-
Product
UL94 Combustion Chamber, IE60695vFlammability Tester
CX-S16
-
Shenzhen Chuangxin Instruments Co., Ltd.
Horizontal Vertical Flame Tester is a comprehensive test instrument whick strickly designed according to Standard IEC60695, GB5169, UL94 and can meet the relative standard's requirements. It's mainly used to test the flammability of plastic and other nonmetalloid parts specimen to evaluate fire hazardous degree of accidental burning caused by the material.
-
Product
Compensating Reactor
-
The compensating reactors are accessories for the CTS-12KSA/ACTS-12K Capacitance & Tan Delta Test Set. The use of one or more compensating reactors increases the capacitance that the internal power supply can excite to conduct measurements. As the measuring range of the CTS-12KSA / ACTS 12K exceeds the kVA rating of the internal power supply, one way of using the test set over its entire measuring range is to form a resonant circuit with the test sample. The use of one or more compensating reactors forms partial resonating circuit with the test specimen, thereby reducing the power supply requirement.
-
Product
Needle Microprobe
MT-23/3HT
-
Fast-response 23 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Climate Control Test Chamber
-
ACMAS's Climate Test Chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. ACMAS Thermal Cyclic Chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperature ramp control. This chamber is also known as Climatic Test Chamber and Climate Controlled Test Chamber.
-
Product
Universal Testing Systems (Up To 300 KN)
6800 Series
-
Instron’s 6800 Series universal testing systems deliver high-performance mechanical testing up to 300 kN. Designed for precision and durability, these systems offer exceptional measurement accuracy (±0.5% down to 1/1000th of load cell capacity) and fast data acquisition rates up to 5 kHz. Ideal for tensile, compression, flexure, torsion, peel, lap shear, and many other test types, the 6800 Series provides the flexibility and control needed to handle everything from delicate specimens to high-strength materials, making it a trusted solution for demanding testing environments.
-
Product
Vertical Flammability Chamber
TF312
-
TESTEX Testing Equipment Systems Ltd.
Comprises a draft free stainless steel flammability chamber with observation window for easy test viewing. Specimen holders, burner and associated hardware are dependent on the test standard and must be specified.
-
Product
Ball Pressure Test
-
Premier Electrosystems' Ball Pressure Test is used to determine dimensional stability under stress at elevated temperatures. It analyses the relationship between the degree of deformation and the temperature when the test specimen is subjected to a constant load.
-
Product
Environmental Test Chambers
-
Dongguan Kejian Instrument Co., Ltd.
UV accelerated weathering test chamber simulates damaging effects of long term outdoor exposure of sunlight, heat, moisture on materials and coatings. It exposes specimen to varying conditions of weathering- ultraviolet radiation, moisture and heat to test the performance and improve the quality.
-
Product
IEC60558 Insulation Material Layer Abrasion Resistant Test Device
CX-J16
-
Shenzhen Chuangxin Instruments Co., Ltd.
This test is conforms to IEC60558-1 Fig6 and IEC60065 Fig14--16.The test shall be performed by fixing the specimens of thin sheets on a mandrel made of nickel plated steel or brass with smooth surface finish.
-
Product
Specimen Radiography System
XPERT 40
-
Whether in the biopsy suite or the pathology lab, nothing beats the XPERT 40 Specimen Radiography System in terms of versatility and speed. A 50kV, 1.0 mA X-ray penetrates the densest cores and surgical specimens, identifying the finest details in seconds.
-
Product
Micro Vickers Hardness Tester
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ MicVision main use in testing materials allows for the measurement of the hardness of small or thin specimens and small areas of larger specimens, MicVision testing is commonly used to determine characteristics of thin sheets, foils, fine wire, epoxies, paints, etc. and is often employed in R&D applications .◆ MicrVision hardness is especially useful in determining hardness variations, caused by hardening, quenching, plating, fabrication, welding or annealing, bonding, etc. Micro hardness testing can be accurately employed using loads as slight as 10 gram, somewhat less and considerably more in certain situation.
-
Product
Bi-Axial or Axial Averaging Extensometers
Model 3560
-
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Downproof Tester
TF134
-
TESTEX Testing Equipment Systems Ltd.
Take an agreed size specimen from the fabric to be tested to sew a pocket at specified size , fill with a certain Weight of down, feathers or a mixture of both, then sew the fabric up to be a testing bag. Clamp the both sides of the bag in the holder. After test to determine the downproof ability of the fabric by calculating the number of down and feathers through the fabric
-
Product
Mini Cloud & Pour Point Analyzer
OptiMPP
-
The automated OptiMPP provides highly accurate cloud and pour point results using only 0.5 ml sample. Simply place the sample in a disposable vial into the 20 specimen sample changer and press the OK key. No special programming or expected point is required. Results are available in 20 minutes for a -30ºC pour point.
-
Product
Light Sheet Microscopes
-
Life science research can place high demands on your imaging capabilities: Sometimes you need to image whole living model organisms, tissues and cells as they develop. Or you may want to observe subcellular dynamics in living samples over hours and even days. Light sheet fluorescence microscopy (LSFM) with its unique illumination principle is ideal for fast and gentle imaging of such specimens.
-
Product
Brush or Sponge Pilling Tester
TF222
-
TESTEX Testing Equipment Systems Ltd.
Brush or Sponge Pilling Tester, to determine the pilling propensity and simulate normal wear of knitted and woven fabrics used in apparel and automotive interiors by brush and/or sponging specimens together in a circular motion to form pills. Specimens are evaluated under standard lighting conditions using a pilliscope, light cabinet or similar, against users’ standard fabrics or piling photographs.
-
Product
Needle Microprobe
MT-D
-
Fast-response 29 gauge needle surface probe for locating inflammation, arteries, etc. Also for dental use. 1/4'' right angle needle length, 3/4'' needle distance from lead. 5.5'' long handle for ease of use. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Sensor within .3mm of tip. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Temperature shock test chambers test
TSS series
-
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
-
Product
1 KN Henry Scott Grips
-
Henry Scott grips are useful for clamping plate and tape specimens of soft, flexible materials for tensile testing. Specimens are held by rollers on the upper and lower grips, which feature a self-clamping action. To minimize specimen slippage, the grip body opposite the roller, where the specimen contacts, is curved and features a parallel-grooved surface. During tensile testing, the self-clamping action applies increasing clamping force to the specimen as the overall force increases to help hold the specimen in place.
-
Product
Fully Automatic Tensile Testing System
-
This is a fully automatic tensile testing system for metals. The system is fully automated from supply of specimens, measurement of specimens, tensile testing, recovery of specimens, and data processing, and is capable of continuous nighttime testing.
-
Product
Test Adapter / Extender
-
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
Product
2- and 4-Mirror Floating Zone Crystal Furnaces
IR Image Furnace
-
The high-performance, compact IR Image Furnace from Quantum Design offers unsurpassed performance in a convenient, stand-alone design. Rivaling much larger and more costly IR furnaces, it uses the Floating Zone (FZ) method to promote single crystal growth from a polycrystalline rod. This method has been shown to be extremely effective for a wide class of materials. Now, more easily than ever before, you have the ability to synthesize superior quality single crystal specimens in your own laboratory. This furnace is available in both 2- and 4-mirror versions.
-
Product
Data Logger for Ultra Low Temperature
DSR-ULT
-
Special probe using military industrial technology supports measuring temperature ultra low to -100 Original fittings for sensor connection, ensures 100,000 plugs Support single DSR connecting to PC via USB interface, and multiple DSR grouped in RS485 or LAN networking for central management Suitable for medical refrigerator, biological specimens preservation, scientific research and other applications
-
Product
Secondary Ion Mass Spectrometry (SIMS Analysis)
-
Rocky Mountain Laboratories, Inc.
Secondary ion mass spectroscopy is operated either in the dynamic mode (DSIMS) or the static mode (SSIMS). DSIMS is useful for profiling impurity and trace elements through films and interfaces. SSIMS is useful for characterizing polymeric materials and only measures the outermost molecular layer of a specimen.
-
Product
Condensation Tester
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Condensation tester simulates the damaging effects of outdoor moisture attack by condensing warm water directly onto test specimens. In a few days or weeks, the tester can reproduce the damage due to moisture that occurs over months or years outdoors.
-
Product
Concrete Bulk Resistivity
RCON
-
Giatec RCON™ is a non-destructive device for measuring the electrical resistivity of concrete specimens in the laboratory without any additional sample preparation requirements. This measurement can easily be made on the same concrete samples that are currently used for the compressive strength testing of concrete.
-
Product
Needle Microprobe
MT-4
-
Fast-response 29 gauge needle probe with blunt tip, (needle length is 1cm) for instant readings. Good for instant skin temperature and surface temperatures, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
High-end Transmission Electron Microscope
CryoARM
-
JEOL announces the latest member in its family of high-end transmission electron microscopes, the CryoARM. This highly automated TEM is designed for unattended operation and high throughput imaging of cryo-EM specimens. The CryoARM was initially introduced to a select audience at the 2016 Gordon Research Conference in Hong Kong, M&M 2016 in Columbus, OH and EMC 2016 in Lyon, France. The CryoARM is a dedicated cryo-TEM, based on the highly successful JEOL ARM (Atomic Resolution Microscope) series, an ultrahigh performance, highly stable platform considered to be the "best-in-class" TEMs. The development of the CryoARM was accomplished in collaboration with leading Life Science researchers.
-
Product
S-parameter Measurement System
DPS21
-
Unlike a coaxial tube type or a wave guide tube type, this method does not make errors caused by air-gap as specimens are not put into a fixture. Practical data can be obtained even at the rough, uneven surfaces where the specimen is placed on.It enables compactness and measuring specimens by plane wave because of direct installment of lens with an antenna.It enables measurement by monitoring S21 and S11 parameter with connections of a test fixture to a vector network analyzer and PC.
-
Product
Press-type Vibration Tester
9363-PC-ESS
-
King Design Industrial Co., Ltd.
This machine complies with the IEC, JIS and other 5-100Hz low-frequency specifications; applied to test the post-assembly products at end of the production line. Use resonance amplification, the product’s flaws can be screened out in advance. The operation is convenient, fast and effective.Apply Japan-imported motor; durable and safe in operation.Bellow-type damper: use special damping material that can effectively absorb vibration; allowing the test to be performed without affecting floor structure.Motor drive system is embedded in the seat; good in vibration block-out; rigidity is strong. Follow specimen to design fixture.
