-
Product
Low Temperature Chamber
-
The Ultra Low Temperature Test Chamber from Weiber are specially designed equipments that provide specific low temperature environments for testing a wide variety of products and their performance under non-ambient testing conditions. They are engineered and configured to meet the exacting low temperature requirements of various research applications and often find their use for evaluation of material properties at extreme temperatures. These versatile test chambers offer the capabilities of measuring temperature extremes, allowing both freeze tolerance studies as well as the effect of heat stress on the sample specimen within the same equipment. They combine advanced technological features with an energy efficient design for highly accurate test conditions and repeatability of results. These test chambers provide a cost-effective solution to expensive laboratory tests and are available at economical prices for increased affordability. They are designed for safe and reliable operation and find widespread usage in chemical and pharmaceutical industries, biotechnology and medicine industry, petroleum industry, food industries and other industrial and manufacturing units.
-
Product
Computer Control Torsion Testing Machine
NDW Series
-
Jinan Testing Equipment IE Corporation
NDW Series computerized torsion testing machine provides loading and weighing capabilities in both rotation directions which enables it to determine conveniently not only the ultimate torque of a specimen, but also how the specimen behaves under conditions of continuous or intermittent torque loading in both directions. The computerized torsion testing machine is mainly used for the torsion test of metal and non-metal materials, as well as the torsion test for parts and components. The computerized torsion torsion testing machine is an essential instrument to measure torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
-
Product
Multi-Station Test Frame
6800
-
The 6800 Series Multi-Station System offers enhanced throughput with its ability to perform simultaneous, independent tests on up to five (5) separate specimens using a single load frame. Based on our standard 68TM-30 testing frame (30 kN capacity)*, this system is especially suitable when test times are lengthened due to high elongation or slow test speeds.
-
Product
Thermal Microscope Stage
TS-4MP
-
With our TS-4MP Thermal Stage, a specimen on a microscope slide or culture dish can be maintained at any temperature between -20°C and +60°C. Setup is easy, takes little time, and the controller will regulate the stage temperature to within +/-0.1°C
-
Product
Automatic Upset Testing Machine
YQA Series
-
Jinan Testing Equipment IE Corporation
This kind of machine is designed according to the International standards EN 10263-1:2001 “Metallic materials upset test methods”, especially for the quality inspection of high-speed rods and wires. Through simulating the quick press conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. This kind of machine is widely used in the steel industry, standard samples manufacturing industry, and tools manufacturing industry, for the inspection of the metallic materials upset tests. Under the room temperature or the hot conditions, exert test force on the direction of specimen axial line, quickly compress the specimen, and then inspect the metal ability of bearing upset deformation in the specified upset ratio. It also can show the metal surface disfigurements.
-
Product
Grips For Plastic Molding Materials
-
These plastic molding material grips are used when tensile testing plastics with dimensions specified in JIS K6911, plastic molding materials, and JIS K7113 No 3 specimens, as well as those shown in the diagram below.
-
Product
Axial Extensometer
Model 3542
-
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
Product
SMH Type Biaxial Tension Tester
-
It is a biaxial tension tester dedicated to this test that conforms to ISO 16842: 2014 "Double-axis tension test method using cruciform specimens of thin sheet steel". National university corporation Tokyo University of Agriculture and Technology industry-university joint research and development product product
-
Product
Salt Spray Chambers
MX-9200
-
LR Environmental Equipment Co. Inc.
A high reliability thermostatic temperature controller maintains the salt solution at a preset controlled temperature in a reservoir within the double wall construction. The salt solution is introduced into the chamber through an atomizing nozzle. The nozzle can be calibrated by us to perform to MIL-STD-19500B, paragraph 40.8 and other specifications. This specification requires that a salt residue be deposited on the specimens, in addition to generating salt fog atmosphere.
-
Product
Heat Seal Tester
HST-01A
-
Jinan Leading Instruments Co., Ltd.
HST-01A Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated films according to the requirement of relative standards. The seal parameters include heat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
Product
Flexible Implantable Microprobe
IT-1E
-
IT-1E Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Similar to our most popular IT-18 microprobe but the sensor bead is exposed, resulting in the same ultra-fast response time of the IT-23 but with the Teflon™ sheath strength of the IT-18. Time constant 0.005 seconds. Tissue Implantable with a 18 gauge needle (supplied). Rather fragile at tip. Coated in Teflon™. Maximum Temperature 150°C. Isolated. Probe tip diameter .011", sheath diameter .025'' . 3 foot lead.
-
Product
5 KN Wedge Grips For Metal Specimens
-
These easily-operated wedge grips are for tensile testing thin metal plates and metal wires. Although these grips don't benefit from the stationary grip face feature of non-shift wedge grips, they still incorporate a wedge design, where the grip faces press against the wedged frame during testing, applying a self-tightening action to hold the specimen firmly in place.
-
Product
Reusable ICP® Strain Gauge
-
This high-resolution dynamic alternative to bond foil strain gauges uses a quartz sensing element in a durable, titanium housing. It has 0.0006 microstrain resolution, 5 volt output, 100k Hz frequency response and 0.5 gram mass for lightweight test articles. The reusable sensor comes with a calibration certificate, attaches to the test specimen in 60 seconds and is removed in 10 seconds.
-
Product
Salt Spraying Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is glad to be the ODM/OEM manufacturer of Salt Spraying Chamber,Salt Spray Test Chamber,salt spraying test chamber,Salt spraying chamber,Salt spraying chamber sales enterprises all over the world! 1：It adopts 5mm or 8mm imported gray and white impact resistant P.V.C board, with high temperature resistance up to 85℃ and corrosion resistance. 2：Support frame: ¢ 10MM fiberglass rod, corrosion resistant. The steel V-frame and the fiber rod angle are placed to ensure the specimen is inclined at 15-30 degrees. 3：Pressure barrel is welded seamlessly with 2.0MMSUS304 stainless steel plate 4：The heating adopts titanium alloy electric heating tube. It has high corrosion resistance and long service life is 3-5 years higher than ordinary stainless steel heating tube. 5：The cover is made of 5MM imported transparent (Germany YLIS) acrylic sheet. It has fine workmanship, beautiful appearance and high transparency.
-
Product
1 N Clip Grips
-
These very low force 1 N (0.22 lbf) clip grips are for tensile testing fibers, tapes, and other similar shaped specimens. They are designed for use with 50 N (11 lbf) and below load cells.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
Electrodynamic Vibration Test Systems
CV-series
-
CV-series is suitable for transportation tests. The lateral support stiffness and maximum displacement of the CV-series are large enough to be accommodate vibration tests of the specimens with high center of gravity.
-
Product
Automatic Compression Testing Machine
CTEN Series
-
Jinan Testing Equipment IE Corporation
This series compression testing machine is mainly designed for compression test of building material items, such as concrete cube, concrete blocks, cement specimen, and bricks etc, also used for compression performance test of rubber pad and top forge test of metal. With new design idea and advanced technology, this series have more advantages in appearance, operation & applications. It is the ideal test equipment for quality control at industry & mineral enterprises, education in high schools, and technology researches at scientific institutes
-
Product
Event Detectors
105/106 Series
-
The 105/106 Series Event Detectors are the most versatile Event Detectors in the product line. These Event Detectors monitor the electrical resistance of up to 128 simple continuity loops, each comprised of single or multiple specimens under test. Each test specimen is continuously monitored while a selectable DC sense current is passed through each channel test-loop; resistance changes exceeding the selected threshold are recorded as an event. Minimum Event Duration, Channel Current, and Threshold Voltage settings can all be independently configured. 105 and 106 Series instruments are electrically identical, with the difference simply that the 105 offers four, 32-channel board slots and the 106 offers only one. Thus the 128-105 is equivalent to four 32-106 Event Detectors.
-
Product
Upset Testing Machine
YQ/YQR Series
-
Jinan Testing Equipment IE Corporation
The series of upset testing machine are designed according to the International Standard 'Metallic Materials Upset Test Methods', especially for the quality inspection of high-speed rods and wires. Through simulating the quick impact conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. Under room temperature or hot conditions, exert test force in the direction of specimen axial line, quickly compress the specimen, and then the machine can inspect the metal ability of bearing upset deformation in the specified upset ratio. The upset testing machine can also show the metal’s surface disfigurements. The upset testing machine is widely used in the steel industry, standard specimen manufacturing industry, and tools manufactures for inspecting the upset tests of metallic materials.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS AUTOMATIC
-
Optik Elektronik Gerätetechnik GmbH
Automatic measuring instrument for contact angle and free surface energy with motorized pump, automatic drop placement and motorized specimen table (200 x 200) mm.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
Test Instrument
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
SUNTEST
XXL+
-
Atlas Material Testing Solutions
The Atlas SUNTEST XXL+ is a large xenon lamp weathering and lightfastness test chamber meeting various ISO, ASTM, and ICH industry standards. Its horizontal 3000 cm2 exposure area is best-in-class for 3-D specimen testing.
-
Product
Vacuum Leak Tester
MFY-CM
-
Saicheng Vacuum Leak Tester (also called Leak Detector, Leak Test Apparatus) is professionally designed for the leakage tests of packages, bottles & pouches for food, drugs, medical instruments, household chemical products, cars, electronic components, stationeries and other industrial products. The instrument also can be used to test seal performance of specimens after falling and compression tests.
-
Product
Testing of Rear Axle Steering
-
*2 high-precision servo axes for linear load simulation*Communication via CAN / Flexray*Function and noise measurements (NVH)*Supply and discharge of the test specimens via WTs on double belt conveyors*Connection to the production control
-
Product
Eddy Current Testing
-
Shanghai Xianda Denshijiki Industry Co.,Ltd
And the eddy current generated on the specimen by the specimen by the action of the magnetic field can not be detected (defect) and the change due to the influence of the material is detected.
-
Product
High-Temperature Extensometers < 600 °C Capacitive
-
Instron® High-Temperature Extensometers are perfect for testing advanced composites, metals, polymers and other materials at elevated temperatures. This series incorporates a capacitive sensor that does not require any cooling. The extensometers come standard with a sensor conditioner unit providing a 0-10 V output with exceptionally low noise. These extensometers can be attached to round and flat specimens to perform tensile, compression, and cyclic tests.
-
Product
Vibration Test
-
Vibration testing determines the dynamic effects on component part of vibration within the frequency ranges and magnitudes that may be encountered during field service. Vibration, for example, causes loosening of parts or relative motion between parts in the specimen, producing objectionable operating characteristics, noise, wear, and physical distortion, and often results in fatigue and failure of mechanical parts.
-
Product
Whole Sole Flexing Tester
SG-P03E
-
Use a cutting tool to pierce the specimen between the cleats at three points along the line of maximum bending stress. By the specified speed and times of 90°bending action to inspect the cuts’ growth with a measuring.
-
Product
Rapid Automated Modular Microscope
RAMM
-
Applied Scientific Instrumentation
*Featuring automated high-speed XY stages, precision piezo & motorized Z focusing, and a wide range of scanning options.*Configurable with infinity-corrected optics, dichroic filter cubes, multi-wavelength excitation and emission filterwheels, shutters, and detectors including cameras and photomultipliers.*Auto-focus, focus stabilization, tracker, and robotic specimen loader available.*Arrangement provides a solid platform for high throughput screening, genetic sequencing, experimental research, and much more.*Designed for flexible cost-effective OEM development using high quality high MTBF components to reduce cost and increase customer satisfaction.
