Melt Flow
See Also: Flow
-
product
Flow Meter
V-Cone
The V-Cone Flow Meter is an advanced differential pressure instrument, which is ideal for use with liquid, steam or gas media in rugged conditions where accuracy, low maintenance and cost are important. With its DP built-in flow conditioning design, the V-Cone is especially useful in tight-fit and retrofit installations in which the long runs of straight pipe required by Orifice Plates, Venturi Tubes, and other technologies are either impractical or unavailable.
-
product
Turbine Flow Sensor
2100
Engineered specifically for small diameter applications, the Signet 2100 Turbine Flow Sensor provides accurate readings in two flow ranges; 0.3 to 3.8 lpm and 3 to 38 lpm (0.1 to 1 gpm and 0.8 to 10 gpm).
-
product
Flow Cell Kit
QCMT
The quartz crystal microbalance (QCM) technique under electrochemical frequency is very useful to determine many compounds such as metal proteins, metal ions and thiol-conjugated oligonucleotides.
-
product
High Flow Mass Flow Controllers
High flow thermal mass flow controllers and meters offer both elastomer and metal seals for flow rates up to 300 slm. Versions are available for standard and harsh environments where protection from water and dust is required.
-
product
Vapor Mass Flow Controllers
Heated pressure-based mass flow controllers are designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas.
-
product
Flow Wet-Tap Valve
3519
The Signet 3519 Flow Wet-Tap Valve serves as a unique interface between the installation fitting and the wet-tap style Signet 515 or 2536 Rotor-X Flow Sensor. It provides a fast method of removing the sensor from the pipe under specified operating pressures. The PVC and stainless steel design of Wet-Tap makes it resistant to corrosion and chemical attack by acids, alkalis, salt, and a number of other harsh chemicals.
-
product
TMR Flow Sensors
MultiDimension Technology Co.,Ltd.
A fast frequency response, low power consumption, moisture and water proof rotational speed sensor, incorporating high sensitivity tunneling magnetoresistive (TMR) sensor, signal processing circuit and stainless-steel housing. It is an ideal solution for industrial turbine meter and lobed impeller flow meter applications which requires low power consumption, fast frequency response and harsh operating environment.
-
product
Flow, Level & Valves
We have an extensive range of flow controllers and flow indicators for both liquid and gas applications. We specialize in flow measurement and control of media in flow lines less than 2". Our level control instrumentation is perfect for use with small to medium process and industrial tanks and storage vessels. Choose from level sensors, float switches, optical switches, and ultrasonic transmitters/controllers for single-point control, dual-point control, continuous-level control, and leak detection. Our valve selection offers solutions to meter and control fluids in laboratory, process, and industrial applications. Types of valves available include options from simple and inexpensive plastic ball valves to actuated solenoid and manifold valves. Other types of valves include check, diaphragm, elliptical, metering, needle, pinch, proportioning, and stopcocks. To fit your fluid path, connection types include barbed, compression, luer, sanitary clamp, NPT, and true-union.
-
product
Turbine Flow Meters
CT300, CT400
Flows up to 400 lpm (100 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2-3 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-estersBi-directional
-
product
Probes & Flow Cells
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
product
Mass Flow Meters
Alicat Scientific, Incorporated
Use mass flow meters to measure gas flow from 0.5 SCCM to 10,000 SLPM, with accuracies as good as ±0.5% of reading or ±0.05% of full scale and a measurement range of 0.01-100% (10,000:1 turndown).
-
product
ISO Viscosity Flow Cups
2353
The Elcometer 2353 ISO Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
product
M2730 DIGITAL PORTABLE FLOW CALIBRATOR
M2730 is the new digital portable calibrator of ForTest® M series. Enclosed in a container of anodized aluminium with shatterproof plexiglass front, we find a completely new circuit board and a mass flow meter sensor, for direct measurement of leaks. Coupled to the micrometer nozzle supplied, they are designed to simulate the desired leakage, facilitating the procedure for programming and verification of leak test instruments.
-
product
Certifier Flow Analyzers
TSI Certifier™ Gas Flow Analyzers are multi-functional pneumatic test systems capable of measuring flow, pressure, temperature, and oxygen concentration. They are ideal for testing ventilators, anesthesia workstations, and any other respiratory medical device that produces flows or pressures.
-
product
Ultrasonic Flow Meters
Dalian Taijia Technology Co.,Ltd
RS485 .4-20mA and OCT output● 4-20mA and PT100 platinum resistance input● 2×20 English letters LCD display● 4 key tactile-feedback membrane keypad● IP57● Operate with clamp on, insertion and flow-cell transducer● Pipe diameters from 15mm to 6000mm
-
product
Flow Logger Sensor
NUL-224
This sensor allows for a stream of water to flow through its inlet and outlet pipes, thus revolving a rotation wheel within it. The wheel is not connected mechanically to anything else, but rather floats on a bearing for minimum friction and the enhancement of its minute accuracy. The measuring is done by monitoring changes in the sensor's surrounding magnetic field.
-
product
High-power Melt Blown Cloth Electrostatic Electret Device
HTRP-140B / 516
Wuhan Huatian Electric Power Automation Co., Ltd.
It is widely used in masks, melt-spraying non-woven fabrics, printing, film sticking, spray painting, flocking, sorting and bioengineering.
-
product
Rotational Flow Demonstration Kit
The rotational flow demonstration kit detects the rotational position using the MCU’s on board data transfer controller (DTC) function, a form of state machine, while the MCU’s core is in stop-mode state. This ensures that the average power consumption is kept as low as possible, with IAV (average current) at 4.5 microampere (μA) and a 32 sample burst per second. The flow demonstration kit senses the flow direction and volumetric flow rate of water and gas, and can also detect reverse flow. The demonstration kit is applied using an active inductive method. Two coils are used to sense the rotational position of a part-metalized disk, and a third coil is used to generate a reference signal.
-
product
Clamp-On Ultrasonic Flow Monitor
KATflow 10
The KATflow 10 is a simple ultrasonic clamp-on flow monitor, which provides an extremely cost-effective alternative to in-line flowmeters on effluent, wastewater and sludge applications. The KATflow 10 is used to monitor the flow of liquids containing higher levels of solids or entrained gas bubbles for measurements where a general flow indication is sufficient. The instrument is extremely simple to install and commission and is ideal for applications which demand good repeatability and reliable results.
-
product
flow Coefficient
For the determination of the flow coefficient of fine aggregates up to 4 mm particle size.
-
product
GFS Primary Gravimetric Flow Standard
The GFS dynamic gravimetric mass flow calibration system allows users to maintain the accuracy and traceability of molblocs or other high precision devices using the same primary reference used by Fluke Calibration. GFS is a true mass flow reference suitable for use in premier measurement institutes who require the lowest measurement uncertainty.
-
product
Venturi Flow Measurement Trainer (UITM-22)
Unitech Scales And Measurements Pvt. Ltd
UNITECHS venturi flow measurement trainer comprises of an Venturi meter fitted between the piping. A small FHP pump is used to circulate the water through the piping. Pressure ports brought out from the Venturi meter are connected to a U tube mercury manometer to measure the pressure difference. Collecting tank of capacity 5 liter is provided with graduations to measure water level. Digital timer is fixed to calculate the flow rate. Flow can be controlled using a manual control valve. The complete setup is mounted on a table top model.
-
product
Fast Response Flow Controller for Medium Flow
HFM-301 / HFC-303
The HFM-301 / HFC-303 meters and controllers have flow ranges from 0-25 slm to flows of 0-1000 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a choice of elastomers and high pressure options, the HFM-301 / HFC-303 services a wide variety of applications. Cleaning for oxygen service is available.
-
product
Liquid Flow Controllers
Alicat Scientific, Incorporated
use Coriolis or laminar flow technology to accurately control liquid flows across a wide range of applications. Coriolis flow controllers can accurately control liquid flow rates up to 100 kg/h, including for aggressive liquids and unknown compositions. For water and other non-corrosive liquids, our laminar liquid flow controllers provide real-time control of process flow and pressure.
-
product
Fast Response Flow Controller for Medium Flow
HFM-305 / HFC-307
The HFM-305/HFC-307 is Teledyne Hastings' fast response series of mass flow meters and controllers. Featuring reliability and stability, the 300 Series is chosen for its fast response under a wide range of conditions. .The HFM-305 / HFC-307 meters and controllers have flow ranges from 0-1000 slm to flows of 0-2500 slm; provide analog outputs, are constructed of stainless steel and can be configured to have either normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a choice of elastomers and high pressure options, the HFM-305 / HFC-307 services a wide variety of applications. Cleaning for oxygen service is available.
-
product
Spectroelectrochemical Flow Cell
SEC-2F
Using the spectroelectrochemical flow cell, it is possible to have a different optical path length changing the gasket. We offer, as an optional item, a silicon and Teflon gasket with a 100, 250 and 500 m of the thickness. SEC-2F Spectroelectrochemical flow cell was designed to fit perfectly in the SEC2000 Spectrometer, and it eliminated the use of the optical fiber to connect the Spectrometer to the SEC-2F. Even for another brand of the spectrometer, you can connect the SEC-2F using the collimating lens and optical fiber.
-
product
Turbine Flow Meters
CT15
Flows up to 15 lpm (4 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-esters
-
product
6 Channel Function Generator / Flow Simulator
DP-cPCI-2601
DP-cPCI-2601 is a 6 Channel 2MS/s Waveform Generator with high frequency performance, versatility and compact size in an economical cPCI bus format. Signal output in the range of 10 mHz to 5 KHz with 14 bit vertical resolution makes this single slot, 6U-sized cPCI card a powerful solution to meet most demanding test stimulus.DP-cPCI-2601 uses Direct Digital Synthesis (DDS) technique to generate stable and accurate output waveforms down to 0.01 Hz resolution. DP-cPCI-2601 offers Sine, Square, Ramp, Triangle, Pulse as built-in wave shapes and user defined arbitrary waveform.DP-cPCI-2601 can frequency sweep any of its function outputs. User can sweep upwards using linear sweeps.
-
product
Flow Cytometer
Nowadays, quality control is a key part of any industrial process, in line with dynamically changing standards, and creation of new standards and protocols in accordance to each industry. Flow cytometry is a widely used bioanalysis technique in a larger number of applications. Extensively used in fields like microbiology, the technology has also proven benefits in the food and agrifood industry. A potential application is the absolute somatic cells count in the milk. Flow cytometry can also be applied for environmental and sanitary microbiology for applications such as detection of bacterial cells in milk or water for quality control and assurance testing.
-
product
Turbine Flow Meters
CT800
Flows up to 800 lpm (210 US gpm)Pressure up to 480 bar (7000 psi)Choice of 4-20mA and 0-5V outputs2-3 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-estersBi-directional
