Ground Bond
Checks a ground circuit's ability to handle fault current in the event of insulation failure.
-
Product
Bonding Tester
PTR1102
-
In wire bonding in semiconductor manufacturing, electrodes are joined using gold wires of several tens of microns. In order to measure the pull (tensile) strength and ball shear (shear) strength of this gold wire, this machine has load detection accuracy and fine positioning accuracy. In addition, for the measurement of high load areas such as die shear strength and solder joint strength, this machine supports measurement in high load areas while maintaining accuracy in low load areas by replacing the sensor part.
-
-
Product
Ground Fault Locator
K-3837
-
Kongter Test & Measurement Co., Limited
Kongter’s K-3837 Ground Fault Locator is developed to fast detect, trace and pinpoint virtual grounding faults on LIVE DC systems with earth fault. It will save you from long time unnecessary troubleshooting and helps to increase the stability of your electrical equipments. It is widely used in various DC systems including power utilities, locomotive, telecom and etc.
-
Product
Ground Fault Locator
GFL-1000
-
The GFL-1000 ground fault locator is used to pinpoint faulty grounding where electrical cables have breakage and lost to the ground. The GFL-1000 is recommended by NERC PRC-005-2 to inspect for unintentional grounds for VLA, VRLA and NiCad batteries every four calendar months. Included software allows for data management analysis.
-
-
Product
Ground Fault Location
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of ground fault locator from basic to advanced model to fast detect, trace and pinpoint virtual grounding faults in DC systems when systems are LIVE (working online). Without injecting any signal to the DC system, they are safe to your existing system. With Kongter’s unique technique for signal tracing, these ground fault locators are much faster and more effective to find the earth fault in the field than its peers.
-
Product
Handheld Grounding Tester
HGT1
-
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
Product
DC Ground Fault Finder
FST-JD200
-
Foresight Electronics Co., Ltd.
FST-JD200 not only can provide a solution on accurately testing the faults of the indirect-grounding of the direct current system, non-metal grounding, loop grounding, simultaneous grounding of the anode and cathode, balanced grounding of the anode and cathode and multi-point grounding 1.
-
Product
PE/ Ground, Insulation Resistance Tester
Handheld
-
The safety testers of the Handheld class are used to measure PE/ Ground resistances, insulation resistances and to perform a simple functional test. The small and sturdy universal testers are intended for standard-compliant safety tests in workshops and production as well as for mobile operation during repair, installation, service and more.
-
Product
Earth Ground Testers
-
Fluke''s family of earth ground testers have been built to address the entire spectrum of ground testing methods from the basic to the most advanced. Our testers have been designed to be accurate, safe and easy to use. We provide quick and precise resistance measurements through several test methods: 3- and 4-pole Fall-of-Potential testing, selective testing, stakeless testing and 2-pole testing. Detailed application information can be found at the Earth Ground Solution Center.
-
Product
Ground Resistance Tester
-
Weshine Electric Manufacturing Co., Ltd
1.Soil resistivity tester supports 2, 3 and 4wire grounding resistance measurement. 2. 4digit large LCD display with white screen backlight, suitable for use in dimly lit places. 3. IP65 protection grade, good waterproof, compact and portable, supports multiple functional tests.
-
Product
System Grounding & Earthing Analysis
-
ETAP's system grounding & earthing foundation automatically detects the system earthing configuration based on source and transformer grounding or earthing type selection. The resulting earthing types are displayed both on the one line diagram and for the various connected cables.
-
Product
Ground EMI Filters
-
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
-
-
-
Product
Ground Resistance Clamp Meter
61-920
-
*Auto ranging*Auto power off*Hard case included*2-year warranty
-
Product
Bond Tester for Wafers 2 - 12 inch
Sigma W12
-
Bondtester for wafers or at wafer level 2” – 12” (up to 300 mm)Precise testing and Cold Bump Pull (CBP) testingLarge X/Y stages X: 600mm, Y: 370 mmForce range from 1gf – 10 kgfBump pitch down to 20 µm
-
Product
Scott Internal Bond Impact Tester
-
The Scott Internal Bond Impact Tester is used to determine tear resistance (Elmendorf). A sample is torn with the help of the pendulum device starting from a predetermined cut. The work required for a tear of a given length is measured.
-
Product
Aeronautical Ground Earth Station Emulator
GES
-
Square Peg Communications Inc.
Ground Earth Station (GES) emulator provides a simple and flexible means of testing the operation of Aeronautical Earth Stations (AESs) and end-to-end applications for the Inmarsat Classic Aero service, without the expense of airtime charges. It can be used to test basic AES functionality, including Aero I/H+ and Aero H voice calls, and data transfer applications such as ACARS.
-
-
-
Product
AIR SURVEILLANCE AND GROUND BASED AIR DEFENCE
GIRAFFE AMB
-
The system monitors the air volume 360 degrees for air targets and simultaneously locates and warns against incoming rocket, artillery and mortar rounds, and at the same time able to provide coastal surveillance.
-
Product
Heavy-Duty Circuit Tester With Grounding Adapters
30610
-
Heavy-duty circuit tester with multiple options for connecting to a ground source. Long, 12’ cord has a quick coupler to securely connect clamp or power outlet plug. Large, strong clamp connects securely. Power outlet plug can always be used to provide ground in the cabin. For testing circuits up to 12 volts.
-
Product
Long Spring Ground for ZD Differential Probe Qty 2
PACC-ZD003
-
Long spring ground for ZD differential probe Qty 2
-
Product
High Force Large Area Bond Tester
Sigma HF
-
- For high force and large area- Typically for IGBT, power modules and batteries up to 1000 kgf- High axis speed- Deep access up to 80 mm- SEMI S2 safety cabinet with visual feedback- Flexible positioning of multiple work holders
-
Product
Resistance Grounded Systems (HRG/LRG)
-
Neutral Grounding Resistors (NGRs) are used to limit the maximum ground-fault current. Restriction of fault current lowers hazards and reduces damage done to equipment. High Resistance Grounding (HRG) systems are often used on industrial and critical power applications to maintain system uptime during a first ground fault. HRG systems are also used in tripping applications to help control touch potential on portable loads and improve personnel safety.
-
Product
DC Ground Fault Locators
-
We currently offer one highly capable DC ground fault locator for sale to the United States, Canada and Globally. This fault locator is highly reliable and highly capable of locating any ground fault in a variety of settings. This one piece of ground fault locator equipment is all you will ever need to find any fault, in any location, in any system. With advanced computations and fuzzy logic it can very accurately display the insulation level of the tested circuit. We offer the best and only ground fault locator you will ever need. To learn more about his product please click below where you will also be provided key features and the ground fault locator specifications.
-
Product
7U VPX 1 Slot Power & Ground 25G Pass Through
101VPX701P-9X13
-
Power for 3.3V, 5V and 12V are included, rear connectors areall fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
3U VPX 1 Slot Power & Ground 25G Pass Through
101VPX301P-9X13
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
