: Maritime Navigation and Radio Communications Equipment and Standards Automatic Identification Systems (AIS).
-
Product
200 kHz dual domain audio analyzer
SR1
-
Stanford Research Systems, Inc.
SR1 Dual-Domain Audio Analyzer is a stand-alone instrument that delivers cutting edge performance in a wide variety of audio measurements. With a versatile high-performance generator, an array of analyzers that operate symmetrically in both the analog and digital domains, and digital audio carrier measurements at sampling rates up to 192 kHz, SR1 is the right choice for the most demanding analog and digital audio applications.
-
Product
Audio Processors
-
ST’s analog and digital audio processors are suitable for a wide range of applications and offer best-in-class performances in terms of audio quality and features.
-
Product
Optics Test Systems
F Number Meter
-
Optik Elektronik Gerätetechnik GmbH
The f-number of a camera lens is defined as the quotient of the focal length f' and the diameter of the entrance pupil. The f-number measuring device is a simple structure for the automatic, software-controlled measurement of the f-number of optical systems.
-
Product
Partial Discharge Test System
TPP
-
The Partial Discharge Test System type TPP is used for non-destructive insulation and quality testing of electrical components (for example according VDE 0110-1, EN 50178, IEC 60270 and IEC 60060).
-
Product
Audio Frequency Oscillator
PD-5
-
2.5- 100 volt output6 position output voltage selectorCompatible with all "Mark" receivers (Mark II, III, IV, V)Pulse "Identifying" signalBattery charging circuit built-inLED impedance meter
-
Product
Audio Generator
AG-51
-
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and left and right in phase opposition (L-R). Fully balanced or unbalanced outputs at impedance levels 150 ohms or 600 ohms are front panel selectable. Three precision attenuators (10, 1.0 and 0.1 dB) provide a dynamic range of 99.9 dB in 0.1 dB steps. Attenuator dials display the output level directly in dBm in the 150 ohm source impedance configuration. Automatic output leveling circuitry with a built-in self-test feature provides a constant output level thereby eliminating the need for output metering. In the TEST mode the generator output level is reduced to zero, a useful feature during noise measurements.
-
Product
LED Car Audio Meters
VM-1 (For 12V systems)
-
*White LED Backlight*Mil spec FR4 circuit board*Regulated power supply*Constant LED current and brightness regardless of battery voltage (won’t dim with your beat)*20 bright surface mount LEDs*Designed for 12 Volt Systems
-
Product
Nanomechanical Test Systems
-
Bruker’s nanomechanical test systems deliver the highest degree of performance, accuracy, reliability, and versatility for quantitative mechanical and tribological characterization at the nanoscale and microscale. Utilizing multiple patented and proprietary technologies, the Hysitron product line of standalone nanomechanical test systems enable quantitative characterization at length scales unreachable by others.
-
Product
Partial Discharge Testing Of Transformer & Localization System
AE-150™
-
The is designed to detect and localize Partial Discharge activity by correlating acoustic and electric sensors' data. The AE-150™ has many acquisition modes, each used for detecting and locating Partial Discharge activity in a transformer. The AE-150™ unit is mounted on the transformer tank using its powerful magnets that also hold four acoustic sensors.
-
Product
Traction and Induction Motor Test Systems
-
Crest makes state-of-the art test systems for testing 3-phase AC motors used in traction and other industrial applications.
-
Product
ARINC-429 Module
M4K429RTx
Test Module
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
Semiconductor & Electronic Systems Test and Diagnostics Services
-
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
-
Product
System
SYS-28
-
This 28" box coater has a separately ventable top chamber, to allow for faster parts changes and increased productivity. It also is equipped with our FTC-620 flip controller. The flip and rotation motors can be seen on the top. This system uses a Varian tri-scroll pump and a bottom mounted 16" APD cryopump.
-
Product
I3070 In-Circuit Test System Software
-
Improve your i3070 in-circuit test system's test performance with advanced software that increases test throughput and coverage. Expand your testing capabilities and optimize your manufacturing process with these powerful tools.
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
Product
Shock Test Systems
-
Accurately measure the fragility of products and evaluate how they respond to specific shock inputs.
-
Product
Integrated I-V Test Systems
-
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
Product
Diagnostic Test System™
-
The original Teseda system for bench-top stimulus, test pattern debug, validation, device failure mode stimulation in-situ with other Failure Analysis lab equipment such as an EMMI, etc.
-
Product
Full-Featured Life Cycle Test System
LCV
-
Configurations for testing to industry standards: IEC, SAE, BCILife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Product
Suspension Component Test Systems
-
Acoustic quality, vehicle dynamics and stability, and driver comfort play an increasingly important role in the development of new chassis and suspension systems – both passive and active. Noises in suspension components can cause customer dissatisfaction and lead to high warranty costs and are difficult to diagnose especially on historically-used, noisy hydraulic test rigs. The MB Suspension Component Test Rig (SCTR) enables dynamic simulation of real road excitations and synthesized waveforms, performing industry-standard Force-Velocity and Force-Displacement tests and low speed friction tests, and assessing other NVH and structure-borne noises for comprehensive performance characterization and sound and vibration analyses on a wide variety of chassis components.
-
Product
TOV Test System
-
Shanghai Guantu Technology Co., Ltd.
1. Safety protection: traffic light indication status, emergency stop and interlocking of the test product door2. Equipped with a computer, set the TOV power supply parameters through the software interface, and automatically test3. Equipped with alarm function, equipped with emergency brake switch, equipped with safety cover and door switch4. The computer interface displays real-time voltage and current data5. Automatically draw voltage and current waveforms, and can save the waveforms as BMP format pictures, which is convenient for editing experiment reports.6. Automatically record test time, test current, test voltage, etc., and save the recorded data to files7. Installation method: cabinet installation.
